add USB ids for the mos7840 based ATEN International serial devices.

Contributed by: Phillip Branch
Signed-off-by: NTony Cook <tony-cook@bigpond.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix this build error when CONFIG_PM is not set:
drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bug Fix: high speed detection in LPM mode
Bug Fix: max packet size configuration when switching between HS and FS
Signed-off-by: NDavid Lopo <dlopo@chipidea.mips.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reported by Alessio Treglia on
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/125250

User was getting the following errors in dmesg:

[ 2158.139386] sd 5:0:0:1: ioctl_internal_command return code = 8000002
[ 2158.139390] : Current: sense key: No Sense
[ 2158.139393] Additional sense: No additional sense information

Adds unusual device support.

modified:   drivers/usb/storage/unusual_devs.h
Signed-off-by: NChuck Short <zulcss@ubuntu.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NStefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1229) fixes a few lifetime and locking problems in the
usb-serial driver.  The main symptom is that an invalid kevent is
created when the serial device is unplugged while a connection is
active.

	Ports should be unregistered when device is disconnected,
	not when the parent usb_serial structure is deallocated.

	Each open file should hold a reference to the corresponding
	port structure, and the reference should be released when
	the file is closed.

	serial->disc_mutex should be acquired in serial_open(), to
	resolve the classic race between open and disconnect.

	serial_close() doesn't need to hold both serial->disc_mutex
	and port->mutex at the same time.

	Release the subdriver's module reference only after releasing
	all the other references, in case one of the release routines
	needs to invoke some code in the subdriver module.

	Replace a call to flush_scheduled_work() (which is prone to
	deadlocks) with cancel_work_sync().  Also, add a call to
	cancel_work_sync() in the disconnect routine.

	Reduce the scope of serial->disc_mutex in serial_disconnect().
	The only place it really needs to protect is where the
	"disconnected" flag is set.

This fixes the bug reported in

	http://bugs.freedesktop.org/show_bug.cgi?id=20703Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDan Williams <dcbw@redhat.com>
Tested-by: NMing Lei <tom.leiming@gmail.com>
Reviewed-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make the wusb_chid sysfs file match the ABI documentation.

Print all zeros if the WUSB host is stopped (instead of an empty file)
and end the file with a newline.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix an oops in wusbhc_giveback_urb() if the wusb device had disconnected
while an urb was in progress. Also release the ref count obtained here.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure all WUSB devices are disconnected when stopping a WUSB HCD so
that we don't leak the devices' wusb_dev structures.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check the return value of usb_hcd_link_urb_to_ep() and do not add the
urb to the ASL/PZL if it returns an error.

Omitting the check results in urbs that appear to be submitted
successfully but then cannot be unliked (because
usb_hcd_check_unlink_urb() returns an error).  This can cause khubd (for
example) to block forever in usb_kill_urb().
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Provide a endpoint_reset method to reset sequence number and current
window.  This QHead information can only be changed while the qset is
not in a schedule.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit.  So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).

usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.

If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The v950 appears to be a ruggedized version of the Motorola Razor
phone.  Tethering to the phone to use it in 'phone as modem' mode
requires the use of the specialized moto-modem driver which layers
over the usb-serial driver.  Support for the v950 was added simply
adding the device ID's for the phone.
Signed-off-by: NDr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1228) fixes a Makefile error introduced when the
subdrivers in usb-storage were split out into separate modules.  The
intention is that when CONFIG_USB_LIBUSUAL is set, libusual.o and
usual-tables.o should be combined into a single object file (called
usb-libusual).  The current Makefile will instead create two separate
objects, and the result won't load properly.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NAlan Jenkins <sourcejedi.lkml@googlemail.com>
Reported-and-tested-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

commit 664d5df9 upstream.

Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS

Features still missing:
- character length other than 8 bits
- parity settings
- break control

I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.

Usage example by Tollef Fog Heen :
        TEMPer USB thermometer <http://err.no/src/TEMPer.c>

based on a patch by:

	From: Tollef Fog Heen <tfheen@err.no>

	* Implement support for all baud rates rather than just a hard
	  coded set.
	* Make it possible to control status and control lines
	* Grab a bunch of #defines from FreeBSD to reduce the number of
	  magic numbers in the file
Signed-off-by: NWerner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: NBoris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NTollef Fog Heen <tfheen@err.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reverts commit 664d5df9 as the commit
log information was not complete, and we didn't have a proper
signed-off-by by the author of the original BSD code.

Cc: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Cc: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

During driver resume processing, musb could cause a kernel panic.
Fix by enabling the clock earlier, with the resume_early method.
Signed-off-by: NKim Kyuwon <q1.kim@samsung.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Multi-frame isochronous TX URBs transfers in DMA mode never
complete with CPPI DMA because musb_host_tx() doesn't restart
DMA on the second frame, only emitting a debug message.
With Inventra DMA they complete, but in PIO mode.  To fix:

 - Factor out programming of the DMA transfer from
   musb_ep_program() into musb_tx_dma_program();

 - Reorder the code at the end of musb_host_tx() to
   facilitate the fallback to PIO iff DMA fails;

 - Handle the buffer offset consistently for both
   PIO and DMA modes;

 - Add an argument to musb_ep_program() for the same
   reason (it only worked correctly with non-zero
   offset of the first frame in PIO mode);

 - Set the completed isochronous frame descriptor's
   'actual_length' and 'status' fields correctly in
   DMA mode.

Also, since CPPI reportedly doesn't like sending isochronous
packets in the RNDIS mode, change the criterion for this
mode to be used only for multi-packet transfers.  (There's
no need for that mode in the single-packet case anyway.)

[ dbrownell@users.sourceforge.net: split comment paragraph
into bullet list, shrink patch delta, style tweaks ]
Signed-off-by: NPavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MUSB code clears TXCSR_DMAMODE incorrectly in several
places, either asserting that TXCSR_DMAENAB is clear (when
sometimes it isn't) or clearing both bits together.  Recent
versions of the programmer's guide require DMAENAB to be
cleared first, although some older ones didn't.

Fix this and while at it:

 - In musb_gadget::txstate(), stop clearing the AUTOSET
   and DMAMODE bits for the CPPI case since they never
   get set anyway (the former bit is reserved on DaVinci);
   but do clear the DMAENAB bit on the DMA error path.

 - In musb_host::musb_ep_program(), remove the duplicate
   DMA controller specific code code clearing the TXCSR
   previous state, add the code to clear TXCSR DMA bits
   on the Inventra DMA error path, to replace such code
   (executed late) on the PIO path.

 - In musbhsdma::dma_channel_abort()/dma_controller_irq(),
   add/use the 'offset' variable to avoid MUSB_EP_OFFSET()
   invocations on every RXCSR/TXCSR access.

[dbrownell@users.sourceforge.net: don't introduce CamelCase,
shrink diff]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We really want to use DMA mode 1 for all multi-packet transfers;
that's one IRQ on DMA completion, instead of one per packet.

There is an important issue with such transfers, especially on
the host side:  when such transfers end with a full-size packet,
we must defer musb_dma_completion() calls until the FIFO empties.
Else we report URB completions too soon, and may clobber data in
the FIFO fifo when writing the next packet (losing data).

The Inventra DMA support uses DMA mode 1, but it ignores that
issue.  The CPPI DMA support uses mode 0, but doesn't handle
its TXPKTRDY interrupts quite right either; it can get stale
"packet ready" interrupts, and report transfer completion too
early using slightly different code paths, also losing data.

So I'm solving it in a generic way -- by adding a sort of the
"interrupt filter" into musb_host_tx(), catching these cases
where a DMA completion IRQ doesn't suffice and removing some
needlessly controller-specific logic.  When a TXDMA interrupt
happens and DMA request mode 1 is active, that filter resets
to mode 0 and defers URB completion processing until TXPKTRDY,
unless the FIFO is already empty.  Related filtering logic in
Inventra and CPPI code gets removed.

Since it should be competely safe now to use the DMA request
mode 1 for host side transfers with the CPPI DMA controller,
set it in musb_h_tx_dma_start() ... now renamed (and shared).

[ dbrownell@users.sourceforge.net: don't introduce more
CamElCase; use more concise explanations ]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MUSB host side can't share generic TX FIFO flush logic
with EP0; the EP0 TX status register bits are different
from those for other entpoints.

Resolve this issue by providing a new EP0-specific routine
to flush and reset the FIFO, which pays careful attention to
restrictions listed in the latest programmer's guide.  This
gets rid of an open issue whereby the usbtest control write
test (#14) failed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1227) adds the MAX_SECTORS_64 flag to the unusual_devs
entry for the Simple Tech/Datafab controller.  This fixes Bugzilla
#12882.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Nbinbin <binbinsh@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Someone noted that the enqueue path used an unlocked access
for usb_host_endpoint->hcpriv ... fix that, by being safe
and always accessing it under spinlock protection.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cdc-wdm needs to ignore extremely malformed descriptors.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a set of device IDs from the Windows drivers. These aren't complete
(there's a couple of cases where a QDL device is identified without the
associated modem being identified), but it's better than the current
situation.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch allows D-Link DWM-652 3.5G modem to work.
It is an express card but was only tested with the provided usb adapter as I
don't have machines with express card connector.

/dev/ttyUSB{0,1,2} get created, and using comgt on ttyUSB1 works fine :

[root@plop tmp]# comgt -d /dev/ttyUSB1 -e

Enter PIN number: XXXX
Waiting for Registration..(120 sec max).
Registered on Home network: "Orange France",2
Signal Quality: 15,99

From: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The g_ether USB gadget driver currently decides whether or not there's a
link to report back for eth_get_link based on if the USB link speed is
set. The USB gadget speed is however often set even before the device is
enumerated. It seems more sensible to only report a "link" if we're
actually connected to a host that wants to talk to us. The patch below
does this for me - tested with the PXA27x UDC driver.
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the ti-usb adapter returns an zero data length frame (which happens)
then we leak a kref.  Found by Christoph Mair <christoph.mair@gmail.com>
who proposed a patch.  The patch here is different as Christoph's patch
didn't work for the case where tty = NULL and data arrived but Christoph
did all the hard work chasing it down.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)

Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
Reported-by: NChuck Ebbert <cebbert@redhat.com>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, the vbus_pin assignment loop is limited by the value of the "ports"
variable in the platform data.  Now that the vbus_pin array is no longer
flexible, we can use its actual size.
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are various bits of code here that are unfinished and instead of
being harmless either confuse or spew stuff into the logs at higher than
debug level. They can and should go away.

Also remove the bogus use of tty->lowlatency. We fixed the need for this hack
long ago (with the flip buffer rewrite) but people keep copying it into drivers.
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Closes bug 9065
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bugzilla #9095 and a couple of other confirmations
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The cdc_acm module is missing the char-major-166-* alias that would
cause it to be auto-loaded when a device of that type is opened.  This
patch adds the alias.
Signed-off-by: NScott James Remnant <scott@canonical.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in.  In particular, all
delayed works which want to rearm themselves will have to do that.  So it
would seem fair to offer a helper function for this operation.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>