Driver would not correctly re-enable the write-protection
bits of the flash part after updates.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:

An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.

Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.

The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.

This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Mailbox commands are polled for completion during ISP
initialization.  During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There's no point in displaying the message during a valid
underrun case.  Limit the message to potentially problematic
cases.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:

We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.

The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.

This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.

The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.

This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:

We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Users can write to a page while we are sending it and making
digest calculations. This ends up causing us to retry the command
when a digest error is later reported. By using sock_no_sendpage
when data digests are calculated we can avoid a lot of (not all but it
helps) the retries becuase sock_no_sendpage is not zero copy.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We should be taking the host_lock instead of the conn lock when
checking host_busy.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We need to check the ISCSI_FLAG_DATA_* flags.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove extra whitespaces.
Signed-off-by: NAlex Aizman <itn780@yahoo.com>
Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead
of semaphores. Untested, but compiles and looks obviously correct.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Now that mptfc actually uses the transport class, it can't be built
without it.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The fix is to write  'MPI_HIM_DIM' to the Host Interrupt Mask
register, when enabling interrupts.  Instead of the
tilde of MPI_HIM_RIM.

Apparently writing '1's to some of the reserved bits was causing
all the bits to go to `1`, which effectly disabled all interrupts.
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We will be mapping the RAID volumes in mptsas to a reserved
channel that
is one larger than the anticapated number of ports on the direct
attached host
adapter.
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This updates mpi headers in fusion drivers to version 1.5.12.
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The SAS RAID volumes are reported beyond the expected number of phys.
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.

When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.

So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning.  As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.

For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add software recognition for the new LSI Logic Fibre Channel controller.
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NMichael Reed <mdr@sgi.com>
Signed-off-by: NEric Moore <Eric.Moore@lsil.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There was a use before initialisation of c->name
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Convert kmalloc + memset to kzalloc or kcalloc in fusion.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Adds hotplug support for SAS end devices.  Unfortunately the fusion
firmware doesn't generate similar events for expanders addition/removal
so we can't support them yet.  Eric has an idea about a clever scheme to
find out about expander changes so that'll be added later on.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The problem in dpt_i2o could be the pci config space accesses it
triggers as it loads, dangerous to do if there is any I/O activity going
on in the other driver (probable if a boot driver I guess).

I approve this patch to dpt_i2o.c, and am applying it to the Adaptec
branch of the driver.

Thanks for the investigation Ryoji.

---

In linux 2.6.15, data transfer does hang when both dpt_i2o
and i2o_block drivers are loaded.
It seems that location of pci_request_regions() are wrong.
I moved it just behind pci_enable_device() like other drivers,
and it becomes fine.
Signed-off-by: NRyoji Kamei <kamei@miraclelinux.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

To avoid the "sda: got wrong page" message, the ServeRAID driver
should be setting flags indicating that the Mode Sense commands are
not supported.
Signed-off-by: NJack Hammer <jack_hammer@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Replaced zfcp adapter attributes with fc_host attributes:
fc_topology by port_type, physical_wwpn by permanent_port_name.
Make use of fc_host attribute supported_speeds.
Removed zfcp adapter attribute physical_s_id.
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Added host stats, removed superfluous get_starget_ functions,
removed some attributes from zfcp specific sysfs tree (e.g.
scsi_host_no, scsi_lun, wwnn and d_id).
Host stats are given for the physical adapter port not for the
virtual adapter. Reset stats is implemented in the device driver.
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Handle unsolicited adapter status that informs about loss of
previous unsolicited status notification(s).
Signed-off-by: NMaxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.

For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

split each ioctl handled in sr_audio_ioctl into a function of it's own.
This cleans the code up nicely, and allows various places in sr_ioctl
to call these helpers directly instead of going through the multiplexer.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code.  There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.

Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We need to iterate over all children when removing and expander, else
stale objects will be around after host removal.  This fixes the oops
Eric Moore saw when removing and reloading mptsas.

Also don't try the scsi_remove_target call unless operating on an end
device.  The current unconditional call is harmless but confusing.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

While trying to get SUSE's SLES9 working on system with more than 4GB we've
noticed that SCSI layer happilly passes addresses over 4GB to the buslogic
driver, which is quite a big problem as buslogic can generate only 32bit
busmastering cycles.

Fortunately in the current kernels this problem does not exist anymore as
SCSI layer now assumes 4GB capable device by default, but it is still good
idea to pass correct device structure to the SCSI layer.  If nothing else,
/sys/block/sda/device now points to
/sys/devices/pci0000:00/0000:00:10.0/host0/...  instead of
/sys/devices/platform/host0/...  like it did in the past.

Change does nothing for ISA based BusLogic adapters, they'll still end
under platform (and they are probably broken for long time as I do not see
anything forcing ISA 16MB limit for them).
Signed-off-by: NPetr Vandrovec <petr@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This takes us past the old 1.x version of the SCSI driver and the 2.x
version of the aic website version to reflect the full incorporation
of both branches.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Update sequencer code to Adaptec version 2.0.12-6.3.9.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>