This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NH.J. Oertel <oe@port.de>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChristian Pellegrin <chripell@fsfe.org>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TI HECC (High End CAN Controller) module is found on many TI devices. It
has 32 hardware mailboxes with full implementation of CAN protocol 2.0B
with bus speeds up to 1Mbps. Specifications of the module are available
on TI web <http://www.ti.com>
Signed-off-by: NAnant Gole <anantgole@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the driver for the SoC CAN controller in Atmel's
AT91SAM9263.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com).
Signed-off-by: NSebastian Haas <haas@ems-wuensche.com>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the generic Socket-CAN driver for the Philips SJA1000
full CAN controller.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.

Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.

For further information please check "Documentation/networking/can.txt"
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the virtual CAN bus (vcan) network driver.
The vcan device is just a loopback device for CAN frames, no
real CAN hardware is involved.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>