Setting .ConfigBase and .Present is now done at the pcmcia core.

The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS.  Setting to
PRESENT_OPTION now overrides the values from the CIS.  So just remove
those lines.
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This changes all HWRNG driver initcalls to module_init().  We must probe
the RNGs after the major kernel subsystems are already up and running (like
PCI).

This fixes Bug 7730.
http://bugzilla.kernel.org/show_bug.cgi?id=7730Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a load option to intel-rng to allow skipping the FWH detection,
necessary in case the BIOS has locked read-only the firmware hub space.
Also prevent any attempt to write to firmware space if it cannot be write
enabled (apparently caused hangs on some systems not having an FWH and thus
also not having a respective RNG).
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix void cast and re-enable on sparc.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds the profile=kvm boot option, which enables KVM to profile VM
exits.

Use: "readprofile -m ./System.map | sort -n" to see the resulting
output:

   [...]
   18246 serial_out                               148.3415
   18945 native_flush_tlb                         378.9000
   23618 serial_in                                212.7748
   29279 __spin_unlock_irq                        622.9574
   43447 native_apic_write                        2068.9048
   52702 enable_8259A_irq                         742.2817
   54250 vgacon_scroll                             89.3740
   67394 ide_inb                                  6126.7273
   79514 copy_page_range                           98.1654
   84868 do_wp_page                                86.6000
  140266 pit_read                                 783.6089
  151436 ide_outb                                 25239.3333
  152668 native_io_delay                          21809.7143
  174783 mask_and_ack_8259A                       783.7803
  362404 native_set_pte_at                        36240.4000
 1688747 total                                      0.5009
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.

Fixing this in raid1 and raid10 seems to be straightforward enough.

For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NLars Ellenberg <lars@linbit.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes the SH rtc driver to
  (a) correctly report 'enabled' status with other alarm status;
  (b) not duplicate that status in its procfs dump
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

While testing 2.6.20-rc3 on a machine with some CK804 chipsets, we noticed
that quirk_nvidia_ck804_msi_ht_cap() was not detecting HT MSI capabilities
anymore.  It is actually caused by the MSI mapping on the root chipset
being the 2nd HT capability in the chain.  pci_find_ht_capability() does
not seem to find anything but the first HT cap correctly, because it
forgets to increment the position before looking for the next cap.  The
following patch seems to fix it.

At least, this proves that having a ttl is good idea since the machine
would have been stucked in an infinite loop if we didn't have a ttl :)

We have to pass pos + PCI_CAP_LIST_NEXT to __pci_find_next_cap_ttl to
get the next HT cap instead of the same one again.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NAndrew J. Gallatin <gallatin@myri.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This reverts commit 2df910b4.

ACPI_BAY has not been merged into mainline yet, so the changes to ibm-acpi
related Kconfig entries that depend on ACPI_BAY were permanently disabling
ibm-acpi bay support.  This is a serious regression for ThinkPad users.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI: Getting cpuindex for acpiid 0x4

acpi_processor-0742 [00] processor_preregister_: Error while parsing _PSD domain information. Assuming no coordination

http://bugzilla.kernel.org/show_bug.cgi?id=7286Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

o MODPOST generates warnings for i386 if kernel is compiled with
  CONFIG_RELOCATABLE=y

WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'

o Two quirk functions which are non __init, are accessing data which is
  of type __init.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
  and serial console support is enabled.

o Serial console setup function, serial8250_console_setup(), is a non __init
  function and it calls functions which are of type __init().
  (uart_parse_options() and uart_set_options()). Assuming, setup will
  be called during init time, changing serial8250_console_setup() to __init.

o Adding one more pattern to modpost whitelist. Console drivers might
  have *_console structures containing references to setup functions which
  can be of __init type. Don't generate warnings for those.

WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Since commit 98e238cd in Linux 2.6.19,
"ieee1394: sbp2: don't prefer MODE SENSE 10", some FireWire DVD-ROMs and
DVD-RWs were mistaken as CD-ROM because sr_mod now sent MODE SENSE 6.
The MMC command set includes only MODE SENSE 10.
http://bugzilla.kernel.org/show_bug.cgi?id=7800

This fix lets sbp2 switch scsi_device.use_10_for_rw on for MMC LUs.
This should rather be done in the command set driver sr_mod, not in the
sbp2 transport driver, and an according patch will follow for a next
Linux release.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

If a QP being queried is in the RESET state, don't execute the
QUERY_QP firmware command (because it will fail).
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Here is a patch for ehca to use proper flag, ie. GFP_ATOMIC
resp. GFP_KERNEL, when calling get_zeroed_page() to prevent "Bug:
scheduling while atomic...". This error does not cause a kernel panic
but makes ipoib un-usable afterwards.  It is reproducible on
2.6.20-rc4 if one does ifconfig down during a flood ping test.  I have
not observed this error in earlier releases incl. 2.6.20-rc1.

This error occurs when a qp event/irq is received and ehca event
handler allocates a control block/page to obtain HCA error data block.
Use of GFP_ATOMIC when in interrupt context prevents this issue.

Signed-off-by Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The sis96x SMBus PCI device depends on two different quirks to run
in a specific order.  Apart from being fragile, this was found to
actually break on (at least) recent FC4, FC5, and FC6 kernels.  This
patch fixes the quirks so that they work without relying on the
compiler and/or linker to put them in any specific order.

  http://lists.lm-sensors.org/pipermail/lm-sensors/2006-April/015962.html
  https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=189719

I tested this patch.
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Greg K-H <greg@kroah.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Changeset 740b5706 moved the protecting
spinlock from __cpcmd to cpcmd. Therefore vmcp can no longer use __cpcmd,
instead we have to use cpcmd.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use barrier() in stsch_reset() instead of duplicating the stsch()
inline assembly and adding "memory" to the clobberlist.
Pointed out by Chuck Ebbert.

Real fix would be to add a fixup section to the stsch() and extend the
basic program check handler so it searches the exception tables in case
of a program check.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Some PHY trim values need to be fine-tuned on 5755M to be
IEEE-compliant.

Update version to 3.72.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 1.5.3.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bug was a bogus pointer being passed to kfree().  The pointer was
incremented in the write loop and then passed to kfree().

The fix is to use align_buf to save the original address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5709 has a new register to detect copper/fiber PHYs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround is only needed on 5706/5708 and cannot be applied on
5709.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCO buffer size values on Dell laptops with a Bluetooth chip from
Broadcom are wrong. The USB Bluetooth driver has to set a quirk to
correct the SCO buffer size values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The SCO buffer size values on HP laptops with a Bluetooth chip from
Broadcom are wrong. The USB Bluetooth driver has to set a quirk to
correct the SCO buffer size values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ThinkPad R60E uses a Broadcom based Bluetooth chip and even this
version needs the quirk to correct the SCO buffer size values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

pcnet_cs: add new id.
 corega K.K. (CG-LAPCCTXD)
 Logitec LPM-LN10TE
Signed-off-by: NKomuro <komurojun-mbn@nifty.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix handling of allocation failure.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

[PATCH 4/5] s390: iucv Kconfig help description changes

From: Ursula Braun <braunu@de.ibm.com>
        remove text from help description which does not
	apply anymore for 2.6 kernel series.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

    - qeth device functions were not callable
      in atomic context due to usage of wait_event_xxx operations in qeth.
      "schedule while atomic" message appeared and kernel dumped when
      removing slave from bond device.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

    - packet socket support is not complete.
      Recvfrom a packet socket does not fill the sockaddr_ll structure.
      device function hard_header_parse is not implemented.
      For layer 2 mode and layer 3 mode with fake_ll turned on, we have
      the information to fill sockaddr_ll.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Ursula Braun <braunu@de.ibm.com>
        - VLAN header reordering did not work on packets
          received through qeth interface in layer 2 mode.
          This caused dhcpcd not to work with VLAN devices.
	- set qeth performance statistics initally inactive
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch contains a fix that implements proper communication with the
sideband management unit. Also, it makes sure that the speed is
correctly set for gigabit phys in the case where sideband mgmt unit
initialized the phy. Refer to bug #7684 for more details.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The MMCI driver might end up aborting the initial command and leaving
the data part of the command sequence still in place.  Avoid this
problem by ensuring that any data sequence is properly cleared out
when a command completes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It would clutter up the kernel output in a situation which is legitimate before
X.org 7.2 and handled correctly by the 3D driver.
Signed-off-by: NDave Airlie <airlied@linux.ie>

According to the Tavor and Arbel programmer's reference manuals, the
number of bytes transferred is not provided in the byte_cnt field of
the CQ entry for atomic operation completions.  For atomic operations,
the number of bytes transferred is always 8 (when the status is
"success"), and this constant value should always be used by the
driver in the ib_wc entry returned, rather than using the CQE.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There's a problem with how rdma cm events are reported to userspace
that can lead to application crashes.

When a new connection request arrives, a context for the connection is
allocated in the kernel.  The connection event is then reported to
userspace.  The userspace library retrieves the event and allocates
its own context for the connection.  The userspace context is
associated with the kernel's context when accepting.  This allows the
kernel to give userspace context with other events.

A problem occurs if a second event for the same connection occurs
before the user has had a chance to call accept.  The userspace
context has not yet been set, which causes the librdmacm to crash.
(This has been seen when the app takes too long to call accept,
resulting in the remote side timing out and rejecting the connection)

Fix this by ignoring events for new connections until userspace has
set their context.  This can only happen if an error occurs on a new
connection before the user accepts it.  This is okay, since the accept
will just fail later.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We discard new connection requests while the listen backlog is full,
but leak a struct ucma_event in the process.  Free the structure in
this case.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The iWARP CM should report timeouts as event RDMA_CM_EVENT_UNREACHABLE,
not event RDMA_CM_EVENT_REJECTED.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>