Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation.  The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.

Here's a good case with the old code (AENs arrive after
mailbox-command completion):

	qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
	qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
	qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
	qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
	qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
	qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
	qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
	qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
	qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
	qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
	qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
	qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315.
	qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
	qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
	qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.

notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.

Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):

	qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
	qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
	qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
	qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
	qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
	qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
	qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
	qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
	qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
	qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
	qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
	qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
	qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2.
	qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
	qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
	qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
	qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
	qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
	qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
	qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.

This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There wasn't any error handling for this kzalloc().
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized.  It's cleaner to just return
directly.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform
after triggering destruct workqueue, but the workqueue will send sync cmd and
still need phy_mask value.  Now, mvsas using asd_sas_phy setting instead of
asd_sas_port setting.
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NMahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Delete successive tests to the same location.  The code tested the result
of a previous allocation, that itself was already tested.  It is changed to
test the result of the most recent allocation.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: NManish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: NManish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.

Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: NPoornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.

Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: NKaren Higgins <karen.higgins@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Removed unnecessary calls to qla4xxx_get_firmware_status from
function qla4xxx_init_local_data
Signed-off-by: NKaren Higgins <karen.higgins@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.

Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When doing a hotplug remove of a cxgb4 device, there are still dandling
symlinks at /sys/class/scsi_host/hostX to the removed PCI device. The
upper layer device may also try to send data, which may crash the
system.

The DETACH message from the lower level driver is sent to the ULD when
the device is removed, when the scsi host should be removed from the
system, avoiding any problems.

After this patch, there are no more dangling symlinks and many attempts
to crash the system while there is SCSI activity and removing the device
have failed. Adding the device back again works as expected, with the
scsi hosts showing up again.

Based on a patch by Karen Xie.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Karen Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The closing parenthesis is in the wrong place so it takes the sizeof a
pointer instead of the sizeof the buffer minus one.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAnil Gurumurthy <agurumur@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Removed use of NOP mailboxes for interrupt verification in pci_probe_one_s4
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>