The SYSFS_DEPRECATED_V2 says "remove" older, deprecated features, but it
actually enables them, so correct this confusing, backwards text.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When detecting power failure, the probe function would reset the clock
time to defined state.

However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.

Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.

The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.

A subsequent probing of the clock fails due to the invalid value range in
the register, though.

[ And if it didn't, reading the clock would yield a bogus year because
  the function translating registers to tm_year is assuming a register
  value of 19 or 20. ]

This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.

Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: NPeter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Remove wrong and unnecessary unmask operation

- Remove extra GEDR reading

This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It has been fun but the last year or more it has been a duty and a burden.
So I leave it open for others to take over.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Anibal Monsalve Salazar <anibal@debian.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Following issues have been addressed on DA8XX/OMAP-L1XX:

a. Screen misalignment during booting when frame buffer console is
   enabled.

b. Driver was configured always in PSEUDOCOLOR mode.  This patch
   dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
   mode depending on bpp.

c. The RED and BLUE offsets were interchanged resulting in wrong
   bootup logo colour.

This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"rtc" is freed and then dereferenced on the next line.  This patch fixes
that.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes:

  v4l/dvb_frontend.c: In function 'dvb_frontend_stop':
  v4l/dvb_frontend.c:707: error: implicit declaration of function 'init_MUTEX'

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14609

Reported-by: <tstrelar@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: update TODO files
  Staging: hv: Fix some missing author names
  Staging: hv: Fix vmbus event handler bug
  Staging: hv: Fix argument order in incorrect memset invocations in hyperv driver.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
  USB: work around for EHCI with quirky periodic schedules
  USB: musb: Fix CPPI IRQs not being signaled
  USB: musb: respect usb_request->zero in control requests
  USB: musb: fix ISOC Tx programming for CPPI DMAs
  USB: musb: Remove unwanted message in boot log
  usb: amd5536udc: fixed shared interrupt bug and warning oops
  USB: ftdi_sio: Keep going when write errors are encountered.
  USB: musb_gadget: fix STALL handling
  USB: EHCI: don't send Clear-TT-Buffer following a STALL

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty/of_serial: add missing ns16550a id
  bcm63xx_uart: Fix serial driver compile breakage.
  tty_port: handle the nonblocking open of a dead port corner case

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Loongson: Switch from flatmem to sparsemem
  MIPS: Loongson: Disallow 4kB pages
  MIPS: Add missing definition for MADV_HWPOISON.
  MIPS: Fix build error if __xchg() is not getting inlined.
  MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.

With flatmem hibernation for Loongson will fail, and there are also some
other problems such as broken files when using NFS or CIFS / Samba.

The config help of sparsemem says:

"This option provides some potential performance benefits, along with
decreased code complexity."

So to avoid the potential problems of FLATMEM, we disable FLATMEM directly
and use SPARSEMEM instead.

Related email thread:

http://groups.google.com/group/loongson-dev/browse_thread/thread/b6b65890ec2b0f24/feb43e5aa7f55d9b?show_docid=feb43e5aa7f55d9bReported-by: NTatu Kilappa <tatu.kilappa@gmail.com>
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/737/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:

Kernel panic - not syncing: Attempted to kill init!

The possible reason is the cache aliases problem:

Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing.  The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes.  So we disable 4kB pages until the aliasing issue is
solved.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/736/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Thanks to Joseph S. Myers for reporting this.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: "Joseph S. Myers" <joseph@codesourcery.com>
Patchwork: http://patchwork.linux-mips.org/patch/723/

If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining.  Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/705/

Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems.  Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot".  Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move slow_work's debugging proc file to debugfs.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Requested-and-acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
  alpha: Fixup last users of irq_chip->typename
  Alpha: Rearrange thread info flags fixing two regressions
  arch/alpha/kernel: Add kmalloc NULL tests
  arch/alpha/kernel/sys_ruffian.c: Use DIV_ROUND_CLOSEST

When IMA is active, using dentry_open without updating the
IMA counters will result in free/open imbalance errors when
fput is eventually called.
Signed-off-by: NMarc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commits 3d7a641e ("SLOW_WORK: Wait for outstanding work items belonging to a
module to clear") introduced some code to make sure that all of a module's
slow-work items were complete before that module was removed, and commit
3bde31a4 ("SLOW_WORK: Allow a requeueable work item to sleep till the thread is
needed") further extended that, breaking it in the process if CONFIG_MODULES=n:

    CC      kernel/slow-work.o
  kernel/slow-work.c: In function 'slow_work_execute':
  kernel/slow-work.c:313: error: 'slow_work_thread_processing' undeclared (first use in this function)
  kernel/slow-work.c:313: error: (Each undeclared identifier is reported only once
  kernel/slow-work.c:313: error: for each function it appears in.)
  kernel/slow-work.c: In function 'slow_work_wait_for_items':
  kernel/slow-work.c:950: error: 'slow_work_unreg_sync_lock' undeclared (first use in this function)
  kernel/slow-work.c:951: error: 'slow_work_unreg_wq' undeclared (first use in this function)
  kernel/slow-work.c:961: error: 'slow_work_unreg_work_item' undeclared (first use in this function)
  kernel/slow-work.c:974: error: 'slow_work_unreg_module' undeclared (first use in this function)
  kernel/slow-work.c:977: error: 'slow_work_thread_processing' undeclared (first use in this function)
  make[1]: *** [kernel/slow-work.o] Error 1

Fix this by:

 (1) Extracting the bits of slow_work_execute() that are contingent on
     CONFIG_MODULES, and the bits that should be, into inline functions and
     placing them into the #ifdef'd section that defines the relevant variables
     and adding stubs for moduleless kernels.  This allows the removal of some
     #ifdefs.

 (2) #ifdef'ing out the contents of slow_work_wait_for_items() in moduleless
     kernels.

The four functions related to handling module unloading synchronisation (and
their associated variables) could be offloaded into a separate .c file, but
each function is only used once and three of them are tiny, so doing so would
prevent them from being inlined.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While building 2.6.32-rc8-git2 for Fedora I noticed the following thinko
in commit 201a1542 ("FS-Cache: Handle
pages pending storage that get evicted under OOM conditions"):

  fs/9p/cache.c: In function '__v9fs_fscache_release_page':
  fs/9p/cache.c:346: error: 'vnode' undeclared (first use in this function)
  fs/9p/cache.c:346: error: (Each undeclared identifier is reported only once
  fs/9p/cache.c:346: error: for each function it appears in.)
  make[2]: *** [fs/9p/cache.o] Error 1

Fix the 9P filesystem to correctly construct the argument to
fscache_maybe_release_page().
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com> [from identical patch]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [from identical patch]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: NMatt Turner <mattst88@gmail.com>

The removal of the TIF_NOTIFY_RESUME flag, commit a583f1b5
"remove unused TIF_NOTIFY_RESUME flag," resulted in incorrect
setting of the unaligned access control flags by the prctl syscall.

The re-addition of the TIF_NOTIFY_RESUME flag, commit d0420c83
"KEYS: Extend TIF_NOTIFY_RESUME to (almost) all architectures [try #6]"
further caused problems, namely incorrect operands to assembler code
as evidenced by:

AS      arch/alpha/kernel/entry.o
arch/alpha/kernel/entry.S: Assembler messages:
arch/alpha/kernel/entry.S:326: Warning: operand out of range
(0x0000000000000406 is not between 0x0000000000000000 and
0x00000000000000ff)

Both regressions fixed by (1) rearranging TIF_NOTIFY_RESUME flag to be
in lower 8 bits of the thread info flags, and (2) making sure that
ALPHA_UAC_SHIFT matches the rearrangement of the thread info flags.
Signed-off-by: NMichael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: David Howells <dhowells@redhat.com>,
Signed-off-by: NMatt Turner <mattst88@gmail.com>

* 'security' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
  mac80211: fix spurious delBA handling
  mac80211: fix two remote exploits

This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).

To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: NGernot Hillier <gernot@hillier.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().

By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.

This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.

Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Signed-off-by: NBabu Ravi <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removes below unnecessary log of almost 28 lines during boot.

musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
...
...
musb_hdrc: hw_ep 13shared, max 4096
musb_hdrc: hw_ep 14shared, max 1024
musb_hdrc: hw_ep 15shared, max 1024
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- fixed shared interrupt bug reported by Vadim Lobanov
 - fixed possible warning oops on driver unload when connected
 - prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
   when using gadget ether
Signed-off-by: NThomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write.  On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.

If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.

Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate().  And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...

While at it, also do the following changes :

- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
  driver does not allow stalling with non-empty Tx FIFO anyway);

- in rxstate(), stop pointlessly zeroing the 'csr' variable;

- in musb_gadget_set_halt(), move the 'done' label to a more proper
  place;

- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1304) fixes a regression in ehci-hcd.  Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.

The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake.  In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found.  In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.

Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests.  Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJavier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove my mail address.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: NHank Janssen <hjanssen@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication.  Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: NHank Janssen <hjanssen@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Nearly every invocation of memset in drivers/staging/hv/StorVsc.c has
its arguments the wrong way around.
Signed-off-by: NDave Jones <davej@redhat.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>