[ Upstream commit 13682e524167cbd7e2a26c5e91bec765f0f96273 ]

When the performance governor is set as default, the rock960 hangs
around one minute after booting, whatever the activity is (idle, key
pressed, loaded, ...).

Based on the commit log found at https://patchwork.kernel.org/patch/10092377/

"vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured."

After removing the vdd-log from the rock960's specific DT, the board
does no longer hang and shows a stable behavior.

Apply the same change for the rock960 by removing the vdd-log from the
DT.

Fixes: 874846f1 ("arm64: dts: rockchip: add 96boards RK3399 Ficus board")
Cc: stable@vger.kernel.org
Tested-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
[sl: adjust filename for 4.19]
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.

This is according to xhci 1.1 specification section 4.23.5.2 extra note:

"Software shall ensure that a device is prevented from entering a U-state
 where its worst case exit latency approaches the ESIT."

Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.

Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.

To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: NShyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: NSandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e46daee53bb50bde38805f1823a182979724c229 upstream.

The arm compiler internally interprets an inline assembly label
as an unsigned long value, not a pointer. As a result, under
CONFIG_FORTIFY_SOURCE, the address of a label has a size of 4 bytes,
which was tripping the runtime checks. Instead, we can just cast the label
(as done with the size calculations earlier).

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1639397Reported-by: NWilliam Cohen <wcohen@redhat.com>
Fixes: 6974f0c4 ("include/linux/string.h: add the option of fortified string.h functions")
Cc: stable@vger.kernel.org
Acked-by: NLaura Abbott <labbott@redhat.com>
Acked-by: NMasami Hiramatsu <mhiramat@kernel.org>
Tested-by: NWilliam Cohen <wcohen@redhat.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 59861547 upstream.

The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list

There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.

cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.

Removing channels from the .pending list solves the problem.

Fixes: 975faaeb ("dma: cppi41: start tear down only if channel is busy")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: NBin Liu <b-liu@ti.com>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 64068853 upstream.

DMA buffer descriptors aren't allocated from atomic context, so they
can use the less heavyweigth GFP_NOWAIT.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRobin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b8603d2a upstream.

The dmaengine documentation states that device_terminate_all may be
asynchronous and need not wait for the active transfers to stop.

This allows us to move most of the functionality currently implemented
in the sdma channel termination function to run in a worker, outside
of any atomic context. Moving this out of atomic context has two
benefits: we can now sleep while waiting for the channel to terminate,
instead of busy waiting and the freeing of the dma descriptors happens
with IRQs enabled, getting rid of a warning in the dma mapping code.

As the termination is now async, we need to implement the
device_synchronize dma engine function which simply waits for the
worker to finish its execution.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRobin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ebb853b1 upstream.

This reverts commit fe5b85c6. The SDMA engine needs the descriptors to
be contiguous in memory. As the dma pool API is only able to provide a
single descriptor per alloc invocation there is no guarantee that multiple
descriptors satisfy this requirement. Also the code in question is broken
as it only allocates memory for a single descriptor, without looking at the
number of descriptors required for the transfer, leading to out-of-bounds
accesses when the descriptors are written.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRobin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c06abca6 upstream.

This reverts commit c1199875, as this depends on another commit
that is going to be reverted.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRobin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ffe843b1 upstream.

Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.

Fix this by partitioning it as 64 bytes per channel.

Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.

Fixes: 199244d6 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8dae5398 upstream.

call_encode can be invoked more than once per RPC call. Ensure that
each call to gss_wrap_req_priv does not overwrite pointers to
previously allocated memory.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Cc: stable@kernel.org
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b4aecf78083d8c6424657c1746c7c3de6e61669f upstream.

Since commit 3b8c9f1c ("arm64: IPI each CPU after invalidating the
I-cache for kernel mappings"), a call to flush_icache_range() will use
an IPI to cross-call other online CPUs so that any stale instructions
are flushed from their pipelines. This triggers a WARN during the
hibernation resume path, where flush_icache_range() is called with
interrupts disabled and is therefore prone to deadlock:

  | Disabling non-boot CPUs ...
  | CPU1: shutdown
  | psci: CPU1 killed.
  | CPU2: shutdown
  | psci: CPU2 killed.
  | CPU3: shutdown
  | psci: CPU3 killed.
  | WARNING: CPU: 0 PID: 1 at ../kernel/smp.c:416 smp_call_function_many+0xd4/0x350
  | Modules linked in:
  | CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc4 #1

Since all secondary CPUs have been taken offline prior to invalidating
the I-cache, there's actually no need for an IPI and we can simply call
__flush_icache_range() instead.

Cc: <stable@vger.kernel.org>
Fixes: 3b8c9f1c ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Reported-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 834e772c8db0c6a275d75315d90aba4ebbb1e249 upstream.

If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible.  This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.

Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu().  This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.

This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".

Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 78b1a52e upstream.

While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432

This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.

Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.

Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Reported-by: NColin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-3-pasic@linux.ibm.com>
Signed-off-by: NCornelia Huck <cohuck@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2448a299ec416a80f699940a86f4a6d9a4f643b1 upstream.

Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().

This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-2-pasic@linux.ibm.com>
Signed-off-by: NCornelia Huck <cohuck@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1e8249b8a4e960018e4baca6b523b8a4500af600 upstream.

Frank Schreiner reported, that since kernel 4.18 he faces sysfs-warnings
when loading modules on a 32-bit kernel. Here is one such example:

 sysfs: cannot create duplicate filename '/module/nfs/sections/.text'
 CPU: 0 PID: 98 Comm: modprobe Not tainted 4.18.0-2-parisc #1 Debian 4.18.10-2
 Backtrace:
  [<1017ce2c>] show_stack+0x3c/0x50
  [<107a7210>] dump_stack+0x28/0x38
  [<103f900c>] sysfs_warn_dup+0x88/0xac
  [<103f8b1c>] sysfs_add_file_mode_ns+0x164/0x1d0
  [<103f9e70>] internal_create_group+0x11c/0x304
  [<103fa0a0>] sysfs_create_group+0x48/0x60
  [<1022abe8>] load_module.constprop.35+0x1f9c/0x23b8
  [<1022b278>] sys_finit_module+0xd0/0x11c
  [<101831dc>] syscall_exit+0x0/0x14

This warning gets triggered by the fact, that due to commit 24b6c225
("parisc: Build kernel without -ffunction-sections") we now get multiple .text
sections in the kernel modules for which sysfs_create_group() can't create
multiple virtual files.

This patch works around the problem by re-enabling the -ffunction-sections
compiler option for modules, while keeping it disabled for the non-module
kernel code.
Reported-by: NFrank Scheiner <frank.scheiner@web.de>
Fixes: 24b6c225 ("parisc: Build kernel without -ffunction-sections")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 48a2ca0ee3994df53da230c7079a18a70ec914f9 upstream.

This reverts commit 3aa2177e.

That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.

Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.

 ------------[ cut here ]------------
 Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
 WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
 Modules linked in: btusb btrtl btintel btbcm bluetooth ...
 CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
 Hardware name: Google Kevin (DT)
 pstate: 40000005 (nZcv daif -PAN -UAO)
 pc : device_release+0x80/0x90
 lr : device_release+0x80/0x90
 sp : ffff00000c47bc70
 x29: ffff00000c47bc70 x28: ffff8000e86b0d40
 x27: 0000000000000000 x26: 0000000000000000
 x25: 0000000056000000 x24: 0000000000000015
 x23: ffff8000f0bbf860 x22: ffff000000d320a0
 x21: ffff8000ee93e100 x20: ffff8000ed931428
 x19: ffff8000ed931418 x18: 0000000000000020
 x17: 0000000000000000 x16: 0000000000000000
 x15: 0000000000000400 x14: 0000000000000143
 x13: 0000000000000000 x12: 0000000000000400
 x11: 0000000000000157 x10: 0000000000000960
 x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
 x7 : 0000000000000000 x6 : ffff8000f7d520b8
 x5 : ffff8000f7d520b8 x4 : 0000000000000000
 x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
 x1 : 37d859939c964800 x0 : 0000000000000000
 Call trace:
  device_release+0x80/0x90
  kobject_put+0x74/0xe8
  device_unregister+0x20/0x30
  ec_device_remove+0x34/0x48 [cros_ec_dev]
  platform_drv_remove+0x28/0x48
  device_release_driver_internal+0x1a8/0x240
  driver_detach+0x40/0x80
  bus_remove_driver+0x54/0xa8
  driver_unregister+0x2c/0x58
  platform_driver_unregister+0x10/0x18
  cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
  __arm64_sys_delete_module+0x16c/0x1f8
  el0_svc_common+0x84/0xd8
  el0_svc_handler+0x2c/0x80
  el0_svc+0x8/0xc
 ---[ end trace a57c4625f3c60ae8 ]---

Cc: stable@vger.kernel.org
Fixes: 3aa2177e ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>
Reviewed-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3420f65cbbd0555049bd02394bed33a0ef74d860 upstream.

The dvb_frontend core already checks for the frequencies. No
need for any additional check inside the driver.

It is part of the fixes for the following bug:
  https://bugzilla.opensuse.org/show_bug.cgi?id=1116374

Fixes: a3f90c75 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: NStakanov Schufter <stakanov@eclipso.eu>
Reported-by: NTakashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d8e450f517cdb33da77827ec75929354753e9c0 upstream.

Tuners should report frequencies in Hz. That works fine on most
drivers, but, in the case of dvb-pll, some settings are for
satellite tuners, while others are for terrestrial/cable ones.

The code was trying to solve it at probing time, but that doesn't
work, as, when _attach is called, the delivery system may be wrong.

Fix it by ensuring that all frequencies are in Hz at the per-tuner
max/min values.

While here, add a debug message, as this would help to debug any
issues there.

It partially fixes the following bug:
  https://bugzilla.opensuse.org/show_bug.cgi?id=1116374

Fixes: a3f90c75 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: NStakanov Schufter <stakanov@eclipso.eu>
Reported-by: NTakashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cb3b2ffb757e75fef40fb94bc093cbbf49a6bf6e upstream.

The size passed to memchr is too large as it assumes the search
starts at the start of the buffer, but it can start at an offset.

Cc: <stable@vger.kernel.org>      # for v4.19 and up
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f96d84488f7d5f9123428c700cea82a292bca53e upstream.

When converting gspca to vb2 I missed that fact that the buffer sizes
were rounded up to the next page size. As a result some gspca drivers
(spca561 being one of them) reported frame overflows.

Modify the code to align the buffer sizes to the next page size, just
as the original code did.

Fixes: 1f5965c4 ("media: gspca: convert to vb2")
Tested-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: Nsoftwarebugs <softwarebugs@protonmail.com>
Cc: <stable@vger.kernel.org>      # for v4.18 and up
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b72f936f6b325f4fde06b02e4b6ab682f6f2e73f upstream.

Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NChris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9f8aefed9623a91dec54eab8908f3810b7f8d73a upstream.

Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NChris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 705b65f107470499442240ff7afee5021a7002a6 upstream.

The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NChris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 33aaebd48ae2d2c78fef5063a0381e17db19b060 upstream.

Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.

Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NChris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 54947cd64c1b8290f64bb2958e343c07270e3a58 upstream.

We've got a regression report for some Thinkpad models (at least
T570s) which shows the too low speaker output volume.  The bisection
leaded to the commit 61fcf8ec ("ALSA: hda/realtek - Enable Thinkpad
Dock device for ALC298 platform"), and it's basically adding the two
pin configurations for the dock, and looks harmless.

The real culprit seems, though, that the DAC assignment for the
speaker pin is implicitly assumed on these devices, i.e. pin NID 0x14
to be coupled with DAC NID 0x03.  When more pins are configured by the
commit above, the auto-parser changes the DAC assignment, and this
resulted in the regression.

As a workaround, just provide the fixed pin / DAC mapping table for
this Thinkpad fixup function.  It's no generic solution, but the
problem itself is pretty much device-specific, so must be good
enough.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1554304
Fixes: 61fcf8ec ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: NJeremy Cline <jcline@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5363857b916c1f48027e9b96ee8be8376bf20811 upstream.

As addressed in alsa-lib (commit b420056604f0), we need to fix the
case where the evaluation of PCM interval "(x x+1]" leading to
-EINVAL.  After applying rules, such an interval may be translated as
"(x x+1)".

Fixes: ff2d6acd ("ALSA: pcm: Fix snd_interval_refine first/last with open min/max")
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b51abed8355e5556886623b2772fa6b7598d2282 upstream.

Currently the PCM core calls snd_pcm_unlink() always unconditionally
at closing a stream.  However, since snd_pcm_unlink() invokes the
global rwsem down, the lock can be easily contended.  More badly, when
a thread runs in a high priority RT-FIFO, it may stall at spinning.

Basically the call of snd_pcm_unlink() is required only for the linked
streams that are already rare occasion.  For normal use cases, this
code path is fairly superfluous.

As an optimization (and also as a workaround for the RT problem
above in normal situations without linked streams), this patch adds a
check before calling snd_pcm_unlink() and calls it only when needed.
Reported-by: NChanho Min <chanho.min@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b888a5f713e4d17faaaff24316585a4eb07f35b7 upstream.

Commit 67ec1072 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM
stream") fixes deadlock for non-atomic PCM stream. But, This patch
causes antother stuck.
If writer is RT thread and reader is a normal thread, the reader
thread will be difficult to get scheduled. It may not give chance to
release readlocks and writer gets stuck for a long time if they are
pinned to single cpu.

The deadlock described in the previous commit is because the linux
rwsem queues like a FIFO. So, we might need non-FIFO writelock, not
non-block one.

My suggestion is that the writer gives reader a chance to be scheduled
by using the minimum msleep() instaed of spinning without blocking by
writer. Also, The *_nonblock may be changed to *_nonfifo appropriately
to this concept.
In terms of performance, when trylock is failed, this minimum periodic
msleep will have the same performance as the tick-based
schedule()/wake_up_q().

[ Although this has a fairly high performance penalty, the relevant
  code path became already rare due to the previous commit ("ALSA:
  pcm: Call snd_pcm_unlink() conditionally at closing").  That is, now
  this unconditional msleep appears only when using linked streams,
  and this must be a rare case.  So we accept this as a quick
  workaround until finding a more suitable one -- tiwai ]

Fixes: 67ec1072 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM stream")
Suggested-by: NWonmin Jung <wonmin.jung@lge.com>
Signed-off-by: NChanho Min <chanho.min@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3deef52ce10514ccdebba8e8ab85f9cebd0eb3f7 upstream.

It's similar to other AMD audio devices, it also supports D3, which can
save some power drain.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5f8cf712582617d523120df67d392059eaf2fc4b upstream.

If a USB sound card reports 0 interfaces, an error condition is triggered
and the function usb_audio_probe errors out. In the error path, there was a
use-after-free vulnerability where the memory object of the card was first
freed, followed by a decrement of the number of active chips. Moving the
decrement above the atomic_dec fixes the UAF.

[ The original problem was introduced in 3.1 kernel, while it was
  developed in a different form.  The Fixes tag below indicates the
  original commit but it doesn't mean that the patch is applicable
  cleanly. -- tiwai ]

Fixes: 362e4e49 ("ALSA: usb-audio - clear chip->probing on error exit")
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: NHui Peng <benquike@gmail.com>
Signed-off-by: NMathias Payer <mathias.payer@nebelwelt.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 44ff57e685f96d0cb9540004cc9d1d880e7a4315 upstream.

This patch adds quirk VID/PID IDs for the SMSL D1 in order to enable
Native DSD support.

[ Moved the added entry in numerical order -- tiwai ]
Signed-off-by: NTony Das <tdas444@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f51ccf46 upstream.

The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.

Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.

Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().

Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.

This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).

Fixes: 7041d9c3 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org>	# 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NHui Peng <benquike@gmail.com>
Signed-off-by: NMathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d7859905301880ad3e16272399d26900af3ac496 upstream.

Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: NAlexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.

Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.

i.e.,
[  166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[  166.918327] usb usb2-port2: link state change
[  166.918337] usb usb2-port2: do warm reset
[  166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[  167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[  167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[  167.276050] usb 2-2: USB disconnect, device number 2
[  167.276058] usb 2-2: unregistering device
[  167.276060] usb 2-2: unregistering interface 2-2:1.0
[  167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[  167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...

Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.

Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.

The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: NHarry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c44c749d3b6fdfca39002e7e48e03fe9f9fe37a3 ]

of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5ed9dc99107144f83b6c1bb52a69b58875baf540 ]

team_notify_peers() will send ARP and NA to notify peers. team_mcast_rejoin()
will send multicast join group message to notify peers. We should do this when
enabling/changed to a new port. But it doesn't make sense to do it when a port
is disabled.

On the other hand, when we set mcast_rejoin_count to 2, and do a failover,
team_port_disable() will increase mcast_rejoin.count_pending to 2 and then
team_port_enable() will increase mcast_rejoin.count_pending to 4. We will send
4 mcast rejoin messages at latest, which will make user confused. The same
with notify_peers.count.

Fix it by deleting team_notify_peers() and team_mcast_rejoin() in
team_port_disable().
Reported-by: NLiang Li <liali@redhat.com>
Fixes: fc423ff0 ("team: add peer notification")
Fixes: 492b200e ("team: add support for sending multicast rejoins")
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5bf032ef08e6a110edc1e3bfb3c66a208fb55125 ]

During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b7cdec3d699db2e5985ad39de0f25d3b6111928e ]

The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>