Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables flow control to be set in SerDes autoneg mode.  This is
done the way it is done for copper, but relies on a different set of register/bit
checks since this is all done within the MAC registers.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch unsets the sigdetect bit for SERDES loopback tests on 82580 and
i350 parts.  The loopback test can fail on these parts without this
setting.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to a hw errata, the global device reset doesn't always work on 82580
devices.  This patch works around the problem not trying to do a global
device reset on these devices.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors the functions in e1000_i210.c in order to remove need
for prototypes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows software acquires and releases NVM resource for
writing each EEPROM page, instead of holding semaphore for the whole
data block which is too long and could trigger write fails on
unpredictable addresses.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i211 has an integrated secure space to store configuration information that is
usually stored in an EEPROM or flash type device. This patch updates the
read functions to return values or appropriate error codes to prevent
unnecessary init failures on some configuration schemes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces calls to copy_to_user, copy_from_user, and the associated
logic, with calls to simple_read_from_buffer and simple_write_to_buffer
respectively.  This was done to eliminate warnings generated by the Smatch
static analysis tool.

v2- Fix return values based community feedback
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Unlike LRO, GRO requires that vlan tags be removed before
aggregation can occur.  Since the myri10ge NIC does not support
hardware vlan tag offload, we must remove the tag in the driver
to achieve performance comparable to LRO for vlan tagged frames.

Thanks to Eric Duzamet for his help simplifying the original patch.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert myri10ge from LRO to GRO, and simplify the driver by removing
various LRO-related code which is no longer needed including
ndo_fix_features op, custom skb building from frags, and LRO
header parsing.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delivery to the following recipient failed permanently:

     vtun@office.satix.net

Technical details of permanent failure:
DNS Error: Domain name not found

Of course:
$ host office.satix.net
Host office.satix.net not found: 3(NXDOMAIN)

===========

And "Change of Email Address Notification":
Old Address        New Address           Email Subject
------------------------------------------------------
maxk@qualcomm.com  maxk@qti.qualcomm.com "tuntap: multiqueue...
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These macros, while reducing the amount of code, hide flow control
and make the code more confusing to follow and review.  This patch
expands them.  It should have no functional effect on the driver.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug introduced in bbd9f9ee which could prevent
some wakeups from working correctly if multiple wol options were
selected.

This helper function calculates a 16-bit crc and shifts it into
either the high or low 16 bits of a u32 so the caller can or it
directly into place.  The function previously had a u16 return
type so would always have returned zero when filter was odd.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Reported-by: NBjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch ensures that if we fail to suspend the LAN9500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a buffer overflow introduced by bbd9f9ee, where
the filter_mask array is accessed beyond its bounds.

Updated to also add a check for kzalloc failure, as reported by
Bjorn Mork and Joe Perches.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These macros, while reducing the amount of code, hide flow control
and make the code more confusing to follow and review.  This patch
expands them.  It should have no functional effect on the driver.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If usbnet_suspend returns an error we don't want to call
usbnet_resume to clean up, but instead just return the error.

If usbnet_suspend *does* succeed, and we have a problem further
on, the desired behaviour is still to call usbnet_resume
to clean up before returning.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the variable parameter length provided in the mandatory
heartbeat information parameter exceeds the calculated payload
length the packet has been corrupted. Reply with a parameter
length protocol violation message.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes an unused parameter (src_net) from rtnl_create_link()
method and from the method single invocation, in veth.
This parameter was used in the past when calling
ops->get_tx_queues(src_net, tb) in rtnl_create_link().
The get_tx_queues() member of rtnl_link_ops was replaced by two methods,
get_num_tx_queues() and get_num_rx_queues(), which do not get any
parameter. This was done in commit d40156aa by
Jiri Pirko ("rtnl: allow to specify different num for rx and tx queue count").
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Included changes:
- Use the new ETH_P_BATMAN define instead of the private BATADV_ETH_P_BATMAN
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trinity (the syscall fuzzer) triggered the following BUG, reproducible
only when the kernel is configured with CONFIG_SCTP_DBG_MSG=y.

When CONFIG_SCTP_DBG_MSG is not set, the null pointer is never
dereferenced.

---[ end trace a4de0bfcb38a3642 ]---
BUG: unable to handle kernel NULL pointer dereference at 0000000000000100
IP: [<ffffffff8136796e>] ip6_string+0x1e/0xa0
PGD 4eead067 PUD 4e472067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in:
CPU 3
Pid: 21324, comm: trinity-child11 Tainted: G        W    3.7.0-rc7+ #61 ASUSTeK Computer INC. EB1012/EB1012
RIP: 0010:[<ffffffff8136796e>]  [<ffffffff8136796e>] ip6_string+0x1e/0xa0
RSP: 0018:ffff88004e4637a0  EFLAGS: 00010046
RAX: ffff88004e4637da RBX: ffff88004e4637da RCX: 0000000000000000
RDX: ffffffff8246e92a RSI: 0000000000000100 RDI: ffff88004e4637da
RBP: ffff88004e4637a8 R08: 000000000000ffff R09: 000000000000ffff
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff8289d600
R13: ffffffff8289d230 R14: ffffffff8246e928 R15: ffffffff8289d600
FS:  00007fed95153700(0000) GS:ffff88005fd80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000100 CR3: 000000004eeac000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process trinity-child11 (pid: 21324, threadinfo ffff88004e462000, task ffff8800524b0000)
Stack:
 ffff88004e4637da ffff88004e463828 ffffffff81368eee 000000004e4637d8
 ffffffff0000ffff ffff88000000ffff 0000000000000000 000000004e4637f8
 ffffffff826285d8 ffff88004e4637f8 0000000000000000 ffff8800524b06b0
Call Trace:
 [<ffffffff81368eee>] ip6_addr_string.isra.11+0x3e/0xa0
 [<ffffffff81369183>] pointer.isra.12+0x233/0x2d0
 [<ffffffff810a413a>] ? vprintk_emit+0x1ba/0x450
 [<ffffffff8110953d>] ? trace_hardirqs_on_caller+0x10d/0x1a0
 [<ffffffff81369757>] vsnprintf+0x187/0x5d0
 [<ffffffff81369c62>] vscnprintf+0x12/0x30
 [<ffffffff810a4028>] vprintk_emit+0xa8/0x450
 [<ffffffff81e5cb00>] printk+0x49/0x4b
 [<ffffffff81d17221>] sctp_v6_get_dst+0x731/0x780
 [<ffffffff81d16e15>] ? sctp_v6_get_dst+0x325/0x780
 [<ffffffff81d00a96>] sctp_transport_route+0x46/0x120
 [<ffffffff81cff0f1>] sctp_assoc_add_peer+0x161/0x350
 [<ffffffff81d0fd8d>] sctp_sendmsg+0x6cd/0xcb0
 [<ffffffff81b55bf0>] ? inet_create+0x670/0x670
 [<ffffffff81b55cfb>] inet_sendmsg+0x10b/0x220
 [<ffffffff81b55bf0>] ? inet_create+0x670/0x670
 [<ffffffff81a72a64>] ? sock_update_classid+0xa4/0x2b0
 [<ffffffff81a72ab0>] ? sock_update_classid+0xf0/0x2b0
 [<ffffffff81a6ac1c>] sock_sendmsg+0xdc/0xf0
 [<ffffffff8118e9e5>] ? might_fault+0x85/0x90
 [<ffffffff8118e99c>] ? might_fault+0x3c/0x90
 [<ffffffff81a6e12a>] sys_sendto+0xfa/0x130
 [<ffffffff810a9887>] ? do_setitimer+0x197/0x380
 [<ffffffff81e960d5>] ? sysret_check+0x22/0x5d
 [<ffffffff81e960a9>] system_call_fastpath+0x16/0x1b
Code: 01 eb 89 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 f8 31 c9 48 89 e5 53 eb 12 0f 1f 40 00 48 83 c1 01 48 83 c0 04 48 83 f9 08 74 70 <0f> b6 3c 4e 89 fb 83 e7 0f c0 eb 04 41 89 d8 41 83 e0 0f 0f b6
RIP  [<ffffffff8136796e>] ip6_string+0x1e/0xa0
 RSP <ffff88004e4637a0>
CR2: 0000000000000100
---[ end trace a4de0bfcb38a3643 ]---
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kfree_skb() indicates failure, which is where this is being used.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kfree_skb() was not getting called in the case of some failures.
This was pointed out by Eric Dumazet.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the threshold for framentation of a lowpan packet from
using the MTU size to now use the MTU size minus the checksum length,
which is added by the hardware. For IEEE 802.15.4, this effectively
changes it from 127 bytes to 125 bytes.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this pull request is for net-next/master. There is a patch by Alexander
Stein fixing a reference counter problem which can make driver
unloading impossible (stable Cc'ed). And several patches by me which
remove an obsolete mechanism from several drivers, which is already
handled at the infrastructure level.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves bitops usages in several points:

- Convert u64 to a proper bitmap declaration.  This enables to remove
  superfluous typecasting from 'u64' to 'unsigned long *'.

- Convert superfluous atomic bitops to non atomic bitops.  The bitmap
  is allocated on the stack and it is not accessed by any other threads,
  so using atomic bitops is not necessary.

- Use find_next_zero_bit and find_next_zero_bit instead of calling
  test_bit() for each bit.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bug is observed on running FCoE over a VLAN device associated w/
a real device that has IFF_UNICAST_FLT set since FCoE would add unicast
address such as FLOGI MAC to the VLAN interface that FCoE is on. Since
currently, VLAN device is not inheriting the IFF_UNICAST_FLT flag from the
parent real device even though the real device is capable of doing unicast
filtering. This forces the VLAN device and its real device go to promiscuous
mode unnecessarily even the added address is actually being added to the
available unicast filter table in real device.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Cc: devel@open-fcoe.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding in balance-alb mode records information from ARP packets
passing through the bond in a hash table (rx_hashtbl).

At certain situations (e.g. link change of a slave),
rlb_update_rx_clients() will send out ARP packets to update ARP
caches of other hosts on the network to achieve RX load
balancing.

The problem is that once an IP address is recorded in the hash
table, it stays there indefinitely. If this IP address is
migrated to a different host in the network, bonding still sends
out ARP packets that poison other systems' ARP caches with
invalid information.

This patch solves this by looking at all incoming ARP packets,
and checking if the source IP address is one of the source
addresses stored in the rx_hashtbl. If it is, but the MAC
addresses differ, the corresponding hash table entries are
removed. Thus, when an IP address is migrated, the first ARP
broadcast by its new owner will purge the offending entries of
rx_hashtbl.

The hash table is hashed by ip_dst. To be able to do the above
check efficiently (not walking the whole hash table), we need a
reverse mapping (by ip_src).

I added three new members in struct rlb_client_info:
   rx_hashtbl[x].src_first will point to the start of a list of
      entries for which hash(ip_src) == x.
   The list is linked with src_next and src_prev.

When an incoming ARP packet arrives at rlb_arp_recv()
rlb_purge_src_ip() can quickly walk only the entries on the
corresponding lists, i.e. the entries that are likely to contain
the offending IP address.

To avoid confusion, I renamed these existing fields of struct
rlb_client_info:
	next -> used_next
	prev -> used_prev
	rx_hashtbl_head -> rx_hashtbl_used_head

(The current linked list is _not_ a list of hash table
entries with colliding ip_dst. It's a list of entries that are
being used; its purpose is to avoid walking the whole hash table
when looking for used entries.)
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not modify or load balance ARP packets passing through balance-alb
mode (wherein the ARP did not originate locally, and arrived via a bridge).

Modifying pass-through ARP replies causes an incorrect MAC address
to be placed into the ARP packet, rendering peers unable to communicate
with the actual destination from which the ARP reply originated.

Load balancing pass-through ARP requests causes an entry to be
created for the peer in the rlb table, and bond_alb_monitor will
occasionally issue ARP updates to all peers in the table instrucing them
as to which MAC address they should communicate with; this occurs when
some event sets rx_ntt.  In the bridged case, however, the MAC address
used for the update would be the MAC of the slave, not the actual source
MAC of the originating destination.  This would render peers unable to
communicate with the destinations beyond the bridge.
Signed-off-by: NZheng Li <zheng.x.li@oracle.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv6/exthdrs_core.c

Jesse Gross says:

====================
This series of improvements for 3.8/net-next contains four components:
 * Support for modifying IPv6 headers
 * Support for matching and setting skb->mark for better integration with
   things like iptables
 * Ability to recognize the EtherType for RARP packets
 * Two small performance enhancements

The movement of ipv6_find_hdr() into exthdrs_core.c causes two small merge
conflicts.  I left it as is but can do the merge if you want.  The conflicts
are:
 * ipv6_find_hdr() and ipv6_find_tlv() were both moved to the bottom of
   exthdrs_core.c.  Both should stay.
 * A new use of ipv6_find_hdr() was added to net/netfilter/ipvs/ip_vs_core.c
   after this patch.  The IPVS user has two instances of the old constant
   name IP6T_FH_F_FRAG which has been renamed to IP6_FH_F_FRAG.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

This patch changes three methods to be static and removes their
EXPORT_SYMBOLs in core/dev.c and their external declaration in
netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and
napi_skb_finish(), which are in the GRO rx path, are not used
outside core/dev.c.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the description of how tcp_ecn works a bit more explicit and clear.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable open_time in the struct peak_usb_device was used to protect
peak_usb_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The variable open_time in the struct esd_usb2_net_priv was used to protect
esd_usb2_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The variable open_time in the struct ems_usb was used to protect
ems_usb_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The variable open_time in the struct sja1000_priv was used to protect
sja1000_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The variable open_time in the struct mscan_priv was used to protect
mscan_do_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>