Many regulator drivers implement voltage setting by looping through a
table of possible values, normally because the set of available voltages
can't be mapped onto selectors with simple calcuation. Factor out these
loops by providing a variant of set_voltage() which takes a selector rather
than a voltage range as an argument and implementing a loop through the
available selectors in the core.

This is not going to be suitable for use with all devices as when the
regulator voltage can be mapped onto selector values with a simple
calculation the linear scan through the available values will be more
expensive than just doing the calculation, especially for regulators
that provide fine grained voltage control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Push all the callers of the chip set_voltage() operation out into a single
function to facilitiate future refactoring.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

add support for mc13892, tested on mx51 babbage board
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch removes the macros for initializing the regulators.
The purpose is to remove one layer of abstraction and make the
code easier to read.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The verbose debug outputs register writes and reads that can be
used to debug the driver.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Error handling is updated to catch NULL pointer errors.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The regulator enumeration is used for putting the regulator data
in correct place in the info array. This should be matched in the
board configuration.

Variable names are updated to be more consistent, comments are
corrected and macros have been edited to be consistent.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The AUX3 regulator voltage setting is changed in ab8500 v2 compared
to ab8500 v1. This patch adds v2 support while keeping support for
v1.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The find_regulator function was unused so it has been removed. The
ab8500 pointer in the regulator info structure was unused and so it
has also been removed.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

For INTCORE and TVOUT regulators, the low power register bit is
included in the mask so that enable will set the regulator in
normal (high power) mode.

ANAMIC1, ANAMIC2, DMIC regulator settings are swapped with each
other so that the correct regulator gets enabled/disabled.

ANA regulator register address is corrected.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The define for number of regulators is moved from ab8500-core to
ab8500-regulator so that the regulator driver can be updated
independently of ab8500-core. This also changes the platform
configuration structure of ab8500-core so that it contains a
pointer to the regulator_init_data array plus number of
regulators instead of an fixed size array of pointers to
regulator_init_data.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators.  This device is interfaced using SPI.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Since drivers already have to provide an API for translating selectors
into voltages they may as well just report the selector values directly
to the core API rather than implement the lookup themselves. The old
interface is left in place for now, but may be removed in future.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Rather than referencing the get_voltage() operation directly in the
ops struct use the internal _regulator_get_voltage() API call to do
so, facilitating refactoring.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Align arguments.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Extend the regulator_set_voltage() function to take into account the
voltage requirements of all consumers of the regulator being changed,
in order to set the voltage to the minimum voltage acceptable to all
consumers. The existing behaviour was that the latest
regulator_set_voltage() call would win over previous
regulator_set_voltage() calls even if setting the voltage to a
non-acceptable level from other consumers.
Signed-off-by: NThomas Petazzoni <t-petazzoni@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

On Tue, 2010-11-30 at 10:52 +0000, Mark Brown wrote:
> On Mon, Nov 29, 2010 at 05:12:56PM -0800, Joe Perches wrote:
> > Just to please broonie...
> > Signed-off-by: Joe Perches <joe@perches.com>
> As usual when fixing review issues please revise your original patch
> rather than posting a fresh patch.

Here's an earlier comment:

On Thu, 2010-11-18 at 13:30 +0000, Mark Brown wrote:
> This looks reasonable, please rebase on top of Daniel's patches and
> submit it properly (with changelog and so on).

Sometimes it's simpler for an upstream maintainer to do
something like:

git am -s <patch1.mbox>
patch -p1 < patch2.mbox
git commit --amend file

instead of back and forthing.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

They're not needed and sparse is verbosely upset about them.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently the regulator API uses the constraints structure passed in to
the core throughout the lifetime of the object. This means that it is not
possible to mark the constraints as __initdata so if the kernel supports
many boards the constraints for all of them are kept around throughout the
lifetime of the system, consuming memory needlessly. By copying constraints
that are actually used we allow the use of __initdata, saving memory when
multiple boards are supported.

This also means the constraints can be const.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The version hasn't been updated since the regulator API was merged in
2.6.27 so just remove it - now we're in mainline the kernel version is
much more useful.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Don't use %s to format fixed static strings into log messages, it just
makes searching for and reading the message in the kernel source
needlessly hard.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The regulator framework uses a lot of printks with a
specific formatting using __func__. This converts them
to use pr_ calls with a central format string.

Cc: bleong@codeaurora.org
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This adds a pr_fmt line which uses the __func__ macro. I also
convert the current pr_ lines to remove their __func__ usage.

Cc: bleong@codeaurora.org
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Provide some basic trace facilities to the regulator API. We generate
events on regulator enable, disable and voltage setting over the actual
hardware operations (which are assumed to be the expensive ones which
require interaction with the actual device). This is intended to facilitate
debug of the performance and behaviour with consumers allowing unified
traces to be generated including the regulator operations within the
context of the other components of the system.

For enable we log the explicit delay for the voltage ramp separately to
the interaction with the hardware to highlight the time consumed in I/O.
We should add a similar delay for voltage changes, though there the
relatively small magnitude of the changes in the context of the I/O
costs makes it much less critical for most regulators.

Only hardware interactions are currently traced as the primary focus is
on the performance and synchronisation of actual hardware interactions.
Additional tracepoints for debugging of the logical operations can be
added later if required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change the interface used by set_voltage() to report the selected value
to the regulator core in terms of a selector used by list_voltage().
This allows the regulator core to know the voltage that was chosen
without having to do an explict get_voltage(), which would be much more
expensive as it will generally access hardware.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch add locks around regulator supply enable.
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Correct the register table for SM2, LDO8, RTC

Change-Id: I45348cec5ffbb7da9bd7523764fb611b537236b8
Signed-off-by: NDanny Huang <dahuang@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change-Id: I40400bb65eab496bb1becd26b37a9653b99d4f41
Signed-off-by: NDanny Huang <dahuang@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
  (Split into separate patches)
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change-Id: Idacf5e1e51dbbbcd5ea93f310a4e907977e7359e
Signed-off-by: NDanny Huang <dahuang@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
  (Split into separate patches)
  (Minor formatting fixes)
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change-Id: I76eaceb31b56264f6978af15db1e6fc7e2e01b5a
Signed-off-by: NDanny Huang <dahuang@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
  (Split into separate patches)
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Fix kernel-doc warning for set_consumer_device_supply():

Warning(drivers/regulator/core.c:912): missing initial short description on line:
 * set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc:	Liam Girdwood <lrg@slimlogic.co.uk>
Cc:	Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>