Wolfram Sang pointed out during review of an efm32-i2c driver that the
property to specify the set of pins has a too general name. As several
other efm32 peripherals also have a similar register bit field, add an
"efm32" namespace.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

While removing the 0x prefixes in the unit addresses in reply to a review
comment, I must somehow have messed up these two. Uups.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device nodes for OMAP443x family of devices. abb_iva is
populated, but disabled as it is not used on current OMAP443x family,
but the node is used on OMAP446x family. Data is based on OMAP443x
Technical Reference Manual revision AN (April 2013).

ABB device nodes for OMAP4460 device Data is based on OMAP4460
Technical Reference Manual revision Z (April 2013)

[nm@ti.com: co-developer]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NAndrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device node for OMAP36xx family of devices. Data is based on
OMAP36XX Technical Reference Manual revision AB (Dec 2012).

[nm@ti.com: co-developer]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NAndrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

enable sd card slot on am437x-gp-evm
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added device tree bindings for dwc3, usb2 and usb3 PHYs. The documentation
of these can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt
and Documentation/devicetree/bindings/phy/ti-phy.txt.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The BCM11351 BRT board will never see the light of day. Remove the BRT
dts since it is not maintainable.
Reviewed-by: NAlex Elder <elder@linaro.org>
Reviewed-by: NChristian Daudt <bcm@fixthebug.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

Enable the WiLink6 connected to mmc2.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix DuoVero is an OMAP4430-based Computer On Module.
Parlor is one of the available expansion board.

Tested features:
- GPMC ethernet
- HSUSB2 and OTG
- Audio out
- WiFi and Bluetooth (w2cbw0015 SDIO module)
- LED and button
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Describe the T5325 using device tree properties, where possible.  The
first version of this file was produced by Thomas Petazzoni.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The binding has existed for a while, so add the missing node so it can
be used by devices.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With kirkwood migrating into mach-mvebu, mvebu_v5_defconfig needs to
select ARCH_MVEBU.  Unfortunately, this means that when building a v5
kernel, we unnecessarily build dtbs for the armada v7 boards.

To fix this, we instead select based on MACH_ARMADA_* on a per SoC basis.
Reported-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

We share global config registers by syscon node, add it to dove.dtsi.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Dove pinctrl uses additional registers to control MPPs. This patch first
increases existing pinctrl reg property by one register, and then adds
two new ranges for MPP4 and PMU MPP registers.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Make use of the mvebu system controller, by placing a node into the
dtsi file.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the Feroceon L2 cache has a DT binding, make use of it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.

Add documentation for the DMM bindings.

Originally worked on by Andy Gross <andygro@gmail.com>

Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add gpio keys node for am43x gp evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
    Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch has following updates, specific to MTD/NAND DT
 - update MTD NAND partition table to keep compatibility between
   different boards and mainline u-boot.
 - prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
   from other MTD device partitions (like NOR and QSPI)
               Partition_Name            Partition_Size
    /dev/mtd0  NAND.SPL                  1 block-size*
    /dev/mtd1  NAND.SPL.backup1          1 block-size*
    /dev/mtd2  NAND.SPL.backup2          1 block-size*
    /dev/mtd3  NAND.SPL.backup3          1 block-size*
    /dev/mtd5  NAND.u-boot-spl-os        2 block-size* [for falcon boot]
    /dev/mtd4  NAND.u-boot               1 MB
    /dev/mtd6  NAND.u-boot-env           1 block-size*
    /dev/mtd7  NAND.u-boot-env.backup1   1 block-size*
    /dev/mtd8  NAND.kernel               till 0xA00000
    /dev/mtd9  NAND.file-system          till end of device

* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for bma180 driver.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This requires vaux4.

Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds basic sound support for gta04 board.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define twl4030 charger node used for charging.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add magnetometer hmc5843 node.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for gp evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add SPI dts data.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add I2C2 dts data.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for am43x epos evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>