We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere.  In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.

Remove the color increment to use always zero and avoid reaching 255.

CC: <stable@vger.kernel.org> [3.10+]
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's really no reason to pad out the field with spaces at the
end of the line - they're practically invisible there anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If we don't want to restart the firmware, don't reprobe either in case
of a failure during reconfiguration.  This allows us to debug failures
in the reconfig flow as well.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

IWL_UCODE_TLV_API_SCD_CFG is a new API and hence, check if
enabled in the correct field.

Fixes: 0294d9ee ("iwlwifi: mvm: let the firmware configure the scheduler")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the PHY_CTXT command sent to the FW the TX chains were
indeed configured by the values of both FW TLVs and of NVM,
but the RX chains were left out and configured only by FW
TLV.

This causes problems in 4165 HW, where there are 1x1
antennas, and the wrong configuration denies the driver
from connecting to the AP.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The stats argument is always only passed as &mvm->drv_rx_stats, so
there's no point in passing it when the mvm pointer is passed.
Remove the argument entirely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API tells the FW that it's allowed to use STBC
but the FW will decide on its own whether to use STBC
or SISO (and in the future Beamformer).
Keep support for the old API which sets STBC explicitly
in the rates in the LQ table while we still support old
FW revisions.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Prepare to add some more code there so refactor to
separate functions.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

for_each_set_bit expect the size in number of bits and not
in bytes.

Fixes: a0f6bf2a ("iwlwifi: mvm: use private TFD queues for TDLS stations")
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_mac_get_queues_mask() added vif->hw_queue[ac] to the
queue mask although it might be set to IEEE80211_INVAL_HW_QUEUE.
Fix it.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

With this value, we de-facto disable the feature. Since it
is not working yet, disable it completely.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

C step functionality in the driver is exactly the same as
B step besides the ucode name that present as iwlwifi-8000C-xx.ucode
instead of iwlwifi-8000B-xx.ucode
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a comment indicating that the WLAN_CIPHER_SUITE_WEP104 case falls
through to the WLAN_CIPHER_SUITE_WEP40 case in iwl_mvm_send_sta_key.
This will document that the lack of a break is intentional.

Coverity: CID 1260023
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Tx STBC was used only when in CAM mode or if powersave is disabled.
Effectively this meant we never used STBC as these modes aren't
used on most platforms by default. Change that.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is now implemented by mac80211 (commit below).
mac80211 will flush/drop the frames on the queues before
suspending / disconnecting.
It will then send the deauth and wait until the queues are
empty.

commit 3b24f4c6
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Wed Jan 7 15:42:39 2015 +0200

    mac80211: let flush() drop packets when possible

This reverts commit 4e6c48e0.

This new command will give finer granularity to configure
the platform.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allow to better preserve the BT performance while
WiFi is running.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to change the usage of U-APSD on the fly later,
move the enabling condition into a new function that is
called when authenticated.

This allows the module parameter to become writable, it
won't take effect immediately but at least on the next
association the new value will be used.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the firmware sends spontaneous DTS notfications with the
temperature (indicated in a TLV), we can ignore the temperature we get
in the RX statistics notifications.  This prevents potentially
handling the same temperature change twice.  It also ignores
notifications with temperature equal to 0 that happens from time to
time.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These aren't useful and overflowing so drop them
and also fix a minor typo.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to duplicate the structure field name in the string,
just generate the string in the macro that's there anyway. To keep
the debugfs output the same, rename one (otherwise unused) field.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware API structs are split differently, synchronize
the struct splits with the current firmware definitions.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the FW is in error status - try to read the RXF and
TXF (all of them) and add them to the dump data.

This shouldn't happen in non-error statuses, as we don't
want to stop the RXF/TXF while they are running.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some HW modules have two SRAMs. In such cases add the secondary SRAM to
the list of dumped segments.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As this functionality relies on getting a firmware notification
it is difficult to test. Allow accessing the data for it from
debugfs to be able to trigger all kinds of scenarios to test.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.

This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Print the nvm version in the log for debugging purposes.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
  fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is to work around interoperability bugs with devices
that don't hanle MIMO properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_fw_dbg_collect allows to collect debug data from
the firmware. Most of the firmware interaction is done in
non-sleepable context. It makes little sense to force the
caller of iwl_mvm_fw_dbg_collect to sleep.
Defer the actual collection to a worker so that this
function will be able to be called from any context.
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.

CC: <stable@vger.kernel.org> [3.10+]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we have an active scheduled scan, and the RFKILL
interrupt kicks in, the stack will cancel the scheduled
scan as part of the down flow. But cancelling scheduled
scan usually implies sending a command to the firwmare
which has been killed as part of the RFKILL interrupt
handling.
Because of that, we returned an error to mac80211 when
it asked to stop the scheduled scan and didn't notify the
end of the scheduled scan. Besides a fat warning, this led
to a situation in which cfg80211 would refuse any new scan
request.

To disentangle this, fake that the scheduled scan has been
stopped without sending the command to the firwmare, return
0 after having properly let cfg80211 know that the scan
has been cancelled.

This is basically the same as:
commit 9b520d84
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Tue Nov 4 15:54:11 2014 +0200

    iwlwifi: mvm: abort scan upon RFKILL

    This code existed but not for all the different FW APIs
    we support.
    Fix this.

but for the scheduled scan case.

Link: http://permalink.gmane.org/gmane.linux.kernel.wireless.general/133232Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

BAR tx cmd tid was set to non qos (8). This is wrong as BAR
should be sent with the tid of the BA session.
This led to a corruption in the firmware. The visible
effect of this from the driver side is the BA notification
that comes back after the BAR. It was botched and led to the
WARNING below.

------------[ cut here ]------------
WARNING: CPU: 2 PID: 17707 at /home/tester/workspace_hostap/iwlwifi/drivers/net/wireless/iwlwifi/mvm/tx.c:976 iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]()
Q 4500, tid 8, flow 65535
Modules linked in: iwlmvm(O) mac80211(O) iwlwifi(O) cfg80211(O) compat(O) netconsole configfs ctr ccm arc4 autofs4 microcode bnep rfcomm snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic snd_hda_intel joydev snd_hda_codec uvcvideo videobuf2_core snd_hwdep videodev snd_pcm videobuf2_vmalloc videobuf2_memops i915 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device drm_kms_helper dell_wmi dell_laptop drm btusb bluetooth snd psmouse i2c_algo_bit sparse_keymap wmi soundcore 6lowpan_iphc dcdbas serio_raw video lpc_ich ppdev mac_hid parport_pc nfsd nfs_acl auth_rpcgss nfs fscache binfmt_misc lockd sunrpc lp parport msdos sdhci_pci sdhci mmc_core ahci libahci e1000e ptp pps_core [last unloaded: compat]
CPU: 2 PID: 17707 Comm: irq/46-iwlwifi Tainted: G        W  O 3.14.17-patched #4
Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
 00000000 00000000 ebd49d6c c1616221 f985dbdc ebd49d9c c1044e44 f9861df4
 ebd49dc8 0000452b f985dbdc 000003d0 f98395da f98395da ebd49f10 eaf3d8a4
 0000ffff ebd49db4 c1044f03 00000009 ebd49dac f9861df4 ebd49dc8 ebd49e64
Call Trace:
 [<c1616221>] dump_stack+0x41/0x52
 [<c1044e44>] warn_slowpath_common+0x84/0xa0
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c1044f03>] warn_slowpath_fmt+0x33/0x40
 [<f98395da>] iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
 [<c10e9767>] ? trace_buffer_unlock_commit+0x37/0x50
 [<f98568a3>] ? iwl_tm_mvm_send_rx+0x53/0x90 [iwlmvm]
 [<f98327a8>] iwl_mvm_rx_dispatch+0x108/0x130 [iwlmvm]
 [<f9eac7e7>] iwl_pcie_irq_handler+0xf17/0x15b0 [iwlwifi]
 [<c10994c1>] irq_thread_fn+0x21/0x50
 [<c109926c>] irq_thread+0xec/0x110
 [<c10994a0>] ? irq_thread_dtor+0xb0/0xb0
 [<c10993f0>] ? irq_finalize_oneshot.part.34+0xc0/0xc0
 [<c1099180>] ? wake_threads_waitq+0x40/0x40
 [<c1062fdb>] kthread+0x9b/0xb0
 [<c1627137>] ret_from_kernel_thread+0x1b/0x28
 [<c1062f40>] ? flush_kthread_worker+0x90/0x90
---[ end trace 5e0f67374816db17 ]---
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>