Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 29 6月, 2012 6 次提交
    • C
      OMAPDSS: Add LCD3 overlay manager and Clock and IRQ support · e86d456a
      由 Chandrabhanu Mahapatra 提交于 
      The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.

The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
      e86d456a
    • C
      OMAPDSS: Add support for LCD3 channel · ff6331e2
      由 Chandrabhanu Mahapatra 提交于 
      OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
      ff6331e2
    • C
      OMAPDSS: Cleanup implementation of LCD channels · efa70b3b
      由 Chandrabhanu Mahapatra 提交于 
      The current implementation of LCD channels and managers consists of a number of
if-else construct which has been replaced by a simpler interface. A constant
structure mgr_desc has been created in Display Controller (DISPC) module. The
mgr_desc contains for each channel its name, irqs and  is initialized one time
with all registers and their corresponding fields to be written to enable
various features of Display Subsystem. This structure is later used by various
functions of DISPC which simplifies the further implementation of LCD channels
and its corresponding managers.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
      efa70b3b
    • T
      OMAPDSS: fix warnings if CONFIG_PM_RUNTIME=n · 5be3aebd
      由 Tomi Valkeinen 提交于 
      If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.

One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.

However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>
      5be3aebd
    • T
      OMAPDSS: Use PM notifiers for system suspend · 2b8501d7
      由 Tomi Valkeinen 提交于 
      The current way how omapdss handles system suspend and resume is that
omapdss device (a platform device, which is not part of the device
hierarchy of the DSS HW devices, like DISPC and DSI, or panels.) uses
the suspend and resume callbacks from platform_driver to handle system
suspend. It does this by disabling all enabled panels on suspend, and
resuming the previously disabled panels on resume.

This presents a few problems.

One is that as omapdss device is not related to the panel devices or the
DSS HW devices, there's no ordering in the suspend process. This means
that suspend could be first ran for DSS HW devices and panels, and only
then for omapdss device. Currently this is not a problem, as DSS HW
devices and panels do not handle suspend.

Another, more pressing problem, is that when suspending or resuming, the
runtime PM functions return -EACCES as runtime PM is disabled during
system suspend. This causes the driver to print warnings, and operations
to fail as they think that they failed to bring up the HW.

This patch changes the omapdss suspend handling to use PM notifiers,
which are called before suspend and after resume. This way we have a
normally functioning system when we are suspending and resuming the
panels.

This patch, I believe, creates a problem that somebody could enable or
disable a panel between PM_SUSPEND_PREPARE and the system suspend, and
similarly the other way around in resume. I choose to ignore the problem
for now, as it sounds rather unlikely, and if it happens, it's not
fatal.

In the long run the system suspend handling of omapdss and panels should
be thought out properly. The current approach feels rather hacky.
Perhaps the panel drivers should handle system suspend, or the users of
omapdss (omapfb, omapdrm) should handle system suspend.

Note that after this patch we could probably revert
0eaf9f52 (OMAPDSS: use sync versions of
pm_runtime_put). But as I said, this patch may be temporary, so let's
leave the sync version still in place.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NJassi Brar <jaswinder.singh@linaro.org>
Tested-by: NJassi Brar <jaswinder.singh@linaro.org>
      2b8501d7
    • R
      OMAPDSS: add clk_prepare_enable and clk_disable_unprepare · f11766d1
      由 Rajendra Nayak 提交于 
      In preparation of OMAP moving to Common Clk Framework(CCF) change
clk_enable() and clk_disable() calls to clk_prepare_enable() and
clk_disable_unprepare() in omapdss. This can be safely done, as omapdss
never enables or disables clocks in atomic context.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
[tomi.valkeinen@ti.com: updated patch description]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
      f11766d1
  3. 28 6月, 2012 2 次提交
  5. 09 6月, 2012 1 次提交
    • L
      Revert "drm/i915/crt: Do not rely upon the HPD presence pin" · 8f53369b
      由 Linus Torvalds 提交于 
      This reverts commit 9e612a00.

It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.

That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).

I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.

Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      8f53369b
  7. 08 6月, 2012 1 次提交
  9. 07 6月, 2012 5 次提交
  11. 06 6月, 2012 2 次提交
  13. 05 6月, 2012 14 次提交
  15. 04 6月, 2012 9 次提交