- 08 9月, 2016 2 次提交
-
-
由 Jaegeuk Kim 提交于
This patch enhances the xattr consistency of dirs from suddern power-cuts. Possible scenario would be: 1. dir->setxattr used by per-file encryption 2. file->setxattr goes into inline_xattr 3. file->fsync In that case, we should do checkpoint for #1. Otherwise we'd lose dir's key information for the file given #2. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Chao Yu 提交于
Like most filesystems, f2fs will issue discard command synchronously, so when user trigger fstrim through ioctl, multiple discard commands will be issued serially with sync mode, which makes poor performance. In this patch we try to support async discard, so that all discard commands can be issued and be waited for endio in batch to improve performance. Signed-off-by: NChao Yu <yuchao0@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 30 8月, 2016 1 次提交
-
-
由 Yunlei He 提交于
This patch enables to do fstrim without checkpoint, if there is no fs change. Signed-off-by: NYunlei He <heyunlei@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 21 7月, 2016 1 次提交
-
-
由 Christoph Hellwig 提交于
These two are confusing leftover of the old world order, combining values of the REQ_OP_ and REQ_ namespaces. For callers that don't special case we mostly just replace bi_rw with bio_data_dir or op_is_write, except for the few cases where a switch over the REQ_OP_ values makes more sense. Any check for READA is replaced with an explicit check for REQ_RAHEAD. Also remove the READA alias for REQ_RAHEAD. Signed-off-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Reviewed-by: NMike Christie <mchristi@redhat.com> Signed-off-by: NJens Axboe <axboe@fb.com>
-
- 16 7月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
This patch reverts 19a5f5e2 (f2fs: drop any block plugging), and adds blk_plug in write paths additionally. The main reason is that blk_start_plug can be used to wake up from low-power mode before submitting further bios. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 09 7月, 2016 2 次提交
-
-
由 Jaegeuk Kim 提交于
SetPageUptodate() issues memory barrier, resulting in performance degrdation. Let's avoid that. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This patch adds f2fs_set_page_dirty_nobuffer() copied from __set_page_dirty_buffer. When appending 4KB blocks in f2fs on pmem with multiple cores, this improves the overall performance. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 07 7月, 2016 2 次提交
-
-
由 Jaegeuk Kim 提交于
The readahead nat pages are more likely to be reclaimed quickly, so it'd better to gather more free nids in advance. And, let's keep some free nids as much as possible. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
Let's store orphan inode pages right away. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 14 6月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
This mount option is to enable original log-structured filesystem forcefully. So, there should be no random writes for main area. Especially, this supports host-managed SMR device. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 09 6月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
In f2fs, we don't need to keep block plugging for NODE and DATA writes, since we already merged bios as much as possible. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 08 6月, 2016 1 次提交
-
-
由 Mike Christie 提交于
Separate the op from the rq_flag_bits and have f2fs set/get the bio using bio_set_op_attrs/bio_op. Signed-off-by: NMike Christie <mchristi@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NHannes Reinecke <hare@suse.com> Signed-off-by: NJens Axboe <axboe@fb.com>
-
- 03 6月, 2016 4 次提交
-
-
由 Jaegeuk Kim 提交于
This patch registers all the inodes which have dirty metadata to sync when checkpoint is doing. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This patch introduces f2fs_i_links_write() to call mark_inode_dirty_sync() when changing inode->i_links. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This patch refactors to use inode pointer for set_inode_flag and clear_inode_flag. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This reverts commit b951a4ec. Conflicts: fs/f2fs/checkpoint.c
-
- 21 5月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
Given errors, this patch flushes pending bios as soon as possible. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 19 5月, 2016 2 次提交
-
-
由 Jaegeuk Kim 提交于
This patch uses percpu_count for sbi->alloc_valid_block_count. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This can reduce page counting overhead. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 17 5月, 2016 2 次提交
-
-
由 Jaegeuk Kim 提交于
It needs to maintain dirty file inodes only if DATA_FLUSH is set. Otherwise, let's avoid its overhead. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Yunlei He 提交于
No need inc dirty pages under inode lock Signed-off-by: NYunlei He <heyunlei@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 08 5月, 2016 4 次提交
-
-
由 Chao Yu 提交于
When testing f2fs with inline_dentry option, generic/342 reports: VFS: Busy inodes after unmount of dm-0. Self-destruct in 5 seconds. Have a nice day... After rmmod f2fs module, kenrel shows following dmesg: ============================================================================= BUG f2fs_inode_cache (Tainted: G O ): Objects remaining in f2fs_inode_cache on __kmem_cache_shutdown() ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Slab 0xf51ca0e0 objects=22 used=1 fp=0xd1e6fc60 flags=0x40004080 CPU: 3 PID: 7455 Comm: rmmod Tainted: G B O 4.6.0-rc4+ #16 Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 00000086 00000086 d062fe18 c13a83a0 f51ca0e0 d062fe38 d062fea4 c11c7276 c1981040 f51ca0e0 00000016 00000001 d1e6fc60 40004080 656a624f 20737463 616d6572 6e696e69 6e692067 66326620 6e695f73 5f65646f 68636163 6e6f2065 Call Trace: [<c13a83a0>] dump_stack+0x5f/0x8f [<c11c7276>] slab_err+0x76/0x80 [<c11cbfc0>] ? __kmem_cache_shutdown+0x100/0x2f0 [<c11cbfc0>] ? __kmem_cache_shutdown+0x100/0x2f0 [<c11cbfe5>] __kmem_cache_shutdown+0x125/0x2f0 [<c1198a38>] kmem_cache_destroy+0x158/0x1f0 [<c176b43d>] ? mutex_unlock+0xd/0x10 [<f8f15aa3>] exit_f2fs_fs+0x4b/0x5a8 [f2fs] [<c10f596c>] SyS_delete_module+0x16c/0x1d0 [<c1001b10>] ? do_fast_syscall_32+0x30/0x1c0 [<c13c59bf>] ? __this_cpu_preempt_check+0xf/0x20 [<c10afa7d>] ? trace_hardirqs_on_caller+0xdd/0x210 [<c10ad50b>] ? trace_hardirqs_off+0xb/0x10 [<c1001b81>] do_fast_syscall_32+0xa1/0x1c0 [<c176d888>] sysenter_past_esp+0x45/0x74 INFO: Object 0xd1e6d9e0 @offset=6624 kmem_cache_destroy f2fs_inode_cache: Slab cache still has objects CPU: 3 PID: 7455 Comm: rmmod Tainted: G B O 4.6.0-rc4+ #16 Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 00000286 00000286 d062fef4 c13a83a0 f174b000 d062ff14 d062ff28 c1198ac7 c197fe18 f3c5b980 d062ff20 000d04f2 d062ff0c d062ff0c d062ff14 d062ff14 f8f20dc0 fffffff5 d062e000 d062ff30 f8f15aa3 d062ff7c c10f596c 73663266 Call Trace: [<c13a83a0>] dump_stack+0x5f/0x8f [<c1198ac7>] kmem_cache_destroy+0x1e7/0x1f0 [<f8f15aa3>] exit_f2fs_fs+0x4b/0x5a8 [f2fs] [<c10f596c>] SyS_delete_module+0x16c/0x1d0 [<c1001b10>] ? do_fast_syscall_32+0x30/0x1c0 [<c13c59bf>] ? __this_cpu_preempt_check+0xf/0x20 [<c10afa7d>] ? trace_hardirqs_on_caller+0xdd/0x210 [<c10ad50b>] ? trace_hardirqs_off+0xb/0x10 [<c1001b81>] do_fast_syscall_32+0xa1/0x1c0 [<c176d888>] sysenter_past_esp+0x45/0x74 The reason is: in recovery flow, we use delayed iput mechanism for directory which has recovered dentry block. It means the reference of inode will be held until last dirty dentry page being writebacked. But when we mount f2fs with inline_dentry option, during recovery, dirent may only be recovered into dir inode page rather than dentry page, so there are no chance for us to release inode reference in ->writepage when writebacking last dentry page. We can call paired iget/iput explicityly for inline_dentry case, but for non-inline_dentry case, iput will call writeback_single_inode to write all data pages synchronously, but during recovery, ->writepages of f2fs skips writing all pages, result in losing dirent. This patch fixes this issue by obsoleting old mechanism, and introduce a new dir_list to hold all directory inodes which has recovered datas until finishing recovery. Signed-off-by: NChao Yu <yuchao0@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
When unmounting filesystem, we should release all the ino entries. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This patch injects ENOSPC failures. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
This patch converts grab_cache_page to f2fs_grab_cache_page. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 27 4月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
This patch splits the existing sync_node_pages into (f)sync_node_pages. The fsync_node_pages is used for f2fs_sync_file only. Acked-by: NChao Yu <yuchao0@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 15 4月, 2016 1 次提交
-
-
由 Jaegeuk Kim 提交于
This patch resolves the redundant condition check reported by David. Reported-by: NDavid Binderman <dcb314@hotmail.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 18 3月, 2016 1 次提交
-
-
由 Keith Mok 提交于
The crc function is done bit by bit. Optimize this by use cryptoapi crc32 function which is backed by h/w acceleration. Signed-off-by: NKeith Mok <ek9852@gmail.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 27 2月, 2016 1 次提交
-
-
由 Chao Yu 提交于
Add a new helper f2fs_flush_merged_bios to clean up redundant codes. Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 26 2月, 2016 1 次提交
-
-
由 Chao Yu 提交于
1. Inode mapping tree can index page in range of [0, ULONG_MAX], however, in some places, f2fs only search or iterate page in ragne of [0, LONG_MAX], result in miss hitting in page cache. 2. filemap_fdatawait_range accepts range parameters in unit of bytes, so the max range it covers should be [0, LLONG_MAX], if we use [0, LONG_MAX] as range for waiting on writeback, big number of pages will not be covered. This patch corrects above two issues. Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 24 2月, 2016 1 次提交
-
-
由 Yunlei He 提交于
The D state of wait_on_all_pages_writeback should be waken by function f2fs_write_end_io when all writeback pages have been succesfully written to device. It's possible that wake_up comes between get_pages and io_schedule. Maybe in this case it will lost wake_up and still in D state even if all pages have been write back to device, and finally, the whole system will be into the hungtask state. if (!get_pages(sbi, F2FS_WRITEBACK)) break; <--------- wake_up io_schedule(); Signed-off-by: NYunlei He <heyunlei@huawei.com> Signed-off-by: NBiao He <hebiao6@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
- 23 2月, 2016 9 次提交
-
-
由 Chao Yu 提交于
This patch enables to trace old block address of CoWed page for better debugging. f2fs_submit_page_mbio: dev = (1,0), ino = 1, page_index = 0x1d4f0, oldaddr = 0xfe8ab, newaddr = 0xfee90 rw = WRITE_SYNC, type = NODE f2fs_submit_page_mbio: dev = (1,0), ino = 1, page_index = 0x1d4f8, oldaddr = 0xfe8b0, newaddr = 0xfee91 rw = WRITE_SYNC, type = NODE f2fs_submit_page_mbio: dev = (1,0), ino = 1, page_index = 0x1d4fa, oldaddr = 0xfe8ae, newaddr = 0xfee92 rw = WRITE_SYNC, type = NODE f2fs_submit_page_mbio: dev = (1,0), ino = 134824, page_index = 0x96, oldaddr = 0xf049b, newaddr = 0x2bbe rw = WRITE, type = DATA f2fs_submit_page_mbio: dev = (1,0), ino = 134824, page_index = 0x97, oldaddr = 0xf049c, newaddr = 0x2bbf rw = WRITE, type = DATA f2fs_submit_page_mbio: dev = (1,0), ino = 134824, page_index = 0x98, oldaddr = 0xf049d, newaddr = 0x2bc0 rw = WRITE, type = DATA f2fs_submit_page_mbio: dev = (1,0), ino = 135260, page_index = 0x47, oldaddr = 0xffffffff, newaddr = 0xf2631 rw = WRITE, type = DATA f2fs_submit_page_mbio: dev = (1,0), ino = 135260, page_index = 0x48, oldaddr = 0xffffffff, newaddr = 0xf2632 rw = WRITE, type = DATA f2fs_submit_page_mbio: dev = (1,0), ino = 135260, page_index = 0x49, oldaddr = 0xffffffff, newaddr = 0xf2633 rw = WRITE, type = DATA Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Shawn Lin 提交于
>From the function name of get_valid_checkpoint, it seems to return the valid cp or NULL for caller to check. If no valid one is found, f2fs_fill_super will print the err log. But if get_valid_checkpoint get one valid(the return value indicate that it's valid, however actually it is invalid after sanity checking), then print another similar err log. That seems strange. Let's keep sanity checking inside the procedure of geting valid cp. Another improvement we gained from this move is that even the large volume is supported, we check the cp in advanced to skip the following procedure if failing the sanity checking. Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Chao Yu 提交于
In curseg cache, f2fs caches two different parts: - datas of current summay block, i.e. summary entries, footer info. - journal info, i.e. sparse nat/sit entries or io stat info. With this approach, 1) it may cause higher lock contention when we access or update both of the parts of cache since we use the same mutex lock curseg_mutex to protect the cache. 2) current summary block with last journal info will be writebacked into device as a normal summary block when flushing, however, we treat journal info as valid one only in current summary, so most normal summary blocks contain junk journal data, it wastes remaining space of summary block. So, in order to fix above issues, we split curseg cache into two parts: a) current summary block, protected by original mutex lock curseg_mutex b) journal cache, protected by newly introduced r/w semaphore journal_rwsem When loading curseg cache during ->mount, we store summary info and journal info into different caches; When doing checkpoint, we combine datas of two cache into current summary block for persisting. Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Chao Yu 提交于
Try to use block plug in more place as below to let process cache bios as much as possbile, in order to reduce lock overhead of queue in IO scheduler. 1) sync_meta_pages 2) ra_meta_pages 3) f2fs_balance_fs_bg Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Chao Yu 提交于
Introduce a new structure f2fs_journal to wrap journal info in struct f2fs_summary_block for readability. struct f2fs_journal { union { __le16 n_nats; __le16 n_sits; }; union { struct nat_journal nat_j; struct sit_journal sit_j; struct f2fs_extra_info info; }; } __packed; struct f2fs_summary_block { struct f2fs_summary entries[ENTRIES_IN_SUM]; struct f2fs_journal journal; struct summary_footer footer; } __packed; Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Yunlei He 提交于
fix missing skip pages info in f2fs_writepages trace event. Signed-off-by: NYunlei He <heyunlei@huawei.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Chao Yu 提交于
f2fs use single bio buffer per type data (META/NODE/DATA) for caching writes locating in continuous block address as many as possible, after submitting, these writes may be still cached in bio buffer, so we have to flush cached writes in bio buffer by calling f2fs_submit_merged_bio. Unfortunately, in the scenario of high concurrency, bio buffer could be flushed by someone else before we submit it as below reasons: a) there is no space in bio buffer. b) add a request of different type (SYNC, ASYNC). c) add a discontinuous block address. For this condition, f2fs_submit_merged_bio will be devastating, because it could break the following merging of writes in bio buffer, split one big bio into two smaller one. This patch introduces f2fs_submit_merged_bio_cond which can do a conditional submitting with bio buffer, before submitting it will judge whether: - page in DATA type bio buffer is matching with specified page; - page in DATA type bio buffer is belong to specified inode; - page in NODE type bio buffer is belong to specified inode; If there is no eligible page in bio buffer, we will skip submitting step, result in gaining more chance to merge consecutive block IOs in bio cache. Signed-off-by: NChao Yu <chao2.yu@samsung.com> Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Jaegeuk Kim 提交于
Likewise f2fs_write_cache_pages, let's do for node and meta pages too. Especially, for node blocks, we should do this before marking its fsync and dentry flags. Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-
由 Shuoran Liu 提交于
This patch introduces lifetime IO write statistics exposed to the sysfs interface. The write IO amount is obtained from block layer, accumulated in the file system and stored in the hot node summary of checkpoint. Signed-off-by: NShuoran Liu <liushuoran@huawei.com> Signed-off-by: NPengyang Hou <houpengyang@huawei.com> [Jaegeuk Kim: add sysfs documentation] Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>
-