Currently the enabling of LE on LE only devices causes an error. This
is a bit difference from other commands where trying to set the same
existing settings causes a positive response. Fix this behavior for
this single corner case.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: b6eea9ca ("mac802154: introduce driver-ops header")
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.

Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.

This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.

The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: NBrad Campbell <bradjc5@gmail.com>
Acked-by: NVarka Bhadram <varkabhadram@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Storing the `platform_data` struct inside of the SPI struct when using
the device tree allows for a later function to edit the content of that
struct. This patch refactors the `cc2520_get_platformat_data` function
to accept a pointer to a `cc2520_platform_data` struct and populates
the fields inside of it.

This change mirrors commit aaa1c4d2
("at86rf230: copy pdata to driver allocated space").
Signed-off-by: NBrad Campbell <bradjc5@gmail.com>
Acked-by: NVarka Bhadram <varkabhadram@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the allocation of the L2CAP channel for the BR/EDR security manager
fails, then the smp variable might be NULL. In that case do not try to
free the non-existing crypto contexts
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

OS X version 10.10.2 (and possibly older versions) doesn't support LE
Secure Connections but incorrectly copies all authentication request
bits from a Security Request to its Pairing Request. The result is that
an SC capable initiator (such as BlueZ) will think OS X intends to do SC
when in fact it's incapable of it:

< ACL Data TX: Handle 3585 flags 0x00 dlen 6
      SMP: Security Request (0x0b) len 1
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      SMP: Pairing Request (0x01) len 6
        IO capability: KeyboardDisplay (0x04)
        OOB data: Authentication data not present (0x00)
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
        Max encryption key size: 16
        Initiator key distribution: EncKey (0x01)
        Responder key distribution: EncKey IdKey Sign (0x07)
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
      SMP: Pairing Response (0x02) len 6
        IO capability: NoInputNoOutput (0x03)
        OOB data: Authentication data not present (0x00)
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
        Max encryption key size: 16
        Initiator key distribution: EncKey (0x01)
        Responder key distribution: EncKey Sign (0x05)

The pairing eventually fails when we get an unexpected Pairing Confirm
PDU instead of a Public Key PDU:

> ACL Data RX: Handle 3585 flags 0x02 dlen 21
      SMP: Pairing Confirm (0x03) len 16
        Confim value: bcc3bed31b8f313a78ec3cce32685faf

It is only at this point that we can speculate that the remote doesn't
really support SC. This patch creates a workaround for the just-works
model, however the MITM case is unsolvable because the OS X user has
already been requested to enter a PIN which we're now expected to
randomly generate and show the user (i.e. a chicken-and-egg problem).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The mgmt.c file should be reserved purely for HCI_CHANNEL_CONTROL. The
mgmt_control() function in it is already completely generic and has a
single user in hci_sock.c. This patch moves the function there and
renames it a bit more appropriately to hci_mgmt_cmd() (as it's a command
dispatcher).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In order to make the mgmt command handling more generic we can't have a
direct call to mgmt_init_hdev() from mgmt_control(). This patch adds a
new callback to struct hci_mgmt_chan. And sets it to point to the
mgmt_init_hdev() function for the HCI_CHANNEL_CONTROL instance.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are several mgmt protocol features that will be needed by more
than just the current HCI_CHANNEL_CONTROL. These include sending generic
events as well as handling pending commands. This patch moves these
functions out from mgmt.c to a new mgmt_util.c file.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To be able to have pending commands for different HCI channels we need
to be able to distinguish for which channel a command was sent to. The
channel information is already part of the socket data and can be
fetched using the recently added hci_sock_get_channel() function. To not
require all mgmt.c code to pass an extra channel parameter this patch
also adds a helper pending_find() & pending_find_data() functions which
act as a wrapper to the new mgmt_pending_find() & mgmt_pending_find_data()
APIs.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We'll need to have access to which HCI channel a socket is bound to, in
order to manage pending mgmt commands in clean way. This patch adds a
helper for the purpose.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

CSR controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Intel controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Atheros controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When doing scan through mgmt api, some controllers can do both le and
classic scan at same time. They can be distinguished by
HCI_QUIRK_SIMULTANEOUS_DISCOVERY set.

This patch enables them to use this feature when doing dual mode scan.
Instead of doing le, then classic scan, both scans are run at once.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch refactor BR/EDR inquiry and LE scan triggering logic into
separate methods.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some controllers allow both LE scan and BR/EDR inquiry to run at
the same time, while others allow only one, LE SCAN or BR/EDR
inquiry at given time.

Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core wether given controller can
do both LE scan and BR/EDR inquiry at same time.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch fix an issue when at86rf230_read_subreg was successful. The
function at86rf230_read_subreg will directly call regmap_read which
returns zero on successful. Nobody figured out issues yet because it was
only necessary to evaluate dvdd state while probing. This could make
trouble because the stack variable could have an random value.

The function is also used by reset the irq line before requesting irq, but
the value isn't evaluated afterwards.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When a different user requests a new set of local out-of-band data, then
inform all previous users that the data has been updated. To limit the
scope of users, the updates are limited to previous users. If a user has
never requested out-of-band data, it will also not see the update.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The length of the respone packet for Read Local OOB Extended Data
command has a calculation error. In case LE Secure Connections support
is not enabled, the actual response is shorter. Keep this in mind and
update the value accordingly.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In case LE Secure Connections is not enabled, then the command for
returning local out-of-band data should not include the confirmation
and random value for LE SC pairing. All other fields are still valid,
but these two need to be left out. In that case it is also no needed
to generate the public/private key pair for out-of-band pairing.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This seems to be a simple typo in the debugfs entry for the remote
out-of-band data entries.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The variable for the out-of-band random number was badly named and
with that confusing. Just rename it to local_rand so it is clear
what value it represents.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Just for pure debugging purposes print the remote out-of-band data
that has been received and is going to be used.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

It might be a bit counterintuitive to set a 'local' flag based on remote
data. This patch adds a clarifying comment to the pairing req/rsp
handlers when setting the LOCAL_OOB flag based on the PDU received from
the remote side.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When we receive the remote public key, if we have remote OOB data
there's no point in sending our public key to the remote if the OOB data
doesn't match. This patch moves the test for this higher up in the
smp_cmd_public_key() function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we haven't received remote OOB data we cannot perform any special
checks on the confirm value. This patch updates the check after having
received the public key to only perform the verification if we have
remote OOB data present.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If the SMP Pairing Request or Response PDU received from the remote
device indicates that it has received our OOB data we should set the
SMP_FLAG_LOCAL_OOB flag.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are several decisions in the SMP logic that depend not only on
whether we're doing SMP or not, but also whether local and/or remote OOB
data is present. This patch splits the existing SMP_FLAG_OOB into two
new flags to track local and remote OOB data respectively.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We need to store the local ra/rb value in order to verify the Check
value received from the remote. This patch adds a new 'lr' for the local
ra/rb value and makes sure it gets used when verifying the DHKey Check
PDU received from the remote.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The OOB public and secret key pair is different from the non-OOB pairing
procedure. SO when OOB method is in use, then use this key pair instead
of generating a new one.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Then the local out-of-band data for LE SC pairing is requested via Read
Local OOB Extended Data command, then fill in the values generated by
the smp_generate_oob function. Every call of this command will overwrite
previously generated values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds a smp_generate_oob function that allows to create
local out-of-band data that can be used for pairing and also provides
the confirmation and random value.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The security manager device will require the use of AES-CMAC hash for
out-of-band data generation. This patch makes sure it is correctly
set up and available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The LE Secure Connections Confirmation Value and LE Secure Connections
Random Value contants are required for the out-of-band data and so
just define them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Every Bluetooth Low Energy controller requires a local crypto context
to handle the resolvable private addresses. At the moment this is just
a single crypto context, but for out-of-band data generation it will
require an additional. To facility this, create a struct smp_dev that
will hold all the extra information. This patch is just the refactoring
in preparation for future changes.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Within the security manager, it makes sense to use kzfree instead of
kfree for all data structures. This ensures that no key material leaks
by accident.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>