If RXCSR_AUTOCLEAR flag is not cleard before PIO reading, one packet
may be recieved by musb fifo, but no chance to notify
software, so cause packet loss, follows the detailed process:

	- PIO read one packet
	- musb fifo auto clear the MUSB_RXCSR_RXPKTRDY
	- musb continue to recieve the next packet, and MUSB_RXCSR_RXPKTRDY
	is set
	- software clear the MUSB_RXCSR_RXPKTRDY, so there is no chance for
	musb to notify software that the 2nd recieved packet.

The patch does fix the g_ether issue below:

	- use fifo_mode 3 to enable double buffer
	- 'ping -s 1024 IP_OF_BEAGLE_XM'
	- one usb packet of 512 byte is lost, so ping failed,
	which can be observed by wireshark

note:
	Beagle xm takes musb rtl1.8 and may fallback to pio mode
	for unaligned buffer.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Buffer is mapped to dma when dma channel is
allocated. If, for some reason, dma channel
programming fails, musb code will fallback
to PIO mode to transfer that request. In
that case, we need to unmap the buffer
back to CPU.

MUSB RTL1.8 and above cannot handle buffers
which are not 32bit aligned. That happens to
every request sent by g_ether gadget
driver. Since the buffer sent was unaligned,
we need to fallback to PIO.

Because of that, g_ether was failing due
to missing buffer unmapping.

With this patch and [1] g_ether works fine
with all MUSB revisions.

Verified with OMAP3630 board, which has
MUSB RTL1.8 using g_ether and g_zero.

[1] http://www.spinics.net/lists/linux-usb/msg38400.htmlSigned-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb_gadget_queue() checks for '!req->buf' condition twice:
in the second case the code is both duplicated and unreachable
as the first check returns early.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 9f445cb2[USB: musb: disable
double buffering for older RTL versions] tries to disable double
buffer mode by writing endpoint hw max packet size to TXMAP/RXMAP.

First the approach can break full speed and cause overflow problems.
We should always set those registers with the actual max packet size
from endpoint descriptor.

Second, the problem describe by commit 9f445cb2
was caused by musb gadget driver; nothing to do with RTL revision as
originaly suspected.

The real fix to the problem is to always use actual max packet
size from endpoint descriptor to config TXMAP/RXMAP registers.

Cc: Cliff Cai <cliff.cai@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In function musb_gadget_setup() call put_device()
when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Acked-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

1, In Rx double buffer case, FIFO may have two packets, so
rxstate should be called to unload fifo if RXPKTRDY is set
even the current request has not been completed.

2, Commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85
introduces autoclear to support double buffer in dma mode 0,
so remove clearing RXPKTRDY manually for dma mode 0.

3, Commit c7af6b29ffeffbeb28caf39e5b2ce29b11807c7d may break
dma mode 1 for non-doublebuffer endpoint, fix it.

With this patch, either usbtest #5 or g_file_storage(writing
file to device in usb host) or g_ether have been tested OK in
double buffer case(using fifo mode 3). Also, this patch has
been verified that single buffer case can't be broken.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 broke
g_file_storage functionality by enabling AUTOCLEAR on
all cases without caring for all gadget drivers.

This patch will only enable AUTOCLEAR if our endpoint's
FIFO was configured with double buffering support. Note
this is not a complete fix, double buffered case still
doesn't work always, but that hasn't been working for
quite some time. Other than reverting the entire commit
and breaking testusb with double buffered case again,
I decided it was better to fix the single buffered case
and spend more time fixing double buffered case properly.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem reported by Sergei:

>how come? we need to send ZLP before giving back the request.
>Well, look at the code ionce again. We need to send ZLP *after*
>request->actual == request->length, but as the check is inserted
>after the ZLP send, ZLP *may* be sent once the first DMA completes,
>not the last.

The patch also has been discussed on the link below:

	http://marc.info/?t=128454814900001&r=1&w=2Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Reported-by: NSergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

musb_g_rx() always returns if next_request() call yields NULL, so the DBG()
near the function's end can never be invoked. Remove it along with unneeded
'return'; also remove the duplicate 'request' check...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch has been tested OK on beagle B5 board and
use usbtest #15 and #16 as testcase.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To accomplish this the function to register a gadget driver takes the bind
function as a second argument.  To make things clearer rename the function
to resemble platform_driver_probe.

This fixes many section mismatches like

	WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
	reference from the variable printer_driver to the function
	.init.text:printer_bind()
	The variable printer_driver references
	the function __init printer_bind()

All callers are fixed.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a partial revert of 7f26b3a7 ("drivers/usb: Remove unnecessary
return's from void functions") as this hunk will vanish in USB tree completely.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 46034dca (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DMA length should not go beyond the availabe space
of request buffer, so fix it.

Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Complete the current request only if the data transfer is over.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes one bugs of OUT transfer in double buffer case:

	-the current code only enable autoclear for dma mode 1, and not
	for dma mode 0

Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.

With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:

    #./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8   [1]

Also I have tested this patch can't make g_ether broken.

[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.

In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:

	-in double buffer case, fifo may accommodate more than one packet,
	even though it has contained one packet already and is non-empty

	-since last DMA is completed before calling musb_g_tx, it is sure
	that fifo may accommodate at least one packet

Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.

With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:

	#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8   [1]

[1],
    -source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For shared fifo hw endpoint(with FIFO_TXRX style), only ep_in
field of musb_hw_ep is intialized in musb_g_init_endpoints, and
ep_out is not initialized, but musb_g_rx and rxstate may access
ep_out field of musb_hw_ep by the method below:

	musb_ep = &musb->endpoints[epnum].ep_out

which can cause the kernel panic[1] below, this patch fixes the issue
by getting 'musb_ep' from '&musb->endpoints[epnum].ep_in' for shared fifo
endpoint.

[1], kernel panic
[root@OMAP3EVM /]# musb_interrupt 1583: ** IRQ peripheral usb0008 tx0000 rx4000
musb_stage0_irq 460: <== Power=f0, DevCtl=99, int_usb=0x8
musb_g_rx 772: <== (null), rxcsr 4007 ffffffe8
musb_g_rx 786:  iso overrun on ffffffe8
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT
last sysfs file: /sys/devices/platform/musb_hdrc/usb1/usb_device/usbdev1.1/dev
Modules linked in: g_zero
CPU: 0    Tainted: G        W    (2.6.35-rc6-gkh-wl+ #92)
PC is at musb_g_rx+0xfc/0x2ec
LR is at vprintk+0x3f4/0x458
pc : [<c02c07a4>]    lr : [<c006ccb0>]    psr: 20000193
sp : c760bd78  ip : c03c9d70  fp : c760bdbc
r10: 00000000  r9 : fa0ab1e0  r8 : 0000000e
r7 : c7e80158  r6 : ffffffe8  r5 : 00000001  r4 : 00004003
r3 : 00010003  r2 : c760bcd8  r1 : c03cd030  r0 : 0000002e
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 8778c019  DAC: 00000017
Process kmemleak (pid: 421, stack limit = 0xc760a2e8)
Stack: (0xc760bd78 to 0xc760c000)
bd60:                                                       ffffffe8 c04b1b58
bd80: ffffffe8 c7c01ac0 00000000 c7e80d24 c0084238 00000001 00000001 c7e80158
bda0: 0000000e 00000008 00000099 000000f0 c760be04 c760bdc0 c02bcd68 c02c06b4
bdc0: 00000099 00000008 00004000 c760bdd8 c03cc4f8 00000000 00000002 c7e80158
bde0: c7d2e300 60000193 c760a000 0000005c 00000000 00000000 c760be24 c760be08
be00: c02bcecc c02bc1ac c7d2e300 c7d2e300 0000005c c760a000 c760be54 c760be28
be20: c00ad698 c02bce6c 00000000 c7d2e300 c067c258 0000005c c067c294 00000001
be40: c760a000 00000000 c760be74 c760be58 c00af984 c00ad5fc 0000005c 00000000
be60: 00000000 00000002 c760be8c c760be78 c0039080 c00af8d0 ffffffff fa200000
be80: c760beec c760be90 c0039b6c c003900c 00000001 00000000 c7d1e240 00000000
bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec
bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff 00000000 c068bae8
bee0: c760bf24 c760bef0 c00ff7d0 c0064ec4 00000001 00000000 c00ff700 00000000
bf00: c0087f00 00000000 60000013 c0d76a70 c0e23795 00000001 c760bf4c c760bf28
bf20: c00ffdd8 c00ff70c c068bb08 c068bae8 60000013 c0100938 c068bb30 00000000
bf40: c760bf84 c760bf50 c010014c c00ffd84 00000001 00000000 c010000c 00012c00
bf60: c7c33f04 00012c00 c7c33f04 00000000 c0100938 00000000 c760bf9c c760bf88
bf80: c01009a8 c0100018 c760bfa8 c7c33f04 c760bff4 c760bfa0 c0088000 c0100944
bfa0: c760bf98 00000000 00000000 00000001 dead4ead ffffffff ffffffff c08ba2bc
bfc0: 00000000 c049e7fa 00000000 c0087f70 c760bfd0 c760bfd0 c7c33f04 c0087f70
bfe0: c006f5e8 00000013 00000000 c760bff8 c006f5e8 c0087f7c 7f0004ff df2000ff
Backtrace:
[<c02c06a8>] (musb_g_rx+0x0/0x2ec) from [<c02bcd68>] (musb_interrupt+0xbc8/0xcc0)
[<c02bc1a0>] (musb_interrupt+0x0/0xcc0) from [<c02bcecc>] (generic_interrupt+0x6c/0x84)
[<c02bce60>] (generic_interrupt+0x0/0x84) from [<c00ad698>] (handle_IRQ_event+0xa8/0x1ec)
 r7:c760a000 r6:0000005c r5:c7d2e300 r4:c7d2e300
[<c00ad5f0>] (handle_IRQ_event+0x0/0x1ec) from [<c00af984>] (handle_level_irq+0xc0/0x13c)
[<c00af8c4>] (handle_level_irq+0x0/0x13c) from [<c0039080>] (asm_do_IRQ+0x80/0xa0)
 r7:00000002 r6:00000000 r5:00000000 r4:0000005c
[<c0039000>] (asm_do_IRQ+0x0/0xa0) from [<c0039b6c>] (__irq_svc+0x4c/0xb4)
Exception stack(0xc760be90 to 0xc760bed8)
be80:                                     00000001 00000000 c7d1e240 00000000
bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec
bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff
 r5:fa200000 r4:ffffffff
[<c0064eb8>] (sub_preempt_count+0x0/0x100) from [<c00ff7d0>] (find_and_get_object+0xd0/0x110)
 r5:c068bae8 r4:00000000
[<c00ff700>] (find_and_get_object+0x0/0x110) from [<c00ffdd8>] (scan_block+0x60/0x104)
 r8:00000001 r7:c0e23795 r6:c0d76a70 r5:60000013 r4:00000000
[<c00ffd78>] (scan_block+0x0/0x104) from [<c010014c>] (kmemleak_scan+0x140/0x484)
[<c010000c>] (kmemleak_scan+0x0/0x484) from [<c01009a8>] (kmemleak_scan_thread+0x70/0xcc)
 r8:00000000 r7:c0100938 r6:00000000 r5:c7c33f04 r4:00012c00
[<c0100938>] (kmemleak_scan_thread+0x0/0xcc) from [<c0088000>] (kthread+0x90/0x98)
 r5:c7c33f04 r4:c760bfa8
[<c0087f70>] (kthread+0x0/0x98) from [<c006f5e8>] (do_exit+0x0/0x684)
 r7:00000013 r6:c006f5e8 r5:c0087f70 r4:c7c33f04
Code: e3002312 e58d6000 e2833e16 eb0422d5 (e5963020)
---[ end trace f3d5e96f75c297b7 ]---
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1

There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.

Standardize them a bit.

Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

The removed part always evaluates to false.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Trying to use double buffer modes in RTL versions <2.0 may result in
infinite hangs or data corruption.  So avoid them with older versions.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the following NULL pointer dereference issue.

Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.

============
Code Snippet
============

748:  request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
	csr &= ~(MUSB_RXCSR_AUTOCLEAR
			| MUSB_RXCSR_DMAENAB
			| MUSB_RXCSR_DMAMODE);
	musb_writew(epio, MUSB_RXCSR,
		MUSB_RXCSR_P_WZC_BITS | csr);

792:	 request->actual += musb_ep->dma->actual_len;
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.

Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: NArnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
                                             pointer types lacks a cast

So switch to min_t(size_t, ...).
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 7723de7e (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following sparse warnings:

drivers/usb/musb/musb_gadget.c:1161:5: warning: symbol 'musb_gadget_set_halt' was not declared. Should it be static?

drivers/usb/musb/musb_gadget.c:1244:5: warning: symbol 'musb_gadget_set_wedge' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the pointless 'do () while (0)' loop from musb_g_tx() -- it
makes this function symmetric to musb_g_rx()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement the driver's set_wedge() method by adding the 'wedged' flag
to the 'struct musb_ep'.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.

Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate().  And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...

While at it, also do the following changes :

- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
  driver does not allow stalling with non-empty Tx FIFO anyway);

- in rxstate(), stop pointlessly zeroing the 'csr' variable;

- in musb_gadget_set_halt(), move the 'done' label to a more proper
  place;

- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently, with Inventra DMA, we use Mode 0 if transfer size is less
than or equal to the endpoint's maxpacket size.  This requires that
we explicitly set TXPKTRDY for that transfer.

However the musb_g_tx code will not set TXPKTRDY twice if the last
transfer is exactly equal to maxpacket, even if request->zero is set.
Using Mode 1 will solve this; a better fix might be in musb_g_tx().

Without this change, musb will not correctly send out a ZLP if the
last transfer is the maxpacket size and request->zero is set.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adjust HNP state machines in MUSB driver so that they handle the
case where the cable is disconnected.  The A-side machine was
very wrong (unrecoverable); the B-Side was much less so.

 - A_PERIPHERAL ... as usual, the non-observability of the ID
   pin through Mentor's registers makes trouble.  We can't go
   directly to A_WAIT_VFALL to end the session and start the
   disconnect processing.  We can however sense link suspending,
   go to A_WAIT_BCON, and from there use OTG timeouts to finally
   trigger that A_WAIT_VFALL transition.  (Hoping that nobody
   reconnects quickly to that port and notices the wrong state.)

 - B_HOST ... actually clear the Host Request (HR) bit as the
   messages say, disconnect the peripheral from the root hub,
   and don't detour through a suspend state.  (In some cases
   this would eventually have cleaned up.)

Also adjust the A_SUSPEND transition to respect the A_AIDL_BDIS
timeout, so if HNP doesn't trigger quickly enough the A_WAIT_VFALL
transition happens as it should.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor HNP bugfixes, so the initial role switch works:

 - A-Device:
     * disconnect-during-suspend enters A_PERIPHERAL state
     * kill OTG timer after reset as A_PERIPHERAL ...
     * ... and also pass that reset to the gadget
     * once HNP succeeds, clear the "ignore_disconnect" flag
     * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON

 - B-Device:
     * kill OTG timer on entry to B_HOST state (HNP succeeded)
     * once HNP succeeds, clear "ignore_disconnect" flag
     * kick the root hub only _after_ the state is adjusted

Other state transitions are left alone.  Notably, exit paths from
the "roles have switched" state ... A_PERIPHERAL handling of that
stays seriously broken.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated.  OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Suppress "parasitic" endpoint interrupts in the DMA mode
when using CPPI DMA driver; they're caused by the MUSB gadget
driver using the DMA request mode 0 instead of the mode 1.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MUSB code clears TXCSR_DMAMODE incorrectly in several
places, either asserting that TXCSR_DMAENAB is clear (when
sometimes it isn't) or clearing both bits together.  Recent
versions of the programmer's guide require DMAENAB to be
cleared first, although some older ones didn't.

Fix this and while at it:

 - In musb_gadget::txstate(), stop clearing the AUTOSET
   and DMAMODE bits for the CPPI case since they never
   get set anyway (the former bit is reserved on DaVinci);
   but do clear the DMAENAB bit on the DMA error path.

 - In musb_host::musb_ep_program(), remove the duplicate
   DMA controller specific code code clearing the TXCSR
   previous state, add the code to clear TXCSR DMA bits
   on the Inventra DMA error path, to replace such code
   (executed late) on the PIO path.

 - In musbhsdma::dma_channel_abort()/dma_controller_irq(),
   add/use the 'offset' variable to avoid MUSB_EP_OFFSET()
   invocations on every RXCSR/TXCSR access.

[dbrownell@users.sourceforge.net: don't introduce CamelCase,
shrink diff]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.

[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>