Update 10.4 WMI service map to sync to the latest 10.4 firmware
as of 1/20/2016.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh.
Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S.
Also add _11S as post-fix to each of WMI_SERVICE_MESH and
WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh.
This will help users to distinguish 11s Mesh from non 11s Mesh.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Tx vring needs to be enlarged to get better
performance for traffic over 2Gbps.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case there are multiple WMI commands with the same reply_id,
the following scenario can occur:
- Driver sends the first command to the device
- The reply didn’t get on time and there is timeout
- Reply_id, reply_buf and reply_size are set to 0
- Driver sends second wmi command with the same reply_id as the first
- Driver sets wil->reply_id
- Reply for the first wmi command arrives and handled by wmi_recv_cmd
- As its ID fits the reply_id but the reply_buf is not set yet it is
handled as a reply with event handler, and WARN_ON is printed

This patch guarantee atomic setting of all the reply variables and
prevents the above scenario.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wil_tx_vring locks the vring_tx_data lock before accessing the TX
vring to check if it is enabled and valid for use.
In case of quick disconnect / connect events for the same station,
spin_lock(&txdata->lock) can be called during the lock initialization
in the vring init function.
To prevent such a race, the TX vrings spin lock should be initialized
once during wil6210 driver initialization.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

I think this limit was added when CSA with multiple interfaces wasn't
working yet. It should no longer be necessary
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Like how pci.c exposes hif ops for the bus specific operation,
expose similar hif ops table for ahb with all required functions
linked to it. Many ath10k_pci_* functions are reused here in hif ops
table. If something is not sharable, new functions are added for ahb
and linked to hif ops table.

Finally, make ath10k_ahb_probe/remove() to perform what is expected
out of it.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add function to gather resources required for qca4019 to operate
(memory, irq, dma setting, clock init , rest control init) and
function release those resources when it's not needed.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add irq related functions to register,handle,release,disable interrupt.

qca4019 supports msi interrupt, but it has the problem. Until the issue
gets sorted out, only legacy interrupt model is enabled and used.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add function to perform chip halt sequence and function to halt axi
bus in ahb module. Mainly used in the scenario like driver unload.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To perform reset on qca4019 wifi, multiple reset lines needs
to be toggled in a sequence with help of reset controller support
in the kernel. This patch adds functions to reset control init/deinit
and release reset.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

pre qca4019 chipsets has/uses internal clock generator for
the operation. But, qca4019 uses external clocks supplied from
outside of target (ie, outside of wifi core). Three different clocks
(cmd clock, ref clock, rtc clock) comes into picture in qca4019.
All those clocks needs to configured with help of global clock
controller (gcc) to make qca4019 functioning.

Add functions for clock init/deinit, clock enable/disable in ahb.
This is just a preparation, functions added in this patch will be
used in later patches.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca4019 deals with below register memory region to control the clock,
reset, etc.

        - Memory to control wifi core
        - gcc (outside of wifi)
        - tcsr (outside of wifi)

Add new helper functions to perform read/write in above registers
spaces. Actual ioremap for above registers are done in later patch.
Struct ath10k_ahb is introduced to maintain ahb specific info and
memory this struct will be allocated in the continuation of struct
ath10k_pci (again, memory ath10k_ahb is allocated in the later patch).
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New register table is added for qca4019 to tell about it's
register mapping details.

Nothing much other than this.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca4019 uses ahb instead of pci where it slightly differs in device
enumeration, clock control, reset control, etc. Good thing is that
ahb also uses copy engine for the data transaction. So, the most of
the stuff implemented in pci.c/ce.c are reusable in ahb case too.

Device enumeration in ahb case comes through platform driver/device
model. All resource details like irq, memory map, clocks, etc for
qca4019 can be fetched from of_node of platform device.

Simply flow would look like,

 device tree => platform device (kernel) => platform driver (ath10k)

Device tree entry will have all qca4019 resource details and the same
info will be passed to kernel. Kernel will prepare new platform device
for that entry and expose DT info to of_node in platform device.
Later, ath10k would register platform driver with unique compatible name
and then kernels binds to corresponding compatible entry & calls ath10k
ahb probe functions. From there onwards, ath10k will take control of it
and move forward.

New bool flag CONFIG_ATH10K_AHB is added in Kconfig to conditionally
enable ahb support in ath10k. On enabling this flag, ath10k_pci.ko
will have ahb support. This patch adds only basic skeleton and few
macros to support ahb in the context of qca4019.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some of the code present in ath10k_pci_{probe|remove} are reusable
in ahb case too. To avoid code duplication, move reusable code to
new functions. Later, those new functions can be called from ahb
module's probe and exit functions.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_pci_read32/write32() does work more specific to
PCI by ensuring pci wake/sleep for every read and write.
There is a plan to use most of stuff available in pci.c
(irq stuff, copy engine, etc) for AHB case. Such kind
of pci wake/sleep for every read/write is not required
in AHB case (qca4019). All those reusable areas in pci.c
and ce.c calls ath10k_pci_read32/write32() for low level
read and write.

In fact, ath10k_pci_read32/write32() should do what it does
today for PCI case. But for AHB, it has to do differently.
To make ath10k_pci_read32/write32() more generic, new function
pointers are added in ar_pci for the function which does
operation more close to the bus. Later, corresponding bus
specific read and write function will be mapped to that.

ath10k_pci_read32/write32() are changed to call directly
those function pointers without worrying which bus underlying
to it. Also, the function to get number of bank is changed
in the same way.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some of static functions present in pci.c file are reusable
in ahb (qca4019) case. Remove static word for those reusable
functions and have those function prototype declaration in
pci.h file. So that, pci.h header file can be included in
ahb module and reused. There is no functionality changes done
in this patch.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes the code easier to extend and re-use.

While at it fix _warn to _err. Other than that
there are no functional changes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.

Primary function of this is improved MU-MIMO
performance with multiple clients.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New names make a bit more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

One crash issue be found on ar9300: RTC_RC reg read leads crash, leading
the data bus error, due to RTC_RC reg write not happen properly.

Warm Reset trigger in continuous beacon stuck for one of the customer for
other chip, noticed the MAC was stuck in RTC reset. After analysis noticed
DMA did not complete when RTC was put in reset.

So, before resetting the MAC need to make sure there are no pending DMA
transactions because this reset does not reset all parts of the chip.

The 12th and 11th bit of MAC _DMA_CFG register used to do that.
	12 cfg_halt_ack 0x0
		0 DMA has not yet halted
		1 DMA has halted
	11 cfg_halt_req 0x0
		0 DMA logic operates normally
		1 Request DMA logic to stop so software can reset the MAC

The Bit [12] of this register indicates when the halt has taken effect or
not. the DMA halt IS NOT recoverable; once software sets bit [11] to
request a DMA halt, software must wait for bit [12] to be set and reset
the MAC.

So, the same thing we implemented for ar9580 chip.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Minor changes for indenting.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

BB panic(0x4000409) observed while AP enabling/disabling
bursting.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit c24bd362 ("ath9k: Do not maintain ANI state per-channel")
removed per-channel handling, the code to check 'curchan' also
should be removed as never used.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes commit 54da20d8 ("ath9k_hw: improve ANI processing and rx desensitizing parameters")

Call ath9k_ani_restart() only when the phy error rate reach the
ANI immunity threshold. Sync the logic with internal code base.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath9k/channel.c:230: warning: type qualifiers ignored on function return type
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Used in some newer TP-Link AR9533 devices.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.

In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In TX vring allocation, vring_tx->va is allocated before WMI command to
configure the vring is sent to the device. As the WMI command can take
time to complete, it can lead to scenarios where vring_tx->va is not NULL
but vring is still not enabled.

This patch adds a check that vring_tx_data is enabled before returning
a valid TX vring.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wil_vring_fini_tx is called in disconnect in order to free the
allocated vrings.
wil_vring_fini_tx is disabling the vring_tx_data before napi_synchronize
is called in order to avoid the tx handling of this vring, while
wil_vring_free is called only after napi finished the current handling
of the tx completed packets.
Due to that, in case of disconnect, wil6210_netdev_poll_tx can be called
when vring->va is not NULL but vring_tx_data[i]->enabled is already
disabled.

This patch checks vring_tx_data[i]->enabled in wil6210_netdev_poll_tx
to prevent handling of disabled vrings.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the start_ap/change_beacon API, when we set up probe response
offloading, we only use the IE list from the probe response
template and not the IE list from the proberesp_ies argument.
As a result, we miss important IEs and it causes problems with
some scenarios such as P2P.
With this change, we merge the list of IEs from the probe response
template and proberesp_ies and send the merged list to the FW
for offloading. It is still FW responsibility to filter out
irrelevant IEs when sending probe response, based on the actual
contents of the probe request.
Also in case association response termplate is not provided,
we will use the merged list of IEs from probe response in the
association response as well.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently the privacy flag calculation in change_beacon
checks for RSN IE inside proberesp_ies, but normally it
is not found there. It works today because of code inside
the function wil_fix_bcon, but wil_fix_bcon is not directly
related to change_beacon, and it may be changed or removed
in the future and break the calculation.
To fix this issue, change the privacy flag calculation
to check RSN IE inside the beacon itself. The new check is more
reliable and will not be sensitive to changes in wil_fix_bcon.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This device is available under different marketing names:
WLM-20U2 - Wireless USB Dongle for Toshiba TVs
GN-1080 - Wireless LAN Module for Toshiba MFPs.
Signed-off-by: NAlexander Tsoy <alexander@tsoy.me>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Request NOA update when chanctx active, also in case
of STA.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The p2p NOA never been supported at 10.2.4 FW, remove it to avoid SWBA
event parse error for multi beacon interval case.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>