Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi
part is a BCM43362 IC connected to MMC3 in the A20 SoC via SDIO.
The IC also takes a power enable signal via GPIO.

The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not supported in this patch.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A20 SoCs to
arch/arm/boot/dts/sun7i-a20.dtsi.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a new sun6i-a31-m9 dts file for the Mele M9 / Mele A1000G Quad. These
HTPCs use the same board in a different case, for more details see:
http://linux-sunxi.org/Mele_M9Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A31 SoCs to
arch/arm/boot/dts/sun6i-a31.dtsi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add clk-nodes for the mmc clocks.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 3 mmc controllers found on A10s SoCs and for the 2 mmc
controllers found on A13 SoCs.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mmc0 is the only controller actually being used on boards, so limit the
pin-muxing options to that.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A10 SoCs to
arch/arm/boot/dts/sun4i-a10.dtsi.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the PWM for both PWM channels on the cubietruck. They can be found on
connector CN8.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A20.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A10.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A20.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A10.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the performance monitoring unit found in the A31 SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

Enable the performance monitoring unit found in the A20 SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

Now that we have a DMA driver, we can add the DMA bindings in the DTSI for the
controller and the devices supported that can use DMA.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The DT are supposed to be ordered by physical address. Move the NMI node where
it belongs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The prcm lives at address 0x01f01400 as the reg entry in its node already
correctly indicates, rename the node to match this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)
Signed-off-by: NSteven Miao <realmz6@gmail.com>

Signed-off-by: NSteven Miao <realmz6@gmail.com>

In v3.2 the Analog Devices ADT75 temperature sensor driver was removed
as an IIO driver and support for it was added to the LM75 HWMON driver.
But it was apparently overlooked to rename one reference to CONFIG_ADT75
to CONFIG_SENSORS_LM75. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices AD7314 temperature sensor driver was removed
as an IIO driver and added as a HWMON driver. But it was apparently
overlooked to rename two references to CONFIG_AD7314 to
CONFIG_SENSORS_AD7314. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices ad2s1200/ad2s1205 driver was renamed from
ad2s120x to ad2s1200. But it apparently forgot to rename the references
to this driver in the BF537-STAMP code. Rename these now, and use the
IS_ENABLED() macro, while we're at it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>

There's a (rather subtle) typo in "CONFIG_SND_SOC_ADV80X_MODULE". Fix it
once and for all by using IS_ENABLED(), which is designed to avoid
issues like this.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NSteven Miao <realmz6@gmail.com>