If the creation fails, this keeps us from crashing later when
trying to do a list_del(arvif->list).
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_pci_wait() didn't notify any errors to callers, it
just printed a warning so add proper error handling. This fixes
a crash Ben reported:

ath10k: MSI-X interrupt handling (8 intrs)
ath10k: Unable to wakeup target
ath10k: target took longer 5000 us to wake up (awake count 1)
ath10k: Failed to get pcie state addr: -16
ath10k: early firmware event indicated
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci]
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.1.389 firmware has some differences in
calculation of number of outstanding HTT TX
completions. This led to FW crashes of 10.1.389
while main firmware branch was unnaffected.

The patch makes sure ath10k doesn't queue up more
MSDUs than it should.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to access SOC registers. No functional
changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware crashes during FW probing it would try
to perform FW recovery which uses mac80211
workqueue before registering to mac80211.

Using internal workqueue solves the problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

NSTS values reported in the VHT-SIG-A1 are 0
through 7 but they actually describe number of
streams 1 through 8.

1SS frames were dropped. This patch fixes this.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes incorrect values being printed on
big-endian hosts.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add a few checks and warnings to make it easier to
track any kind of monitor vdev mismanagement.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes issue with interface bridging.

Linux bridging sets promiscuous mode for all
interfaces that are in a bridge. This translates
to configure_filter() being called in a mac80211
driver.

Before the patch operational interface would be
started and upped again when promiscuous mode was
enabled causing all sorts of strange issues:

 * no HTT RX happening (i.e. no traffic)
 * FW crash upon driver reload/unload
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCI and SoC specific drivers are using separate
code now so it is not reasonable to use the same
module for both drivers anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_hwcrypt_disabled' function is the
only PCI specific callback which is used by the
SoC driver. Create a clone of that to get rid of
the dependency.

Even though the two functions are using the same
variable, but the SoC specific code will be moved
into a separate module which will have its own
'modparam_nohwcrypt' variable.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the function into the rt2800mmio module, in order
to make it usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function is called for PCI and SoC devices
however the MCU related part of the function
has no effect on SoC devices. Move the common
part of the function into a separate helper and
use that for the SoC devices.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function contain code for SoC devices only.
Rename the function to 'rt2800soc_disable_radio'
and move it to the SoC specific section. Use
the renamed function in the SoC specific code
only and remove the 'if rt2x00_is_soc(rt2x00dev)'
condition from the function body.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_set_state' function uses MCU commands
to set the device state, however these have no effect
on SoC devices. Use a different set_state callback
which does not use the MCU fcuntions.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use empty firmware callbacks for SoC devices because those
don't require firmware.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the 'rt2800pci_read_eeprom_soc function' to
'rt2800soc_read_eeprom' and use that directly in the
SoC specific 'rt2800_ops' structure. Also move the
'rt2800pci_eeprom_read' function into an 'ifdef PCI'
section and remove the 'rt2800pci_read_eeprom_soc'
call from that.

Additionally, remove the dummy inline eeprom functions.
Those are not used anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it possible to use different callback
functions for PCI and SoC devices which will allow
to move the SoC driver into a separate module.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules. Also move
the queue register offset macros from rt2800pci.h
into rt2800mmio.h.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules. Also move
the RX descriptor related defines from rt2800pci.h
into rt2800mmio.h
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules. Also move
the TX descriptor related defines from rt2800pci.h
into rt2800mmio.h.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create a new module for common code which can be used
for rt2800 device with memory mapped I/O. It is an empty
module for now, but it will be populated by subsequent
patches.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a typo where the checking for priv->ReAssociationRequestRetryCnt must
be, it was checking for priv->AssociationRequestRetryCnt instead.
Signed-off-by: NFelipe Pena <felipensp@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the SDIO host controller does not support scatter-gather the glom
superframe must be transfered from the device and the data for each
packet in the queue must be extracted from it.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When running on a host controller that does not support scatter-gather
transfers the function brcmf_sdio_txpkt_prep() should not add tail
padding buffers.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the host does not support scatter-gather transmit the packets
in the pktq individually using brcmf_sdio_buffrw().
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_sdcard_recv_chain() has been reworked with
commit "brcmfmac: add sdio sg list support", but the incr_fix
variable is only assigned but not used so removing it now.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all calls to the function brcmf_sdio_addrprep() check
the return value, but it may fail so better verify it.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_sdio_sglist_rw() does a different code path
when packet queue length is 1. Move this to a separate function
reducing overhead in the calling context.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_sdio_buffrw() is intended to be used for
transfering list of packets using scatter-gather functionality.
Rename function to brcmf_sdio_sglist_rw() to clarify this.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moving a number of assignments outside of the loop as they are
the same for each request.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of determining the limits for scatter-gather MMC transfer
request upon each transmit it is now determined during the probe
of the SDIO function.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>