CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.

Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.

The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also the R4000 / R4600 LL/SC instructions imply a sync so no explicit sync
needed.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For the definition of atomic64_t atomic.h was relying on <asm/types.h>
having been included previously.  Before changeset
d89d8e0637a5e4e0a12e90c4bc934d0d4c335239 this was happening as a
side effect of including <linux/spinlock.h>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

N32 SysV IPC system calls should use 32-bit compatible code.
arch/mips/kernel/linux32.c have similar compatible code for O32, but
ipc/compat.c seems more complete.  We can use it for both N32 and O32.

This patch should fix these problems (and other possible problems):

http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=1149188824.6986.6.camel%40diimka-laptop
http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=44C6B829.8050508%40caviumnetworks.comSigned-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

OK, that seems to be enough to deal with the mess.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This was exposed by Al's recent header file dependency reduction
patches..

Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds missing bracket.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make the m68knommu DMA handling consistent with other architectures.
Compile problems pointed out by Adrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.

(This part of the patch if the memory register defines for the 520x
ColdFire CPU family - Greg).
Signed-off-by: NMichael Broughton <mbobowik@telusplanet.net>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL.
The page mask which is used to make sure memory_end is on 4MB/2MB
boundary is wrong and not needed. Therefore remove it.
Make sure a vmalloc area does also exist and work on (future)
machines with 4TB and more memory.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Using memcmp to compare ccw_dev_id implies that the whole structure (incl.
padding) has always been completely initialized to sane values. Comparing
the structures field by field doesn't make such assumptions.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Need this at yet another file and don't want to add yet another
extern...
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In case of reipl cpcmd gets called when all other cpus are not running
anymore. To prevent deadlocks change __cpcmd so that it doesn't take
any locks and call cpcmd or __cpcmd, whatever is correct in the current
context.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

KEXEC_CONTROL_MEMORY_LIMIT is an unsigned long value and therefore
should be defined as one. Otherwise the kexec control page can be
allocated above 2GB which will cause a specification exception on the
sam31 instruction in the s390 kexec relocation code.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.

Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via

struct reset_call {
	struct reset_call *next;
	void (*fn)(void);
};

void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);

When the registered function get called the context is:

- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use

The registered functions may not take any locks are sleep.

For the common I/O layer part of this patch:

Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
  machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Get rid of our own user_termio_to_kernel_termios() and
kernel_termios_to_user_termio() macros which didn't check for errors
on user space accesses. Instead use the generic functions which
handle this properly.
In addition the generic version of user_termio_to_kernel_termios()
also copies the c_line member which was missing in our variant.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Follow other architectures and add __must_check to uaccess functions.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add missing bracket in definition for m48t35 RTC chip.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adds utility routines used by 52xx device drivers and board support
code.  Main functionality is to add device nodes to the of_platform_bus,
retrieve the IPB bus frequency, and find+ioremap device registers.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There is no need to expose these settings outside the scope
of the interrupt controller code itself.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

To allow arch/powerpc/kernel/crash.c to build on 32-bit we need a
definition of hard_irq_disable(). 32-bit doesn't support the lazy
interrupt disabling mechanism, so on 32-bit hard_irq_disable() is
simply local_irq_disable(). Add a definition for hard_irq_enable()
just for completeness.

This allows (KEXEC=y && PPC32=y) to build again. Broken since
d04c56f7.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.

If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At least the ide driver calls pcibus_to_node, which is not
defined when CONFIG_PCI is disabled. This adds a nop function
for the !PCI case.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.

Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.

The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.

I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

It may be desireable to build a kernel for cell without
spufs, e.g. as the initial kboot kernel. This requires
that the SPU specific parts of the core dump and the xmon
code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds a PS3 system bus driver.  This system bus is a virtual bus used to present
the PS3 system devices in the LDM.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds some needed bits for a config option PS3_USE_LPAR_ADDR that disables
the PS3 lpar address translation mechanism.  This is a currently needed
workaround for limitations in the design of the generic cell spu support.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds support for the PS3 repository.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds the needed firmware feature bits for the PS3.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds the PS3 hvcalls.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Adds the core platform support for the PS3 game console and other devices
using the PS3 hypervisor.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This adds a platform specific spu management abstraction and the coresponding
routines to support the IBM Cell Blade.  It also removes the hypervisor only
resources that were included in struct spu.

Three new platform specific routines are introduced, spu_enumerate_spus(),
spu_create_spu() and spu_destroy_spu().  The underlying design uses a new
type, struct spu_management_ops, to hold function pointers that the platform
setup code is expected to initialize to instances appropriate to that platform.

For the IBM Cell Blade support, I put the hypervisor only resources that were
in struct spu into a platform specific data structure struct spu_pdata.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This adds an accessor routine virq_to_hw() to the
virq routines which hides the implementation details
of the virq to hwirq map.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

It saves #ifdef'ing in callers if we at least define the 64-bit cpu
features for 32-bit also.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>