Since 9e6c643b (phy/fixed: use an unique MDIO bus name) the name of the fixed
PHY bus is "fixed-0". Teach of_phy_connect_fixed_link() the new name.

Tested on a P1020RDB PowerPC system.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

drivers/of/fdt.c included 'asm/setup.h' twice, remove the duplicate.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Temperature history is reset by writing 0x8000 into the peak temperature
register, not 0xffff.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed.  In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle.  Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Cc: Dirk Eibach <eibach@gdsys.de>
Acked-by: NJean Delvare <khali@linux-fr.org>

At least on powerpc, it breaks the build if exported functions are
static.  Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch fixes an unbalanced refcount issue.

Elevating the lock for both kref_put and also for controller node deletion.
Previously, controller deletion was protected but the not the kref_put. This
was causing the other thread to pick up the controller structure which was
already kref'd zero.

This was causing the following WARN_ON and also sometimes panic.

WARNING: at lib/kref.c:43 kref_get+0x2d/0x30() (Not tainted)
Hardware name: IBM System x3655 -[7985AC1]-
Modules linked in: fuse scsi_dh_rdac autofs4 nfs lockd fscache nfs_acl
auth_rpcgss sunrpc 8021q garp stp llc ipv6 ib_srp(U) scsi_transport_srp
scsi_tgt ib_cm(U) ib_sa(U) ib_uverbs(U) ib_umad(U) mlx4_ib(U) mlx4_core(U)
ib_mthca(U) ib_mad(U) ib_core(U) dm_mirror dm_region_hash dm_log dm_round_robin
dm_multipath uinput bnx2 ses enclosure sg ibmpex ibmaem ipmi_msghandler
serio_raw k8temp hwmon amd64_edac_mod edac_core edac_mce_amd shpchp i2c_piix4
ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif sata_svw pata_acpi ata_generic
pata_serverworks aacraid radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core
dm_mod [last unloaded: freq_table]
Pid: 13735, comm: srp_daemon Not tainted 2.6.32-71.el6.x86_64 #1
Call Trace:
[<ffffffff8106b857>] warn_slowpath_common+0x87/0xc0
[<ffffffff8106b8aa>] warn_slowpath_null+0x1a/0x20
[<ffffffff8125c39d>] kref_get+0x2d/0x30
[<ffffffffa01b4029>] rdac_bus_attach+0x459/0x580 [scsi_dh_rdac]
[<ffffffff8135232a>] scsi_dh_handler_attach+0x2a/0x80
[<ffffffff81352c7b>] scsi_dh_notifier+0x9b/0xa0
[<ffffffff814cd7a5>] notifier_call_chain+0x55/0x80
[<ffffffff8109711a>] __blocking_notifier_call_chain+0x5a/0x80
[<ffffffff81097156>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff8132bec5>] device_add+0x515/0x640
[<ffffffff813329e4>] ? attribute_container_device_trigger+0xc4/0xe0
[<ffffffff8134f659>] scsi_sysfs_add_sdev+0x89/0x2c0
[<ffffffff8134d096>] scsi_probe_and_add_lun+0xea6/0xed0
[<ffffffff8134beb2>] ? scsi_alloc_target+0x292/0x2d0
[<ffffffff8134d1e1>] __scsi_scan_target+0x121/0x750
[<ffffffff811df806>] ? sysfs_create_file+0x26/0x30
[<ffffffff8132b759>] ? device_create_file+0x19/0x20
[<ffffffff81332838>] ? attribute_container_add_attrs+0x78/0x90
[<ffffffff814b008c>] ? klist_next+0x4c/0xf0
[<ffffffff81332e30>] ? transport_configure+0x0/0x20
[<ffffffff813329e4>] ? attribute_container_device_trigger+0xc4/0xe0
[<ffffffff8134df40>] scsi_scan_target+0xd0/0xe0
[<ffffffffa02f053a>] srp_create_target+0x75a/0x890 [ib_srp]
[<ffffffff8132a130>] dev_attr_store+0x20/0x30
[<ffffffff811df145>] sysfs_write_file+0xe5/0x170
[<ffffffff8116c818>] vfs_write+0xb8/0x1a0
[<ffffffff810d40a2>] ? audit_syscall_entry+0x272/0x2a0
[<ffffffff8116d251>] sys_write+0x51/0x90
[<ffffffff81013172>] system_call_fastpath+0x16/0x1b
Signed-off-by: NBabu Moger <babu.moger@netapp.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

dpms bits not used on DCE4+
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If accel is not working many subsystem such as the ib pool might not be
initialized properly that can lead to segfault inside kernel when cs
ioctl is call with non working acceleration. To avoid this make sure
the accel working flag is false when an error in GPU startup happen and
return EBUSY from cs ioctl if accel is not working.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46274

Tested with a Cayman card in a Llano system: The additional files are created
and working for the Cayman card but not created for the CPU's built-in GPU.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We moved all our pSeries idle loops to the cpu idle framework
so we really want it to come up by default.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This provides unified readq()/writeq() helper functions for 32-bit
drivers.

For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly.  So in this patch, new two
header files which contain non-atomic readq/writeq are added.

 - <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
   writeq with the order of lower address -> higher address

 - <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
   writeq with reversed order

This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0a ("x86:
remove 32-bit versions of readq()/writeq()")

The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:

  #include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */

But this will be nop in 64-bit environments, and no other #ifdefs are
required.  So I believe that this patch can solve the problem of
 1. driver-specific readq/writeq
 2. atomicity and order of io access

This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.

Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This USB-serial cable with mini stereo jack enumerates as:
Bus 001 Device 004: ID 1a61:3410 Abbott Diabetes Care

It is a TI3410 inside.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer.  The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task.  Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.

The implementation in the 3.2 kernel suffers from an additional
problem.  There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.

The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue.  Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.

The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSeth Forshee <seth.forshee@canonical.com>
CC: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes.  The endpoint
descriptor has the NAK rate encoded in number of microframes.  We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct.  This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.

The fix is to use the correct encoding.  Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.

This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4a "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NFelipe Contreras <felipe.contreras@gmail.com>
Suggested-by: NAndiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org

The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.

Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.

The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI.  This allows the BIOS to access USB devices without
having xHCI support.

The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior.  The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.

Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished.  This will balance the ref counts in the PCI core.  When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.

This should be back ported to kernels as old as 2.6.31.  That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org

Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: NChris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: NRoland Stigge <stigge@antcom.de>

RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: NChris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: NRoland Stigge <stigge@antcom.de>

This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.

LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async().  Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended.  As one might expect, the outcome is not ideal.

This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them.  Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.

For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished.  It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that.  Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.

For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished.  The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.

To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().

[  299.281565] =============================================================================
[  299.281634] BUG kmalloc-4096 (Tainted: G          I ): Poison overwritten
[  299.281682] -----------------------------------------------------------------------------
[  299.281684]
[  299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[  299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[  299.281870] 	__slab_alloc+0x617/0x6c1
[  299.281901] 	__kmalloc+0x28c/0x2e0
[  299.281931] 	scsi_host_alloc+0x4a/0x490
[  299.281966] 	usb_stor_probe1+0x5b/0xc40 [usb_storage]
[  299.282010] 	storage_probe+0xa4/0xe0 [usb_storage]
[  299.282062] 	usb_probe_interface+0x172/0x330 [usbcore]
[  299.282105] 	driver_probe_device+0x257/0x3b0
[  299.282138] 	__driver_attach+0x103/0x110
[  299.282171] 	bus_for_each_dev+0x8e/0xe0
[  299.282201] 	driver_attach+0x26/0x30
[  299.282230] 	bus_add_driver+0x1c4/0x430
[  299.282260] 	driver_register+0xb6/0x230
[  299.282298] 	usb_register_driver+0xe5/0x270 [usbcore]
[  299.282337] 	0xffffffffa04ab03d
[  299.282364] 	do_one_initcall+0x47/0x230
[  299.282396] 	sys_init_module+0xa0f/0x1fe0
[  299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[  299.282482] 	__slab_free+0x3c/0x2a1
[  299.282510] 	kfree+0x296/0x310
[  299.282536] 	scsi_host_dev_release+0x18a/0x1d0
[  299.282574] 	device_release+0x74/0x100
[  299.282606] 	kobject_release+0xc7/0x2a0
[  299.282637] 	kobject_put+0x54/0xa0
[  299.282668] 	put_device+0x27/0x40
[  299.282694] 	scsi_host_put+0x1d/0x30
[  299.282723] 	do_scan_async+0x1fc/0x2b0
[  299.282753] 	kthread+0xdf/0xf0
[  299.282782] 	kernel_thread_helper+0x4/0x10
[  299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
      (null) flags=0x100000000004080
[  299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x          (null)
[  299.282884]
...
Signed-off-by: NHuajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: NShyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.

Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: NMichael Christie <mchristi@redhat.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: NOlatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This can cause instability in mailbox command state machine handling.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8.  This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state.  Consolidate the checks into
this inline-helper.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: NDan Melnic <dan@seamicro.com>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.

Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The 3215 driver calls tty_wakeup from irq context while holding the
device spinlock. If printk is called by any function on the callchain
starting from tty_wakeup the system deadlocks on the device spinlock.
Using a tasklet to call tty_wakup solves the problem.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

this function ins't needed anymore.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

with vblank_refcount = 1, there was the case that drm_vblank_put
is called by specific page flip function so this patch fixes the
issue.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

basically, all crtcs are possible to clone each other.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>