Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.

The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth.  If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth.  While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.

This patch implements an "off switch" as a module parameter.
Signed-off-by: NMichael Reed <mdr@sgi.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the number of request queues to the module paramater
ql2xmaxqueues.  Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process.  The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix kind-of-intr checking against number of interrupts
  microblaze: Update Microblaze defconfig

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: da903x: add missing __devexit_p()

Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):

    drivers/char/random.c: In function `get_random_int':
    drivers/char/random.c:1672: error: unrecognizable insn:
    (insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
            (subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
                        (subreg:DI (reg:SI 6 bp) 0))
                    (const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
        (nil))
    drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083

and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.

This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.

So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: NMartin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The problem is that permission checking is skipped if atomic open is
possible, but when exec opens a file, it just opens it O_READONLY which
means EXEC permission will not be checked at that time.

This problem is observed by the following sequence (executed as root):

  mount -t nfs4 server:/ /mnt4
  echo "ls" >/mnt4/foo
  chmod 744 /mnt4/foo
  su guest -c "mnt4/foo"
Signed-off-by: NFrank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Tested-by: NEugene Teo <eugeneteo@kernel.sg>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In Commit

commit 3b8b5c9b
Author: Eric Moore <eric.moore@lsi.com>
Date:   Tue Apr 21 15:44:27 2009 -0600

    [SCSI] mpt2sas : bump driver version to 01.100.02.00
 
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00.  Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: NEric Moore <eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Explicit alignment for .data.cacheline_aligned
  powerpc/ps3: Update ps3_defconfig
  powerpc/ftrace: Fix constraint to be early clobber
  powerpc/ftrace: Use pr_devel() in ftrace.c
  powerpc: Do not assert pte_locked for hugepage PTE entries

Merge branches 'sched-fixes-for-linus-2' and 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Fix fallback sched_clock()'s offset when using jiffies

* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: increase MAX_LOCKDEP_ENTRIES and MAX_LOCKDEP_CHAINS

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix performance regression caused by paravirt_ops on native kernels
  xen: use header for EXPORT_SYMBOL_GPL
  x86, 32-bit: fix kernel_trap_sp()
  x86: fix percpu_{to,from}_op()
  x86: mtrr: Fix high_width computation when phys-addr is >= 44bit
  x86: Fix false positive section mismatch warnings in the apic code

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Append prompt in /debug/tracing/README file
  x86/function-graph: fix constraint for recording old return value

Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.

That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).

The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().

Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.

Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Tested-by: NDaniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

`local_add_unless(x, y, z)' will be expanded to `(&(x)->y, (y), (x))', but
`&(x)->y' should be `&(x)->a'
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

+ Fix typographic fault.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Signed-off-by: NMichal Simek <monstr@monstr.eu>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.

So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Refresh and set these options:

 CONFIG_SYSFS_DEPRECATED_V2: y -> n
 CONFIG_INPUT_JOYSTICK:      y -> n
 CONFIG_HID_SONY:            n -> m
 CONFIG_RTC_DRV_PS3:         - -> m
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.

The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".

I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.

With CONFIG_DYNAMIC_DEBUG=y:

size before:
   text	   data	    bss	    dec	    hex	filename
   3334	    672	      4	   4010	    faa	arch/powerpc/kernel/ftrace.o

size after:
   text	   data	    bss	    dec	    hex	filename
   2616	    360	      4	   2980	    ba4	arch/powerpc/kernel/ftrace.o
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With CONFIG_DEBUG_VM, an assertion is made when changing the protection
flags of a PTE that the PTE is locked. Huge pages use a different pagetable
format and the assertion is bogus and will always trigger with a bug looking
something like

 Unable to handle kernel paging request for data at address 0xf1a00235800006f8
 Faulting instruction address: 0xc000000000034a80
 Oops: Kernel access of bad area, sig: 11 [#1]
 SMP NR_CPUS=32 NUMA Maple
 Modules linked in: dm_snapshot dm_mirror dm_region_hash
  dm_log dm_mod loop evdev ext3 jbd mbcache sg sd_mod ide_pci_generic
  pata_amd ata_generic ipr libata tg3 libphy scsi_mod windfarm_pid
  windfarm_smu_sat windfarm_max6690_sensor windfarm_lm75_sensor
  windfarm_cpufreq_clamp windfarm_core i2c_powermac
 NIP: c000000000034a80 LR: c000000000034b18 CTR: 0000000000000003
 REGS: c000000003037600 TRAP: 0300   Not tainted (2.6.30-rc3-autokern1)
 MSR: 9000000000009032 <EE,ME,IR,DR>  CR: 28002484  XER: 200fffff
 DAR: f1a00235800006f8, DSISR: 0000000040010000
 TASK = c0000002e54cc740[2960] 'map_high_trunca' THREAD: c000000003034000 CPU: 2
 GPR00: 4000000000000000 c000000003037880 c000000000895d30 c0000002e5a2e500
 GPR04: 00000000a0000000 c0000002edc40880 0000005700000393 0000000000000001
 GPR08: f000000011ac0000 01a00235800006e8 00000000000000f5 f1a00235800006e8
 GPR12: 0000000028000484 c0000000008dd780 0000000000001000 0000000000000000
 GPR16: fffffffffffff000 0000000000000000 00000000a0000000 c000000003037a20
 GPR20: c0000002e5f4ece8 0000000000001000 c0000002edc40880 0000000000000000
 GPR24: c0000002e5f4ece8 0000000000000000 00000000a0000000 c0000002e5f4ece8
 GPR28: 0000005700000393 c0000002e5a2e500 00000000a0000000 c000000003037880
 NIP [c000000000034a80] .assert_pte_locked+0xa4/0xd0
 LR [c000000000034b18] .ptep_set_access_flags+0x6c/0xb4
 Call Trace:
 [c000000003037880] [c000000003037990] 0xc000000003037990 (unreliable)
 [c000000003037910] [c000000000034b18] .ptep_set_access_flags+0x6c/0xb4
 [c0000000030379b0] [c00000000014bef8] .hugetlb_cow+0x124/0x674
 [c000000003037b00] [c00000000014c930] .hugetlb_fault+0x4e8/0x6f8
 [c000000003037c00] [c00000000013443c] .handle_mm_fault+0xac/0x828
 [c000000003037cf0] [c0000000000340a8] .do_page_fault+0x39c/0x584
 [c000000003037e30] [c0000000000057b0] handle_page_fault+0x20/0x5c
 Instruction dump:
 7d29582a 7d200074 7800d182 0b000000 3c004000 3960ffff 780007c6 796b00c4
 7d290214 7929a302 1d290068 7d6b4a14 <800b0010> 7c000074 7800d182 0b000000

This patch fixes the problem by not asseting the PTE is locked for VMAs
backed by huge pages.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

wb_kupdate() function has a bug on linux-2.6.30-rc5.  This bug causes
generic_sync_sb_inodes() to start to write inodes back much earlier than
our expectations because it miscalculates oldest_jif in wb_kupdate().

This bug was introduced in 704503d8
('mm: fix proc_dointvec_userhz_jiffies "breakage"').
Signed-off-by: NToshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: padlock - Revert aes-all alias to aes
  crypto: api - Fix algorithm module auto-loading
  crypto: eseqiv - Fix IV generation for sync algorithms
  crypto: ixp4xx - check firmware for crypto support

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: check sysdev_suspend(PMSG_FREEZE) return value

This adds CONFIG_REISERFS_FS_XATTR protection from reiserfs_permission.

This is needed to avoid warnings during file deletions and chowns with
xattrs disabled.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This avoids an Oops in open_xa_root that can occur when deleting a file
with xattrs disabled.  It assumes that the xattr root will be there, and
that is not guaranteed.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>