- 18 3月, 2015 5 次提交
-
-
由 Liad Kaufman 提交于
In 8000 HW family B-step only, the ICCM is separate from the SRAM. This adds the ICCM to the dump data collected for FW debug. Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
There are transport that must buffer frames in the driver. This means that we have frames that are not in the op_mode and not visible to the firwmare. This causes issues when we flush the queues: the op_mode flushes a queue, and the firmware flushes all the frames that are *currently* on the rings, but if the transport buffers frames, it can submit these while we are flushing. This leads to a situation where we still have frames on the queues after we flushed them. Preventing those buffered frame from getting into the firmware is possible, but then, we have to run the Tx response path on frames that didn't reach the firmware which is not desirable. The way I solve this here is to let these frames go to the firmware, but make sure the firmware will not transmit them (by setting the station as draining). The op_mode then needs to wait until the transport itself is empty to be sure that the queue is really empty. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Liad Kaufman 提交于
For each RX packet until this patch there only was a debug print of the HCMD and the offset. This adds also the sequence number of the packet for easier matching between what was sent, what came back / was received, and what got stuck somewhere and was never responded by the FW. Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
According to FW methodology, the capability bits should be the only ones that change per-HW. The API bits should remain constant across different HWs. Currently this is not the case with multi-source LAR (API bit 9). Assign a new capability bit to eventually replace the API bit. Until the API bit can be deprecated, the driver will check either to enable multi-source LAR. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
If, on a GO, the CSA time event fails to be scheduled, continue the flow towards mac80211's state machine so it doesn't get stuck, but report an error later on the post switch which will cause mac80211 to tear down the operation. This ensures nothing gets stuck due to the scheduling failure. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 12 3月, 2015 35 次提交
-
-
由 Emmanuel Grumbach 提交于
-
由 Johannes Berg 提交于
The return value in iwl_mvm_get_wakeup_status() is a bit unclear in that it's not obvious that we don't leak fw_status in some cases. Use fw_status directly with ERR_PTR() and return only it, that way the compiler has a chance of proving that it's uninitialized (if it ever is due to new changes.) Additionally, this removes a smatch warning since smatch couldn't figure out that fw_status can't, in fact, leak here. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after calling iwl_mvm_query_wakeup_reasons(), because this function unlocks it already. Move the goto out_iterate outside the #ifdef. Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
-
由 Johannes Berg 提交于
The code here is a little confusing, the iwl_mvm_te_check_disconnect() will check that the interface is a station, but going into it after already having processed the time even end for P2P seems strange at first look. Put a switch statement there to distinguish the interface types and make this more readable. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
We previously enabled the smart FIFO (SF) in BSS only after association. This cause interrupt latency on P2P on certain devices. Change the working model to enable the SF all the time and play with the timeout values based on the association state. This change was not tested on older firwmares, so make it happen only on -13.ucode and up. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Oren Givon 提交于
More sub system IDs were introduced for the 8260 series. Add the new sub system IDs so the cards can be recognized. Signed-off-by: NOren Givon <oren.givon@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The firmware was not using the new API, so we don't need to differentiate between the different stages of this new API. The main difference here is that most of the hard coded values are not sent through the command anymore. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The newer devices will enable a new register for this (DEVICE_SET_NMI_8000B_REG), but the interrupt handler isn't wired yet. Keep the old register for now. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
When a station goes to sleep, we can't transmit any frame to it. This means that until that station will wake up, a queue that is dedicated to this station won't progress at all. Take this into account when monitoring stuck queues and don't account for the time the station was asleep. This allows to mask false positives where the queues are stuck not because of a bug, but because of the station being asleep. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This allows the op_mode to let the transport know that a queue is currently frozen and that its timer should be stopped. When the queue is unfrozen, its timer should be set to expire after the remainder of the timeout has elapsed. This can be used when stations go to sleep. When a station goes to sleep, the op_mode can freeze the timer so that the queue will never be considered as stuck. When the station wakes up, the queue will be unfrozen. This is meant to avoid false positives that would happen if a buggy station goes to sleep for a very long time. In case we have a dedicated queue for this station (BA agreement) and it goes to sleep for a very long time, the queue would rightfully be stopped during all that time. In this case, the stuck queue timer could fire and that would be a false positive. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
The Tx statistics weren't updated when using fixed rate for debugging. Fix this as Tx statistics are useful in this use case. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
RTNL is not taken during CT-kill so regulatory APIs cannot be invoked. That's fine, since the HW is only brought up to check the temperature during CT-kill. We don't expect Tx or scanning. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
When using IBSS, it's easily possible to exhaust the number of available stations in the driver, so don't warn on it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
When we load the firmware for the 8000 B step device, it'll verify its signature. In the current version of the hardware, there can be a race between the WiFi firmware being loaded and the Bluetooth firmware being loaded. Check that WiFi is authenticated, if not, take ownership on the authentication machine to make sure that the WiFi firmware will be authenticated. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Oren Givon 提交于
New sub system IDs were introduced for the 8260 series. This patch adds them so new 8260 cards can be recognized. Signed-off-by: NOren Givon <oren.givon@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
Make the print a bit more readable. Reported-by: NJoe Perches <joe@perches.com> Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
If the FW returns an invalid channels count in response to an MCC request, make sure we don't reference invalid indices in the channels array. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
When entering D0i3, the MVM mutex cannot be grabbed. This interferes with the calculation of the number of connected TDLS stations during the setup of the power cmd. The goal is to disable power saving for all vifs while any TDLS station is connected. For this purpose it is enough to keep the pm_enabled member of all mvmvifs as false. An update of the power state already occurs when a TDLS station is added/removed, so the values are correctly updated. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
mvm->fw->dbg_dest_tlv really needs to be under the right parenthesis. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The functions related to firmware error dump moved. No need for this unclude anymore. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
New NVM versions in LnP platforms have the lar_enable bits in a different offset. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
While at it, fix a few checkpatch issues. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This adds BT Coex data to the prph register list. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
We don't need to acquire MAC access for each access, it makes much more sense to keep the MAC access. This speeds up the Tx DMA stop flow significantly. Moreover, if one channel can't be stopped, stop the others but don't poll for them to avoid being stuck there for a long time. This solves a situation in which we were stuck in that flow for way too long with a spinlock held which led to a kernel panic. Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
In-order to recognize newer step of the device, the driver must read the chip_version_id from the AUX bus MISC address space. This will determine what firmware file will be loaded. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
When we associate we always need to update the quotas. This fixes a bug for cases in which quotas weren't udapted after association. Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Enable this feature only if the firmware advertises support for it. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
All the supported firmwares support this API. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
All the supported firwmares have this new API. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This new firmware will come out soon. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Jonathan Doron 提交于
When moving to the D3 FW give it the valid MCC from the D0 FW. When returning from D3 to D0, query the D3 FW for the latest MCC, as it might have changed internally. This MCC will be replayed to the D0 FW when it boots. Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Jonathan Doron 提交于
When booting the card, check for a dedicated regulatory ACPI entry. If such exists, read it and give the information to FW with the appropriate source. Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com> Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
For some configurations, the driver should get the MAC address from the hardware registers and not from the regular locations. Since the parsing of the MAC address is the same regardless of its source, continue the regular code path (parsing) after we read the registers. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
This module parameter is useful for debugging NVM and LAR related issues. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-