Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 06 5月, 2007 4 次提交
    • S
      cmd64x: interrupt status fixes (take 2) · e51e2528
      由 Sergei Shtylyov 提交于 
      The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      e51e2528
    • S
      cmd64x: fix multiword and remove single-word DMA support · 60e7a82f
      由 Sergei Shtylyov 提交于 
      Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      60e7a82f
    • S
      sl82c105: DMA support code cleanup (take 4) · 688a87d1
      由 Sergei Shtylyov 提交于 
      Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      688a87d1
    • S
      sl82c105: rework PIO support (take 2) · e93df705
      由 Sergei Shtylyov 提交于 
      Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly  simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      e93df705
  3. 05 5月, 2007 36 次提交