Currently MMC core will keep going if HS200/HS timing switch failed
with -EBADMSG error by the assumption that the old timing is still valid.

However, for mmc_select_hs200 case, the signal voltage may have already
been switched. If the timing switch failed, we should fall back to
the old voltage in case the card is continue run with legacy timing.

If fall back signal voltage failed, we explicitly report an EIO error
to force retry during the next power cycle.
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

CMD0 or hardware reset may invalidate the cache, so it needs to be
flushed before reset.

In the case of recovery, we can't expect flushing the cache to work
always, but have a go and ignore errors.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This if-block is going to call mmc_card_set_blockaddr(), so
mmc_card_blockaddr() right before it is redundant.

I am fixing the block comment style while I am here.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eMMC HW reset may be implemented either via the host ops ->hw_reset()
callback or through DT and the eMMC pwrseq. Additionally some eMMC cards
don't support HW reset.

To allow a reset to be done for the different combinations of mmc hosts
and eMMC/MMC cards, let's implement a fallback via trying a regular power
cycle. This improves the mmc block layer retry mechanism of failing I/O
requests.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
[Ulf: Rewrote changelog]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bus width is sometimes the actual bus width, and sometimes indices
to different arrays encoding the bus width. In my debugging case "2"
could mean 8-bit as well as 4-bit, which was extremly confusing. Let's
use the human-readable actual bus width in all places.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

IMO this info is only useful for developers. Most users won't need this
information, since there is not much they can do about it.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit cc4f414c ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode.  While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: NWenkai Du <wenkai.du@intel.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS).  The problem is that it does that
using the timing settings of the previous mode.  That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command.  Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode.  Thus the HS timings should be set
only after the card has switched mode.

However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode.  That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.

A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming  it, so reclaim the host  only in case
of success.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.

Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.

To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: NAdrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.

Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

card->ext_csd.enhanced_area_offset is defined as "unsigned long long",
and, ext_csd[] is defined as u8.
unsigned long long data might have strange data if first bit of ext_csd[]
was 1. this patch cast it to (unsigned long long)
Special thanks to coverity <http://www.coverity.com>

ex)
        u8  data8;
        u64 data64;

        data8 = 0x80;
        data64 = (data8 << 24); // 0xffffffff80000000
        data64 = (((unsigned long long)data8) << 24); // 0x80000000;
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

HS400 re-tuning must be done in HS200 mode. Add
the ability to switch from HS400 mode to HS200
mode before re-tuning and switch back to HS400
after re-tuning.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sleep command is issued after deselecting the
card, but re-tuning won't work on a deselected card
so re-tuning must be held.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:

		mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
 				EXT_CSD_HPI_MGMT, 1,
 				card->ext_csd.generic_cmd6_time);

There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch fix spelling typo in printk messages.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch is coming to fix compatibility issue of BKOPS_EN  field of EXT_CSD.
In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits:
Bit 0 - MANUAL_EN
Bit 1 - AUTO_EN
In previous eMMC revisions, only Bit 0 was supported.
Signed-off-by: NAlexey Skidanov <alexey.skidanov@sandisk.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: NJohan Rudholm <johanru@axis.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.

Those are now intended to be used only by the mmc core.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>

In (3fcb027d ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added.  According to
the original change it was "for now only called from
mmc_sdio_init_card()".

This callback really ought to be called from the SD and MMC init
functions as well.  One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in.  Specifically the
normal SD card will not get to run with 4-bit data.

I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set

Fixes: 577fb131 (mmc: rework selection of bus speed mode)
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of doing BUG_ON(), return an error code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.

Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Rely on the prints handled internally by kmalloc().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the MMC spec version is < CSD_SPEC_VER_4, there aren't support for
the EXT_CSD register. Since max_dtr is fetched from there, it will
default to zero, which thus isn't needed to verify.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The validation of the buswidth and the MMC spec version in
__mmc_select_powerclass() is redundant, let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let callers of mmc_free_ext_csd() do kfree() directly instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>