Now that we have sensibly split up, we can nicely get rid of that ugly
is_gen5 check.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by Ben Widawsky's patch for gen6+. Now after restructuring
how we set up the ring vtables and parameters, we can do this right.

This kills the bsd specific get/put_irq functions, they're now the
same.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The waiter is always the ring itself (otherwise we'd have a decent
snafu in a callsite), so we can unify this easily.

Also give it the usual gen6_ prefix, in case anyone is foolish enough to
implement hw semaphores for gen5.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not supported, and with the patch to refuse loading on gen6+
without kms enabled, there's also no way we can hit this.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just for consistency.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The same treatment for the bsd ring. Again, this will be split up
further by the irq rework.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our hw is simply not well-designed enough that it neatly fits into
boxes. Everywhere else we set up vtables and similar things
dynamically using switch statements - it's simply much more flexible.

This is prep work to rework the pre-gen6 ring irq stuff - it'll add a
few more differences. With the current const struct templates, that
would be a mess.

This leads to some unfortunate duplication with the old dri1 code, but
we can reap that again because gen6 isn't actually supported there.
But that's for a separate patch.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Eventually we want to scale the ring size depending upon available
gtt space. For now just consolidate this instead of replicating it
over all ringbuffer templates.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only ever enable/disable one interrupt (namely user_interrupts and
pipe_notify), so we don't need to track the interrupt masking state.

Also rename irq_enable to irq_enable_mask, now that it won't collide -
beforehand both a irq_mask and irq_enable_mask would have looked a bit
strange.
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Waiting for seqno-1 in our object synchronization code is an
implementation detail given how we've decided to do the waits within the
rest of our code.
Requested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This fixes a long standing issue where emitting the semaphore updates
may have failed, but we've already updated our internal data structure.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When I extracted the synchronization code for implementing semaphorified
pageflips (74f5f6e0), I neglected the non pipelined case which also
calls this code. The modesetting code wants to make sure the object has
finished rendering to the frame before configuring the scanout (ie.
non-pipelined case).

As a result of a follow on discussion on IRC, I've decided to add a
comment about the function itself which received much inspiration from
Chris as well. So really, this patch was ghost-written by Chris :).
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On IVB, there are two sets of panel backlight regs: one in the CPU and
one in the PCH.  The CPU ones aren't generally used, so on IVB make sure
we allow the PCH regs to actually control the backlight.

v2: remove unused pwm variable (Daniel)
    move to init_hw function so we override on resume too
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We'll probably need new init functions and will need to test it.

v2: fix impossible GEN6 && GEN7 condition, move to Daniel's new init function
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If these regs don't have valid values, the panel won't come up, and may
even cause a system hang.  So do a basic sanity check when an eDP panel
is detected.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44305Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After a gpu reset we need to re-init some of the hw state we only
initialize when modeset is enabled, like rc6, hw contexts or render/GT
core clock gating and workaround register settings.

Note that this patch has a small change in the resume code:
- rc6 on gen6+ is only restored for the modeset case (for more
  consistency with other callsites). This is no problem because recent
  kernels refuse to load drm/i915 without kms on gen6+
- rc6/emon on ilk is only restored for the modeset case. This is no
  problem because rc6 is disabled by default on ilk, and ums on ilk
  has never really been a supported option outside of horrible rhel
  backports.

v2: Chris Wilson noticed that we not only fail to restore the clock
gating settings after gpu reset.

v3: Move the call to modeset_init_hw in _reset out of the
struct_mutext protected area - other callers don't hold it, too.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similar to allowing a buffer to be simultaneously read by the GPU and
through the GTT, we wish to allow readback of the pages through the CPU
domain whilst they are also being read by the GPU. Domain coherency
is managed by allowing multiple readers, but only a single writer.

This is used by mesa for its program cache which it may search for every
new program every frame and then renews should it need to add. During
renewal, mesa copies the program bo currently executing through a CPU
mapping onto the new bo. This patch allows the search and that copy to
proceed without causing a stall on the current batch.

Testcase: i-g-t/tests/gem_cpu_concurrent_blit
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't need the pt_addr for the !dmar case, so drop the else and
move the if (dmar) condition out of the loop.

v2: Fixup whitespace damage noticed by Chris Wilson.

v3: Collapse the two identical if blocks. Chris Wilson makes me look
like a moron right now ...
Noticed-by: NKonstantin Belousov <kostikbel@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wislon.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both PCH and CPU eDP are DP, so set the is_dp flag to true.  Add
is_cpu_edp and is_pch_edp bools to make checking for each less verbose
(rather than has_edp_encoder && !intel_encoder_is_pch_edp() sprinkled
everywhere).  And rename the "has_edp_encoder" variable to just
"edp_encoder".

With the above variables cleaned up, the rest of the code becomes a bit
more readable and clear.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Merge rc6 information into the power group for our device. Until now the
i915 driver has not had any sysfs entries (aside from the connector
stuff enabled by drm core). Since it seems like we're likely to have
more in the future I created a new file for sysfs stubs, as well as the
rc6 sysfs functions which don't really belong elsewhere (perhaps
i915_suspend, but most of the stuff is in intel_display,c).

displays rc6 modes enabled (as a hex mask):
cat /sys/class/drm/card0/power/rc6_enable

displays #ms GPU has been in rc6 since boot:
cat /sys/class/drm/card0/power/rc6_residency_ms

displays #ms GPU has been in deep rc6 since boot:
cat /sys/class/drm/card0/power/rc6p_residency_ms

displays #ms GPU has been in deepest rc6 since boot:
cat /sys/class/drm/card0/power/rc6pp_residency_ms

Important note: I've seen on SNB that even when RC6 is *not* enabled the
rc6 register seems to have a random value in it. I can only guess at the
reason reason for this. Those writing tools that utilize this value need
to be careful and probably want to scrutinize the value very carefully.

v2: use common rc6 residency units to milliseconds for the other RC6 types

v3: don't create sysfs files for GEN <= 5
add a rc6_enable to show a mask of enabled rc6 types
use unmerge instead of remove for sysfs group
squash intel_enable_rc6() extraction into this patch

v4: rename sysfs files (Chris)

CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>f
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: squash in the 64bit division fix by Chris Wilson.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Well, almost. Just a couple of differences, Ironlake lacks a few of the
RGB formats, only exposing x8r8g8b8, and lacks a couple of unused
features. Given the similarities, we can then reuse the same routines as
already written for Sandybridge to enable overlay support for Ironlake as
well.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The POSTING_READ() calls were originally added to make sure the writes
were flushed before any timing delays and across loops.
Now that the code has settled a bit, let's remove them.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Save the GMBUS2 value read while polling for state changes, and then
reuse this value when determining for which reason the loops were exited.
This is a small optimization which saves a couple of bus accesses for
memory mapped IO registers.

To avoid "assigning in if clause" checkpatch errors", use a ret variable
to store the wait_for macro return value.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It is very common for an i2c device to require a small 1 or 2 byte write
followed by a read.  For example, when reading from an i2c EEPROM it is
common to write and address, offset or index followed by a reading some
values.

The i915 gmbus controller provides a special "INDEX" cycle for performing
such a small write followed by a read.  The INDEX can be either one or two
bytes long.  The advantage of using such a cycle is that the CPU has
slightly less work to do once the read with INDEX cycle is started.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The i915 is only able to generate a STOP cycle (i.e. finalize an i2c
transaction) during a DATA or WAIT phase.  In other words, the
controller rejects a STOP requested as part of the first transaction in a
sequence.

Thus, for the first transaction we must always use a WAIT cycle, detect
when the device has finished (and is in a WAIT phase), and then either
start the next transaction, or, if there are no more transactions,
generate a STOP cycle.

Note: Theoretically, the last transaction of a multi-transaction sequence
could initiate a STOP cycle.  However, this slight optimization is left
for another patch.  We return -ETIMEDOUT if the hardware doesn't
deactivate after the STOP cycle.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
[danvet: added comment to the code that gmbus can't generate STOP on
the very first cycle.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GMBUS controller can report a NAK condition while a transaction is
still active. If the driver is fast enough, and the bus is slow enough,
the driver may clear the NAK condition while the controller is still
busy, resulting in a confused GMBUS controller.  This will leave the
controller in a bad state such that the next transaction may fail.

Also, return -ENXIO if a device NAKs a transaction.

Note: this patch also refactors gmbus_xfer to remove the "done" label.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GMBUS controller GMBUS3 register is double-buffered.  Take advantage
of this  by writing two 4-byte words before the first wait for HW_RDY.
This helps keep the GMBUS controller from becoming idle during long writes.

In fact, during experiments using the GMBUS interrupts, the HW_RDY
interrupt would only trigger for transactions >4 bytes after 2 writes
to GMBUS3.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A common method of probing an i2c bus is trying to do a zero-length write.
Handle this case by checking the length first before decrementing it.

This is actually important, since attempting a zero-length write is one
of the ways that i2cdetect and i2c_new_probed_device detect whether
there is device present on the bus with a given address.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just noticed this while verifying the VGA disable code.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In theory this will have performance and power improvements. Performance
because we don't need to stall when the scanout BO is busy, and power
because we don't have to stall when the BO is busy (and the ring can
even go to sleep if the HW supports it).

v2:
squash 2 patches into 1 (me)
un-inline the enable_semaphores function (Daniel)
remove comment about SNB hangs from i915_gem_object_sync (Chris)
rename intel_enable_semaphores to i915_semaphore_is_enabled (me)
removed page flip comment; "no why" (Chris)

To address other comments from Daniel (irc):
update the comment to say 'vt-d is crap, don't enable semaphores'
  - I think you misinterpreted Chris' comment, it already exists.
checking out whether we can pageflip on the render ring on ivb (didn't
work on early silicon)
  - We don't want to enable workarounds for early silicon unless we have
    to.
  - I can't find any references in the docs about this.
optionally use it if the fb is already busy on the render ring
  - This should be how the code already worked, unless I am
    misunderstanding your meaning.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By simplifying the rules to calling get_fence when writing to the
through the GTT in a tiled manner, and calling put_fence before writing
to the object through the GTT in a linear manner, the code becomes
clearer and there is less chance of making a mistake.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[danvet: fixed up conflict with ppgtt code and spelling in a new
comment.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

RC6 residency should be in intervals of 1.28us, and the counter wraps.
Here is an example using awk to get the various RC6 and RC6+ residency
times in seconds, since boot.

cat /sys/kernel/debug/dri/0/i915_drpc_info  | grep residency | awk -F':' -F' '  '{print $5 * 1.28 / 1000000}'

This is primarily for QA, but has other applications as well. An
upcoming patch to add interfaces should be more interesting to
application developers.

v2: move comment to the correct place

v3: display with %u instead of %d, for Ouping

CC: Ouping Zhang <ouping.zhang@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
 ids are not yet added, and there's still quite a few patches to merge
 (mostly modesetting). To make QA easier I've decided to merge this stuff
 in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
 is a real frankenstein chip, but also hsw is stretching our driver's
 code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
 there are more patches needed (and some already queued up), but I wanted
 to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
 a few months already and a lot of i-g-t tests have been created for it.
 Now it's finally ready to be merged.  Note that one patch in this series
 touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
 Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
 driver we actually need to support by bailing out of unsupported case.
 The driver now refuses to load without kms on gen6+ and disallows a few
 ioctls that userspace never used in certain cases. More of this will
 definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
 in this way).
- Small fixlets and adjustements and some minor things to help debugging.

Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."

* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
  drm/i915: VCS is not the last ring
  drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
  drm/i915: make quirks more verbose
  drm/i915: dump the DMA fetch addr register on pre-gen6
  drm/i915/sdvo: Include YRPB as an additional TV output type
  drm/i915: disallow gem init ioctl on ilk
  drm/i915: refuse to load on gen6+ without kms
  drm/i915: extract gt interrupt handler
  drm/i915: use render gen to switch ring irq functions
  drm/i915: rip out old HWSTAM missed irq WA for vlv
  drm/i915: open code gen6+ ring irqs
  drm/i915: ring irq cleanups
  drm/i915: add SFUSE_STRAP registers for digital port detection
  drm/i915: add WM_LINETIME registers
  drm/i915: add WRPLL clocks
  drm/i915: add LCPLL control registers
  drm/i915: add SSC offsets for SBI access
  drm/i915: add port clock selection support for HSW
  drm/i915: add S PLL control
  drm/i915: add PIXCLK_GATE register
  ...

Conflicts:
	drivers/char/agp/intel-agp.h
	drivers/char/agp/intel-gtt.c
	drivers/gpu/drm/i915/i915_debugfs.c

On coherent systems (not-AGP) the IB should be in cached memory so should
be just as fast, so we can avoid copying to temporary pages and just use it
directly.

provides minor speedups on rv530: gears ~1820->1860, ipers: 29.9->30.6,
but always good to use less CPU if we can.

v3: cleanup unneeded bits.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This closes a race seen with kexec where we enable PCI bus mastering
but the card has been reinitialised fully yet.

This was previously fixed by a patch from Jerome, but this should
close the race completely.

v2: add SI support as suggested by Alex.
Reported-and-tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I made a mistake, please forgive me.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48254Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When booting with EFI, Apple botched this one up.

v2: Switch the quirk dmesg output to DRM_INFO.
v3: Actually git add the new things ...
Tested-by: NAustin Lund <austin.lund@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42842Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And add informational dmesg output where it does not yet exist.

In case a quirk matches too much, this information is crucial for
debugging such a bug report.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reported-and-tested-by: Bo Wang < bo.b.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36997Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>