- 24 7月, 2010 5 次提交
-
-
由 Ursula Braun 提交于
When creating a claw device, just 2 subchannels have to be grouped. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
If qeth issues an ipa command, but for some reasons the response never comes back, qeth reaches a timeout. Reset the irq_pending flag of the write channel in timeout handling code and trigger a recovery to avoid endless looping for the following ipa command. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
This patch serializes device removal and other sysfs-triggered configurations by moving removal of sysfs-attributes to the beginning of the remove functions. And it serializes online/offline setting and discipline-switching (causing reestablishing of the net_device) by making use of a new discipline mutex. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Carsten Otte 提交于
This patch fixes a problem that occurs when switching from layer 3 to layer 2 mode. Resetting this mac_bits makes sure that we retrieve our mac address from the card, otherwise the interface simply would'nt work. Signed-off-by: NCarsten Otte <cotte@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Klaus-Dieter Wacker 提交于
The qeth IP address flag setting is possible when device is offline. When setting device online afterwards the current set IP addresses have to be correctly registered with the device regarding the IP address takeover attribute. Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 7月, 2010 8 次提交
-
-
由 Dan Carpenter 提交于
If the allocations fail in either dwmac1000_setup() or dwmac100_setup() then return NULL. These are called from stmmac_mac_device_setup(). The check for NULL returns in stmmac_mac_device_setup() needed to be moved forward a couple lines. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
Negate has precedence over comparison so the original assert only checked that "rfml->fragment_size" was larger than 1 or 0. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jay Vosburgh 提交于
When copying VLAN information to or removing from a slave during slave addition or removal, the bonding code currently holds the bond->lock for write to prevent concurrent modification of the vlan_list / vlgrp. This is unnecessary, as all of these operations occur under RTNL. Holding the bond->lock also caused might_sleep issues for some drivers' ndo_vlan_* functions. This patch removes the extra locking. Problem reported by Michael Chan <mchan@broadcom.com> Signed-off-by: NJay Vosburgh <fubar@us.ibm.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jay Vosburgh 提交于
After commit ad1afb00 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)") it is now regular practice for a VLAN "add vid" for VLAN 0 to arrive prior to any VLAN registration or creation of a vlan_group. This patch updates the bonding code that tests for the presence of VLANs configured above bonding. The new logic tests for bond->vlgrp to determine if a registration has occured, instead of testing that bonding's internal vlan_list is empty. The old code would panic when vlan_list was not empty, but vlgrp was still NULL (because only an "add vid" for VLAN 0 had occured). Bonding still adds VLAN 0 to its internal list so that 802.1p frames are handled correctly on transmit when non-VLAN accelerated slaves are members of the bond. The test against bond->vlan_list remains in bond_dev_queue_xmit for this reason. Modification to the bond->vlgrp now occurs under lock (in addition to RTNL), because not all inspections of it occur under RTNL. Additionally, because 8021q will never issue a "kill vid" for VLAN 0, there is now logic in bond_uninit to release any remaining entries from vlan_list. Signed-off-by: NJay Vosburgh <fubar@us.ibm.com> Cc: Pedro Garcia <pedro.netdev@dondevamos.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wolfram Sang 提交于
After the change from mdio polling to irq, it became necessary to restore the interrupt mask after resetting the chip in fec_stop(). Otherwise, with all irqs disabled, no communication with the PHY will be possible after e.g. un-/replugging the cable and the device gets stalled. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Kulikov Vasiliy 提交于
pci_iomap() can fail, handle this case and return -ENOMEM from probe function. Signed-off-by: NKulikov Vasiliy <segooon@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Add a new rt attribute, RTA_MARK, and use it in rt_fill_info()/inet_rtm_getroute() to support following commands : ip route get 192.168.20.110 mark NUMBER ip route get 192.168.20.108 from 192.168.20.110 iif eth1 mark NUMBER ip route list cache [192.168.20.110] mark NUMBER Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marc Kleine-Budde 提交于
This core is found on some Freescale SoCs and also some Coldfire SoCs. Support for Coldfire is missing though at the moment as they have an older revision of the core which does not have RX FIFO support. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de> Acked-by: NWolfgang Grandegger <wg@grandegger.com> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
- 22 7月, 2010 8 次提交
-
-
由 David S. Miller 提交于
Reported by Stephen Rothwell. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Reported by Stephen Rothwell. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gustavo F. Padovan 提交于
Network code uses the __packed macro instead of __attribute__((packed)). Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gustavo F. Padovan 提交于
Remove IRDA_PACKED macro, which maps to __attribute__((packed)). IRDA is one of the last users of __attribute__((packet)). Networking code uses __packed now. Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Kulikov Vasiliy 提交于
Use for_each_pci_dev() to simplify the code. Signed-off-by: NKulikov Vasiliy <segooon@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Add and use a few neatening macros Remove PFX Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt Convert printk(KERN_ERR to pr_err( $ size drivers/net/qlge/built-in.o.* text data bss dec hex filename 116456 2312 25712 144480 23460 drivers/net/qlge/built-in.o.old 114909 2312 25728 142949 22e65 drivers/net/qlge/built-in.o.new Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
There are two initializations of ndo_set_mac_address, one to a local function that is not used otherwise and one to a function that is defined elsewhere. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ identifier I, s, fld; position p0,p; expression E; @@ struct I s =@p0 { ... .fld@p = E, ...}; @s@ identifier I, s, r.fld; position r.p0,p; expression E; @@ struct I s =@p0 { ... .fld@p = E, ...}; @script:python@ p0 << r.p0; fld << r.fld; ps << s.p; pr << r.p; @@ if int(ps[0].line)<int(pr[0].line) or int(ps[0].column)<int(pr[0].column): cocci.print_main(fld,p0) // </smpl> akpm: - Use the standard eth_mac_addr() in uml_net_set_mac() - Remove unneeded and racy local set_ether_mac() - Remove duplicated (and incorrect) uml_netdev_ops.ndo_set_mac_address initializer. Fixes 8bb95b39 ("uml: convert network device to netdevice ops"). [akpm@linux-foundation.org: rework as above] Signed-off-by: NJulia Lawall <julia@diku.dk> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Shevchenko 提交于
Get rid of own implementation of hex_to_bin(). Signed-off-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com> Acked-by: NDivy Le Ray <divy@chelsio.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 7月, 2010 8 次提交
-
-
由 David S. Miller 提交于
Conflicts: drivers/vhost/net.c net/bridge/br_device.c Fix merge conflict in drivers/vhost/net.c with guidance from Stephen Rothwell. Revert the effects of net-2.6 commit 573201f3 since net-next-2.6 has fixes that make bridge netpoll work properly thus we don't need it disabled. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Horman 提交于
Convert a few calls from kfree_skb to consume_skb Noticed while I was working on dropwatch that I was detecting lots of internal skb drops in several places. While some are legitimate, several were not, freeing skbs that were at the end of their life, rather than being discarded due to an error. This patch converts those calls sites from using kfree_skb to consume_skb, which quiets the in-kernel drop_monitor code from detecting them as drops. Tested successfully by myself Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Horman 提交于
Patch to add -EAGAIN error to dropwatch netlink message handling code. -EAGAIN will be returned anytime userspace attempts to transition the state of the drop monitor service to a state that its already in. That allows user space to detect this condition, so it doesn't wait for a success ACK that will never arrive. Tested successfully by me Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Casey Leedom 提交于
Adding myself as the official maintainer of the Chelsio T4 Virtual function Driver (cxgb4vf). Signed-off-by: NCasey Leedom <leedom@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Casey Leedom 提交于
Fix bug in setup_sge_queues() where we were incorrectly only allocating a single "Queue Set" for MSI mode. Signed-off-by: NCasey Leedom <leedom@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Casey Leedom 提交于
Fix off-by-one error in checking for the end of the mailbox response delay array. We ended up walking off the end and, if we were unlucky, we'd end up pulling in a 0 and never terminate the mailbox response delay loop ... Signed-off-by: NCasey Leedom <leedom@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 7月, 2010 11 次提交
-
-
由 Herbert Xu 提交于
The new netpoll code in bridging contains use-after-free bugs that are non-trivial to fix. This patch fixes this by removing the code that uses skbs after they're freed. As a consequence, this means that we can no longer call bridge from the netpoll path, so this patch also removes the controller function in order to disable netpoll. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Thanks, Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Even with jumbograms I cannot see any way in which we would need to records a larger than 65535 valued next-header offset. The maximum extension header length is (256 << 3) == 2048. There are only a handful of extension headers specified which we'd even accept (say 5 or 6), therefore the largest next-header offset we'd ever have to contend with is something less than say 16k. Therefore make it a u16 instead of a u32. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
smp_mb() inside bnx2_tx_avail() is used twice in the normal bnx2_start_xmit() path (see illustration below). The full memory barrier is only necessary during race conditions with tx completion. We can speed up the tx path by replacing smp_mb() in bnx2_tx_avail() with a compiler barrier. The compiler barrier is to force the compiler to fetch the tx_prod and tx_cons from memory. In the race condition between bnx2_start_xmit() and bnx2_tx_int(), we have the following situation: bnx2_start_xmit() bnx2_tx_int() if (!bnx2_tx_avail()) BUG(); ... if (!bnx2_tx_avail()) netif_tx_stop_queue(); update_tx_index(); smp_mb(); smp_mb(); if (bnx2_tx_avail()) if (netif_tx_queue_stopped() && netif_tx_wake_queue(); bnx2_tx_avail()) With smp_mb() removed from bnx2_tx_avail(), we need to add smp_mb() to bnx2_start_xmit() as shown above to properly order netif_tx_stop_queue() and bnx2_tx_avail() to check the ring index. If it is not strictly ordered, the tx queue can be stopped forever. This improves performance by about 5% with 2 ports running bi-directional 64-byte packets. Reviewed-by: NBenjamin Li <benli@broadcom.com> Reviewed-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Based on original patch by Breno Leitão <leitao@linux.vnet.ibm.com>. Allocate the actual number of vectors and make use of fewer vectors if pci_enable_msix() returns > 0. We must allocate one additional vector for the cnic driver. Cc: Breno Leitão <leitao@linux.vnet.ibm.com> Reviewed-by: NBenjamin Li <benli@broadcom.com> Reviewed-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
We were using the wrong tx multicast counter instead of the rx multicast counter. Reported-by: NPeter Snellman <peter.snellman@cinnober.com> Reviewed-by: NBenjamin Li <benli@broadcom.com> Reviewed-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Don Skidmore 提交于
Bump the version string to better reflect what is in the driver. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
The FCoE protocol stack may hold a lock when this gets called. Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
When FCoE is disabled, there is a race condition that FCoE offload is turned off but the FCoE protocol driver is still queuing I/O thinking offload support still exists. This patch toggles off corresponding FCoE netdev feature flags and notify the FCoE stack first, allowing FCoE protocol stack driver to update its flags upon NETDEV_FEAT_CHANGE so no I/O will be using offload. Also, indicate FCoE offload flags in vlan_features in ixgbe_probe once and do not toggle them in ixgbe_fcoe_enable/disable so when FCoE is created on the VLAN interface, vlan_transfer_features() would properly update the VLAN netdev features flag and notify the FCoE protocol driver for NETDEV_FEAT_CHANGE. Signed-off-by: NYi Zou <yi.zou@intel.com> Tested-by: NRoss Brattain <ross.b.brattain@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change removes UDP from the supported protocols for RSS hashing. The reason for removing this protocol is because IP fragmentation was causing a network flow to be broken into two streams, one for fragmented, and one for non-fragmented and this in turn was causing out-of-order issues. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Acked-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
Set the DPF bit when PFC is enabled. This will discard PFC frames so they do not get passed up the stack. The DPF bit is set for flow control, but not priority flow control this brings pfc inline with fc. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NRoss Brattain <ross.b.brattain@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-