* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: blk_rq_err_sectors cleanup
  block: Honor the gfp_mask for alloc_page() in blkdev_issue_discard()
  block: Fix incorrect alignment offset reporting and update documentation
  cfq-iosched: don't regard requests with long distance as close
  aoe: switch to the new bio_flush_dcache_pages() interface
  drivers/block/mg_disk.c: use resource_size()
  drivers/block/DAC960.c: use DAC960_V2_Controller
  block: Fix topology stacking for data and discard alignment
  drbd: remove unused #include <linux/version.h>
  drbd: remove duplicated #include
  drbd: Fix test of unsigned in _drbd_fault_random()
  drbd: Constify struct file_operations
  cfq-iosched: Remove prio_change logic for workload selection
  cfq-iosched: Get rid of nr_groups
  cfq-iosched: Remove the check for same cfq group from allow_merge
  drbd: fix test of unsigned in _drbd_fault_random()
  block: remove Documentation/block/as-iosched.txt

dell-wmi: sys_init_module: 'dell_wmi'->init suspiciously returned 21, it should follow 0/-E convention

wmi_install_notify_handler() returns an acpi_error,
but dell_wmi_init() needs return a -errno style error.
Signed-off-by: NLen Brown <len.brown@intel.com>
Tested-by: NPaul Rolland <rol@as2917.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: rol@as2917.net <Paul Rolland>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: allow a resync that is waiting for other resync to complete, to be aborted.
  md: remove unnecessary code from do_md_run
  md: make recovery started by do_md_run() visible via sync_action
  md: fix small irregularity with start_ro module parameter
  md: Fix unfortunate interaction with evms

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (74 commits)
  Revert "b43: Enforce DMA descriptor memory constraints"
  iwmc3200wifi: fix array out-of-boundary access
  wl1251: timeout one too soon in wl1251_boot_run_firmware()
  mac80211: fix propagation of failed hardware reconfigurations
  mac80211: fix race with suspend and dynamic_ps_disable_work
  ath9k: fix missed error codes in the tx status check
  ath9k: wake hardware during AMPDU TX actions
  ath9k: wake hardware for interface IBSS/AP/Mesh removal
  ath9k: fix suspend by waking device prior to stop
  cfg80211: fix error path in cfg80211_wext_siwscan
  wl1271_cmd.c: cleanup char => u8
  iwlwifi: Storage class should be before const qualifier
  ath9k: Storage class should be before const qualifier
  cfg80211: fix race between deauth and assoc response
  wireless: remove remaining qual code
  rt2x00: Add USB ID for Linksys WUSB 600N rev 2.
  ath5k: fix SWI calibration interrupt storm
  mac80211: fix ibss join with fixed-bssid
  libertas: Remove carrier signaling from the scan code
  orinoco: fix GFP_KERNEL in orinoco_set_key with interrupts disabled
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  hwrng: core - Fix double unlock in rng_dev_read

generic_permission was refusing CAP_DAC_READ_SEARCH-enabled
processes from opening DAC-protected files read-only, because
do_filp_open adds MAY_OPEN to the open mask.

Ignore MAY_OPEN.  After this patch, CAP_DAC_READ_SEARCH is
again sufficient to open(fname, O_RDONLY) on a file to which
DAC otherwise refuses us read permission.
Reported-by: NMike Kazantsev <mk.fraggod@gmail.com>
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Tested-by: NMike Kazantsev <mk.fraggod@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The wrong address was being used to write the SCIR led regs on remote
hubs.  Also, there was an inconsistency between how BIOS and the kernel
indexed these regs.  Standardize on using the lower 6 bits of the APIC
ID as the index.

This patch fixes the problem of writing to an errant address to a
cpu # >= 64.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NJack Steiner <steiner@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move sys_mmap_pgoff() from mm/util.c to mm/mmap.c and mm/nommu.c,
where we'd expect to find such code: especially now that it contains
the MAP_HUGETLB handling.  Revert mm/util.c to how it was in 2.6.32.

This patch just ignores MAP_HUGETLB in the nommu case, as in 2.6.32,
whereas 2.6.33-rc2 reported -ENOSYS.  Perhaps validate_mmap_request()
should reject it with -EINVAL?  Add that later if necessary.
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit 45465487 ("kfifo: move struct
kfifo in place") caused a compile failure in ibmvscsitgt.c because it
changed a pointer to kfifo in the libsrp.h structure to a direct
inclusion without including <linux/kfifo.h>.

The fix is simple, just add the include, but how did this happen? This
change, introduced at -rc2, hardly looks like a bug fix, and it clearly
didn't go through linux-next, which would have picked up this compile
failure (it only occurs on ppc because of the ibm virtual scsi target).

[ Apparently all of -mm wasn't in linux-next.. ]
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

blk_rq_err_sectors() seems useless, get rid of it.
Signed-off-by: NGui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

If two arrays share a device, then they will not both resync at the
same time.  One will wait for the other to complete.
While waiting, the MD_RECOVERY_INTR flag is not checked so a device
failure, which would make the resync pointless, does not cause the
resync to abort, so the failed device cannot be removed (as it cannot
be remove while a resync is happening).

So add a test for MD_RECOVERY_INTR.
Reported-by: NBrett Russ <bruss@netezza.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Since commit dfc70645,
->hot_remove_disks has not removed non-failed devices from
an array until recovery is no longer possible.
So the code in do_md_run to get around the fact that
md_check_recovery (which calls ->hot_remove_disks) would
remove partially-in-sync devices is no longer needed.

So remove it.
Signed-off-by: NNeilBrown <neilb@suse.de>

By default md_do_sync() will perform recovery if no other actions are
specified.  However, action_show() relies on MD_RECOVERY_RECOVER to be
set otherwise it returns 'idle'.  So, add a missing set
MD_RECOVERY_RECOVER when starting recovery.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write.  This ensures that no resync/recovery happens until something
else writes to the device.  This is important for resume-from-disk
off an md array.

However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.

So strengthen the condition to only set auto-readonly if the
array is not already read-only.
Signed-off-by: NNeilBrown <neilb@suse.de>

evms configures md arrays by:
  open device
  send ioctl
  close device

for each different ioctl needed.
Since 2.6.29, the device can disappear after the 'close'
unless a significant configuration has happened to the device.
The change made by "SET_ARRAY_INFO" can too minor to stop the device
from disappearing, but important enough that losing the change is bad.

So: make sure SET_ARRAY_INFO sets mddev->ctime, and keep the device
active as long as ctime is non-zero (it gets zeroed with lots of other
things when the array is stopped).

This is suitable for -stable kernels since 2.6.29.
Signed-off-by: NNeilBrown <neilb@suse.de>
Cc: stable@kernel.org

This reverts commit 9bd568a5.

That commit is shown to cause allocation failures during initialization
on some machines.

http://bugzilla.kernel.org/show_bug.cgi?id=14844Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

queue_sector_alignment_offset returned the wrong value which caused
partitions to report an incorrect alignment_offset.  Since offset
alignment calculation is needed several places it has been split into a
separate helper function.  The topology stacking function has been
updated accordingly.

Furthermore, comments have been added to clarify how the stacking
function works.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Tested-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().

Cc: stable@kernel.org
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 does not propagate failed hardware reconfiguration
requests. For suspend and resume this is important due to all
the possible issues that can come out of the suspend <-> resume
cycle. Not propagating the error means cfg80211 will assume
the resume for the device went through fine and mac80211 will
continue on trying to poke at the hardware, enable timers,
queue work, and so on for a device which is completley
unfunctional.

The least we can do is to propagate device start issues and
warn when this occurs upon resume. A side effect of this patch
is we also now propagate the start errors upon harware
reconfigurations (non-suspend), but this should also be desirable
anyway, there is not point in continuing to reconfigure a
device if mac80211 was unable to start the device.

For further details refer to the thread:

http://marc.info/?t=126151038700001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.

Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.

The other mac80211 issue will be hanled in the next patch.

For further details see refer to the thread:

http://marc.info/?t=126144866100001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My previous change added in:

 commit 815833e7
    ath9k: fix tx status reporting

was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.

This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.

Cc: stable@kernel.org
Reported-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If there's an invalid channel or SSID, the code leaks
the scan request. Always free the scan request, unless
it was successfully given to the driver.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is just a clean up and doesn't make a functional difference.  It keeps the
lint checkers happy.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Joseph Nahmias reported, in http://bugs.debian.org/562016,
that he was getting the following warning (with some log
around the issue):

  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX AssocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated
  ------------[ cut here ]------------
  WARNING: at net/wireless/mlme.c:97 cfg80211_send_rx_assoc+0x14d/0x152 [cfg80211]()
  Hardware name: 7658CTO
  ...
  Pid: 761, comm: phy0 Not tainted 2.6.32-trunk-686 #1
  Call Trace:
   [<c1030a5d>] ? warn_slowpath_common+0x5e/0x8a
   [<c1030a93>] ? warn_slowpath_null+0xa/0xc
   [<f86cafc7>] ? cfg80211_send_rx_assoc+0x14d/0x152
  ...
  ath0: link becomes ready
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: no IPv6 routers present
  ath0: link is not ready
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX ReassocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated

It is not clear to me how the first "direct probe" here
happens, but this seems to be a race condition, if the
user requests to deauth after requesting assoc, but before
the assoc response is received. In that case, it may
happen that mac80211 tries to report the assoc success to
cfg80211, but gets blocked on the wdev lock that is held
because the user is requesting the deauth.

The result is that we run into a warning. This is mostly
harmless, but maybe cause an unexpected event to be sent
to userspace; we'd send an assoc success event although
userspace was no longer expecting that.

To fix this, remove the warning and check whether the
race happened and in that case abort processing.
Reported-by: NJoseph Nahmias <joe@nahmias.net>
Cc: stable@kernel.org
Cc: 562016-quiet@bugs.debian.org
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a rt2870 based device.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.

However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative.  As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.

Move the initialization order around so the calibration interval
is set before interrupts are active.  Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no reason to signal a carrier off when doing a 802.11 scan.

Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

orinoco_set_key is called from two places both with interrupts disabled
(under orinoco_lock). Use GFP_ATOMIC instead of GFP_KERNEL. Fixes following
warning:

[   77.254109] WARNING: at /home/bor/src/linux-git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x9a/0xa0()
[   77.254109] Hardware name: PORTEGE 4000
[   77.254109] Modules linked in: af_packet irnet ppp_generic slhc ircomm_tty ircomm binfmt_misc dm_mirror dm_region_hash dm_log dm_round_robin dm_multipath dm_mod loop nvram toshiba cryptomgr aead pcompress crypto_blkcipher michael_mic crypto_hash crypto_algapi orinoco_cs orinoco cfg80211 smsc_ircc2 pcmcia irda toshiba_acpi yenta_socket video i2c_ali1535 backlight rsrc_nonstatic ali_agp pcmcia_core psmouse output crc_ccitt i2c_core alim1535_wdt rfkill sg evdev ohci_hcd agpgart usbcore pata_ali libata reiserfs [last unloaded: scsi_wait_scan]
[   77.254109] Pid: 2296, comm: wpa_supplicant Not tainted 2.6.32-1avb #1
[   77.254109] Call Trace:
[   77.254109]  [<c011f0ad>] warn_slowpath_common+0x6d/0xa0
[   77.254109]  [<c014206a>] ? lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c014206a>] ? lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c011f0f5>] warn_slowpath_null+0x15/0x20
[   77.254109]  [<c014206a>] lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c018d296>] __kmalloc+0x36/0x130
[   77.254109]  [<dffcb6a8>] ? orinoco_set_key+0x48/0x1c0 [orinoco]
[   77.254109]  [<dffcb6a8>] orinoco_set_key+0x48/0x1c0 [orinoco]
[   77.254109]  [<dffcb9fc>] orinoco_ioctl_set_encodeext+0x1dc/0x2d0 [orinoco]
[   77.254109]  [<c035b117>] ioctl_standard_call+0x207/0x3b0
[   77.254109]  [<dffcb820>] ? orinoco_ioctl_set_encodeext+0x0/0x2d0 [orinoco]
[   77.254109]  [<c0307f1f>] ? rtnl_lock+0xf/0x20
[   77.254109]  [<c0307f1f>] ? rtnl_lock+0xf/0x20
[   77.254109]  [<c02fb115>] ? __dev_get_by_name+0x85/0xb0
[   77.254109]  [<c035b616>] wext_handle_ioctl+0x176/0x200
[   77.254109]  [<dffcb820>] ? orinoco_ioctl_set_encodeext+0x0/0x2d0 [orinoco]
[   77.254109]  [<c030020f>] dev_ioctl+0x6af/0x730
[   77.254109]  [<c02eec65>] ? move_addr_to_kernel+0x55/0x60
[   77.254109]  [<c02eed59>] ? sys_sendto+0xe9/0x130
[   77.254109]  [<c02ed77e>] sock_ioctl+0x7e/0x250
[   77.254109]  [<c02ed700>] ? sock_ioctl+0x0/0x250
[   77.254109]  [<c019cf4c>] vfs_ioctl+0x1c/0x70
[   77.254109]  [<c019d1fa>] do_vfs_ioctl+0x6a/0x590
[   77.254109]  [<c0178e50>] ? might_fault+0x90/0xa0
[   77.254109]  [<c0178e0a>] ? might_fault+0x4a/0xa0
[   77.254109]  [<c02ef90e>] ? sys_socketcall+0x17e/0x280
[   77.254109]  [<c019d759>] sys_ioctl+0x39/0x60
[   77.254109]  [<c0102e3b>] sysenter_do_call+0x12/0x32
[   77.254109] ---[ end trace 95ef563548d21efd ]---
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

seek_mean could be very big sometimes, using it as close criteria is meaningless
as this doen't improve any performance. So if it's big, let's fallback to
default value.
Reviewed-by: NCorrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>