This commit adds PCM functionality to transmit/receive PCM samples.

When one of PCM substreams are running or external clock source is
selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds streaming functionality for both direction. To utilize
the sequence of the number of data blocks in packets, full duplex with
synchronization is applied.

Besides, TASCAM FireWire series allows drivers to decide which PCM data
channels are enabled. For convenience, this driver always enable whole the
data channels.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

TASCAM FireWire series uses non-blocking transmission for AMDTP packet
streaming, while the format of data blocks is unique.

The CIP headers includes specific value in FMT field and no SYT
information.

In transmitted packets, the first data channel represents event counter,
and the last data channel has status and control information. The rest
has 24bit PCM samples with right padding.

In received packets, all of data channels include 16, 24, 32bit PCM
samples. There's no other kind of information.

This commit adds support for this protocol. For convenience, the size of
PCM samples in outgoing packet is limited by 16 and 24bit. The status and
control information will be supported in future commits.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

TASCAM FireWire series has certain registers for firmware information.

This commit adds proc node to show the information.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

TASCAM FireWire series doesn't tell drivers their capabilities, thus
the drivers should have model-dependent parameters and apply it to
detected devices.

This commit adds a structure to represent such parameters.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.

TASCAM FireWire series consists of:
 * PDI 1394P23 for IEEE 1394 PHY layer
 * PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
 * XILINX XC9536XL
 * XILINX Spartan-II XC2S100
 * ATMEL AT91M42800A

Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam

A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.

I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Digi 002/003 family uses asynchronous transaction for messaging.
The address to transmit this message is stored on a certain register.

This commit allocates a range of address on OHCI 1394 host controller
to handle the messaging. As long as I know, the purpose of this message
seems to notify lost of synchronization. While, the meaning of content
of the message is not clear.

Actual examples of this messaging:
 * When clock source is set as internal:
 - 0x00007051
 - 0x00007052
 - 0x00007054
 - 0x00007057
 - 0x00007058
 * When clock source is set as somewhat external:
 - 0x00009000
 - 0x00009010
 - 0x00009020
 - 0x00009021
 - 0x00009022

The lost often occurs when using internal clock source. In this case,
users hear sounds with quite short gap every several minutes. In fact,
the lost is recovered temporarily.

When using with external clock source, the lost seems not to occur. The
mechanism is not clear yet.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.

This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds PCM functionality to transmit/receive PCM samples.

Any PCM substreams are jointed because incoming/outgoing AMDTP streams
are bound. When one of PCM substream is running or external clock source
is selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds proc node to show current clock status for debugging.

As long as testing Digi 002 rack, registers can show local clock rate,
local clock source. When external clock input such as S/PDIF is
connected, the registers show the detection and external clock rate.

Additionally, the registers show the mode of optical digital input
interface. Although, a tester with Digi 003 rack reports this makes no
sense. Further investigation is required for Digi 003 series.

Besides, in Digi 002 rack, the S/PDIF format must be IEC 60958-4,
so-called professional.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a functionality to manage streaming.

The streaming is not controlled by CMP in IEC 61883-6. It's controlled by
IEEE 1394 write transaction to certain addresses.

Several clock sources are available, while there're no differences about
packet transmission. The value of SYT field in transmitted packets is
always zero. Thus, streams in both direction don't build synchronization.

And the device always requires received packets to transmit packets. This
driver keeps to transfer outgoing stream even if they're not required.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Digi 002/003 family uses its own format for data blocks. The format is
quite similar to AM824 in IEC 61883-6, while there're some differences:

 * The Valid Bit Length (VBL) code is always 0x40 in Multi-bit Linear Audio
   (MBLA) data channel.
 * The first data channel includes MIDI messages, against IEC 61883-6
   recommendation.
 * The Counter field is always zero in MIDI conformant data channel.
 * Sequence multiplexing in IEC 61883-6 is not applied to the MIDI
   conformant data channel.
 * PCM samples are scrambled in received AMDTP packets. We call the way
   as Double-Oh-Three (DOT). The algorithm was discovered by
   Robin Gareus and Damien Zammit in 2012.

This commit adds data processing layer to satisfy these differences.

There's a quirk about transmission mode for received packets. When this
driver applies non-blocking mode to outgoing packets with isochronous
channel 2 or more, after 15 to 20 seconds since playbacking, any PCM
samples causes noisy sound on the device. With isochronous channel 0 or 1,
this doesn't occur. As long as I investigated, this quirk is not observed
when applying blocking mode to the received packets.

This driver applies blocking mode to outgoing packets, while non-blocking
mode to incoming packgets.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a new driver for Digidesign 002/003 family. This commit
just creates/removes card instance according to bus event. More functions
will be added in following commits.

Digidesign 002/003 family consists of:
 * Agere FW802B for IEEE 1394 PHY layer
 * PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
 * ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller
 * ADSP-21065L for signal processing

[minor cleanup using skip_spaces() by tiwai]
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit moves the codes related to data block processing from packet
streaming layer to AM824 layer.

Each driver initializes amdtp stream structure for AM824 data block by
calling amdtp_am824_init(). Then, a memory block is allocated for AM824
specific structure. This memory block is released by calling
amdtp_stream_destroy().

When setting streaming parameters, it calls amdtp_am824_set_parameters().
When starting packet streaming, it calls amdtp_stream_start(). When
stopping packet streaming, it calls amdtp_stream_stop().
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit renames some macros just related to AM824 format. In later
commit, they're moved to AM824 layer.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Setting the format of PCM substream to AMDTP stream structure is important
to set a handler to copy actual PCM samples between buffers. The
processing should be in data block processing layer because essentially
it has no relationship to packet streaming.

This commit renames PCM format setting function to prepare for integrating
AM824 layer.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In IEC 61883-6, MIDI messages are transferred in MIDI conformant data
channel. Essentially, packet streaming layer is not responsible for MIDI
functionality.

This commit moves MIDI trigger helper function from the layer to AM824
layer. The rest of codes related to MIDI functionality will be moved in
later commits.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In IEC 61883-6, several types of data are available in AM824 format. The
data is transferred in each data channel. The position of data channel in
data block differs depending on model.

Current implementation has an array to map the index of data channel in an
data block to the position of actual data channel. The implementation
allows each driver to access the mapping directly.

In later commit, the mapping is in specific structure pushed into an
opaque pointer. Helper functions are required.

This commit adds the helper functions for this purpose. In IEC 61883-6,
AM824 format supports many data types, while this specification easily
causes over-engineering. Current AM824 implementation is allowed to handle
two types of data, Multi Bit Linear Audio data (=PCM samples) and MIDI
conformant data (=MIDI messages).
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In IEC 61883-6, PCM frames are transferred in Multi Bit Linear Audio data
channel. The data channel transfers 16/20/24 bit PCM samples. Thus, PCM
substream has a constrain about it.

This commit moves codes related to the constraint from packet streaming
layer to AM824 data block processing layer.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The value of FDF field in CIP header is protocol-dependent. Thus, it's
better to allow data block processing layer to decide the value in any
timing.

In AM824 data format, the value of FDF field in CIP header indicates
N-flag and Nominal Sampling Frequency Code (sfc). The N-flag is for
switching 'Clock-based rate control mode' and 'Command-based rate control
mode'. In our implementation, 'Clock-based rate control mode' is just
supported. Therefore, When sampling transfer frequency is decided, then
the FDF can be set.

This commit replaces 'amdtp_stream_set_parameters' with
'amdtp_am824_set_parameters' to set the FDF. This is the same timing
to decide the ration between the number of data blocks and the number of
PCM frames.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.

Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In later commit, data block processing layer will be newly added. This
layer will be named as 'amdtp-am824'.

This commit renames current amdtp file to amdtp-stream, to distinguish it
from the new layer.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some vendor specific protocol uses its own value for fmt/fdf fields in
CIP header.

This commit support to set arbitrary values for the fields.

In IEC 61883-6, NO-DATA code is defined for FDF field. A packet with this
code includes no data even if it includes some data blocks. This commit
still leaves a condition to handle this special packet.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALSA: firewire-lib: add helper functions as interfaces between packet streaming layer and data block processing layer

ALSA PCM framework uses PCM buffer with a concept of 'period' to
synchronize userspace operations to hardware for nearly-realtime
processing. Each driver implements snd_pcm_period_elapsed() to tell across
of the period boundary to ALSA PCM middleware. To call the function, some
drivers utilize hardware interrupt handlers, the others count handled PCM
frames.

Drivers for sound units on IEEE 1394 bus are the latter. They use two
buffers; PCM buffer and DMA buffer for IEEE 1394 isochronous packet. PCM
frames are copied between these two buffers and 'amdtp_stream' structure
counts the handled PCM frames. Then, snd_pcm_period_elapsed() is called if
required.

Essentially, packet streaming layer should not be responsible for PCM
frame processing. The PCM frame processing should be handled in each data
block processing layer as a result of handling data blocks. Although, PCM
frame counting is a common work for all of protocols which ALSA firewire
stack is going to support.

This commit adds two new helper functions as interfaces between packet
streaming layer to data block processing layer. In future, each data block
processing layer implements these functions. The packet streaming layer
calls data block processing layer per packet by calling the functions. The
data block processing layer processes data blocks and PCM frames, and
returns the number of processed PCM frames. Then the packet streaming layer
calculates handled PCM frames and calls snd_pcm_period_elapsed().
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In future commit, interface between data block processing layer and packet
stream processing layer is defined. These two layers communicate the
number of data blocks and the number of PCM frames.

The data block processing layer has a responsibility for calculating the
number of PCM frames. Therefore, 'dual wire' of Dice quirk should be
handled in data block processing layer.

This commit adds a member of 'frame_multiplier'. This member represents
the ratio of the number of PCM frames against the number of data blocks.
Usually, the value of this member is 1, while it's 2 in Dice's 'dual wire'.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In IEC 61883-6, one data block represents one event. In ALSA, the event is
one PCM frame. Therefore, when processing one data block, current
implementation counts one PCM frame.

On the other hand, Dice platform has a quirk called as 'dual wire' at
higher sampling rate. In detail, see comment of commit 6eb6c81e
("ALSA: dice: Split stream functionality into a file").

Currently, to handle this quirk, AMDTP stream structure has a
'double_pcm_frames' member. When this is enabled, two PCM frames are
counted. Each driver set this flag by accessing the structure member
directly.

In future commit, some members related to AM824 data block will be moved
to specific structure, to separate packet streaming layer and data block
processing layer. The access will be limited by opaque pointer.

For this reason, this commit adds an argument into
amdtp_stream_set_parameter() to set the flag.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently, amdtp_stream_set_parameters() returns no error even if wrong
arguments are given. This is not good for streaming layer because drivers
can continue processing ignoring capability of streaming layer.

This commit changes this function to return error code.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In later commit, some members related to AM824 data format will be moved
from AMDTP stream structure to data block structure. This commit is a
preparation for it. Additionally, current layout of AMDTP stream structure
is a bit mess by several extensions. This commit also arranges the layout.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Mackie Onyx Satellite has two usage; standalone and with base station.

These two modes has different stream formats. In standalone mode, rx data
block includes 2 Multi Bit Linear Audio (MBLA) data channels and tx data
block includes 2. With base station, they're 6 and 2.

Although, with base station, the actual tx packet include wrong value in
'dbs' field in its CIP header. This quirk causes packet streaming layer to
detect packet discontinuity and to stop PCM substream.

This is a response of 'single' subfunction 'extended stream format
information' command in AV/C Stream Format Information Specification 1.1.
It means that a data block in tx packets includes 2 MBLA data channels.

$ ./firewire-request /dev/fw1 fcp 0x01ffbfc001000000ffffffff
response: 000: 0c ff bf c0 01 00 00 00 ff 00 90 40 03 02 01 02
response: 010: 06

Current OXFW driver parses the response and detects stream formats
correctly.

$ cat /proc/asound/card1/firewire/formation
...
Output Stream from device:
	Rate	PCM	MIDI
* 	48000	2	0
 	44100	2	0
 	88200	2	0
	96000	2	0

On the other hand, in actual tx CIP, the 'dbs' field has 6. But the number
of quadlets in CIP payload is not multiple of 6. Seeing the subtraction of
two successive payload quadlets, it should be multiple of 2.

payload  CIP      CIP
quadlets header0  header1
      24 00060052 9002ffff
      24 0006005e 9002ffff
      26 0006006a 9002ffff
      24 00060077 9002ffff
      24 00060083 9002ffff
      26 0006008f 9002ffff
      24 0006009c 9002ffff
      24 000600a8 9002ffff
      26 000600b4 9002ffff
      24 000600c1 9002ffff

This commit adds support for this quirk to OXFW driver, by using
CIP_WRONG_DBS flag. When this flag is set, packet streaming layer uses
the value of its 'data_block_quadlets' member instead of the value in CIP
header. This value is already set by OXFW driver and no discontinuity is
detected.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In PCM core, when hw_params() in each driver returns error, the state of
PCM substream is kept as 'open'. In this case, current drivers for sound
units on IEEE 1394 bus doesn't decrement substream counter in hw_free()
correctly. This causes these drivers to keep streams even if not
required.

This commit fixes this bug. When snd_pcm_lib_alloc_vmalloc_buffer()
fails, hw_params function in each driver returns without incrementing the
counter.
Reported-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on from it.

Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.

As long as I investigated, AudioFire2/AudioFire4/AudioFirePre8 have a
quirk to transfer a first packet with 0x02 in its dbc field. This causes
ALSA Fireworks driver to detect discontinuity. In this case, firmware
version 5.7.0, 5.7.3 and 5.8.0 are used.

Payload  CIP      CIP
quadlets header1  header2
02       00050002 90ffffff <-
42       0005000a 90013000
42       00050012 90014400
42       0005001a 90015800
02       0005001a 90ffffff
42       00050022 90019000
42       0005002a 9001a400
42       00050032 9001b800
02       00050032 90ffffff
42       0005003a 9001d000
42       00050042 9001e400
42       0005004a 9001f800
02       0005004a 90ffffff
(AudioFire2 with firmware version 5.7.)

$ dmesg
snd-fireworks fw1.0: Detect discontinuity of CIP: 00 02

These models, AudioFire8 (since Jul 2009 ) and Gibson Robot Interface
Pack series uses the same ARM binary as their firmware. Thus, this
quirk may be observed among them.

This commit adds a new member for AMDTP structure. This member represents
the value of dbc field in a first AMDTP packet. Drivers can set it with
a preferred value according to model's quirk.
Tested-by: NJohannes Oertei <johannes.oertel@uni-due.de>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts commit 9c6893e0.

The fix is superseded by the next commit as a better implementation
for supporting AudioFire2/AudioFire4/AudioFirePre8 quirks.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on.

Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.

AudioFire2 has a quirk to transfer a first packet with non-zero in
its dbc field. This causes ALSA Fireworks driver to detect discontinuity.
As long as I investigated, firmware 5.7, 5.7.6 and 5.8 have this quirk.

This commit adds a support for the quirk to handle AudioFire2 packets.
For safe, CIP_SKIP_INIT_DBC_CHECK is applied to all versions of
AudioFire2's firmwares.

02 00050002 90ffffff <-
42 0005000a 90013000
42 00050012 90014400
42 0005001a 90015800
02 0005001a 90ffffff
42 00050022 90019000
42 0005002a 9001a400
42 00050032 9001b800
02 00050032 90ffffff
42 0005003a 9001d000
42 00050042 9001e400
42 0005004a 9001f800
02 0005004a 90ffffff
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

They're based on DM1500 (ArchWave produced), and BeBoB version 3 is
installed.

$ cat /proc/asound/FCA610/firewire/firmware
Manufacturer:	bridgeCo
Protocol Ver:	3
Build Ver:		0
GUID:		0x001564000002AD73
Model ID:		0x03
Model Rev:		0
Firmware Date:	20121102
Firmware Time:	153431
Firmware ID:	0x610
Firmware Ver:	8348
Base Addr:		0x400C0080
Max Size:		1422624
Loader Date:	20121015
Loader Time:	104710
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Behringer FCA610 transmits packets with periodic noisy PCM samples
when receiving no streams, and generates a bit noisy sound.

ALSA BeBoB driver is programmed to establish both in/out connections
when starting streaming, then transfers packets as userspace applications
requested. This means that there's a case that one of incoming/outgoing
streams is running, to save CPU and bandwidth usage. Although, it's natural
to start transferring packets in both direction.

This commit makes this driver to keeps duplex streams always.
Tested-by: NKim Tore Jensen <kim@incendio.no>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

PrismSound Orpheus, Behringer UFX1604 and FCA610 work with BeBoB v3, and
they're confirmed to transmit discontinuous packets in the beginning of
streaming.

payload    CIP headers
  8        0x00070000 0x9002FFFF
  8        0x00070000 0x9002FFFF
  8        0x00070000 0x9002FFFF
  8        0x00070008 0x9002FFFF <-
  8        0x00070008 0x9002FFFF
  8        0x00070008 0x9002FFFF
  8        0x00070008 0x9002FFFF
  8        0x00070008 0x9002FFFF
  8        0x00070008 0x9002FFFF
232        0x00070000 0x9002E798 <-
232        0x00070008 0x9002FB99
232        0x00070010 0x90021398
  8        0x00070018 0x9002FFFF
(This sample was got with Behringer FCA610 and FFADO library.)

This commit sets CIP_EMPTY_HAS_WRONG_DBC and CIP_SKIP_DBC_ZERO_CHECK to
ignore these discontinuities.
Tested-by: NKim Tore Jensen <kim@incendio.no>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Behringer FCA610 and UFX1604 is confirmed to require more time till
transmitting packets after establishing connections. This seems to
be a quirk of DM1500 ASIC which ArchWave produced.

For this quirk, this commit extends the time to wait up to 2 seconds.
As a result, in worst cases, below userspace functions require 2 seconds
to return.
 - snd_pcm_prepare()
 - snd_pcm_hw_params()
 - snd_pcm_recover()
Tested-by: NKim Tore Jensen <kim@incendio.no>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BeBoB installed devices have BeBoB register area. This area stores
basic information about its firmware. A register has its protocol
version.

This commit adds 'version' member and store the device's protocol
version to handle v3 quirks in following commits.
Tested-by: NKim Tore Jensen <kim@incendio.no>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>