The case where no vaid rate is found should not happen now
but to help debugging and downgrade this to a warn.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add omitted mutex_unlock to one of wl12xx_op_start fail paths (when
wl12xx_chip_wakeup fails).

[v2]
Power off the device, because:
\= cite from http://marc.info/?l=linux-kernel&m=124755028209880&w=2
If the chip cannot be booted, why should it remain powered on?
In some rare cases, the chip might fail to initialize, but can
recover if powered off and on again, so turning it off at this
point is the right thing to do. =/
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_dump_nic_error_log can be static and iwl_dump_nic_event_log
doesn't need to be exported.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding more detailed info about Asus motherboards and Ralink devices.
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New device supported by the zd1211rw driver reported to linux-wireless.
Device string from lsusb:
"ID 083a:e501 Accton Technology Corp. ZD1211B"

RF type from dmesg:
zd1211b chip 083a:e501 v4810 high 00-1a-2a AL2230_RF pa0 g--NS
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Adrián Cereto<ssorgatem@esdebian.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The work that we cancel there requires the cfg80211_mutex,
so we can't cancel it under the mutex, which is fine, we
can just move it to after the locked section.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In "mac80211: monitor the connection" I forgot to
add code to cancel the new timers & work when the
interface is brought down, which isn't a problem
if you just bring it down, but _is_ a problem when
you destroy the interface. Correct this lapse.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The result of container_of should not be NULL.  In particular, in this case
the argument to the enclosing function has passed though INIT_WORK, which
dereferences it, implying that its container cannot be NULL.

A simplified version of the semantic patch that makes this change is as
follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
identifier fn,work,x,fld;
type T;
expression E1,E2;
statement S;
@@

static fn(struct work_struct *work) {
  ... when != work = E1
  x = container_of(work,T,fld)
  ... when != x = E2
- if (x == NULL) S
  ...
}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211_set_wpa_version completely missed the use case when disabling
WPA, considering IW_AUTH_WPA_VERSION_DISABLED an invalid argument. This
caused weird error messages in wpa_supplicant.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DEVICE_STATE_DISABLED_RADIO_HW flag is only read but never set,
it is an ancient part of one of the many versions of the rfkill implementations
in rt2x00. It is about time is disappears.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch roughly implements xmit aggregation for ar9170-like device.
Not all AP are compatible with the driver(and firmware) yet, so YMMV.

A more refined code will definitely need the final HT specification
to be available for the public, lots of firmware modification and
possibly a redesigned driver just for good measure.
Sadly, these conditions won't come true anytime soon...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enhances the eeprom parser to generate customized
channel list for every device.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The "what-was-I-thinking-if-anything" patch. Clearly,
if cfg80211_send_disassoc() does wdev_lock() and then
calls __cfg80211_send_disassoc(), the latter shouldn't
lock again. And the sme_state test is ... no further
comments.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.

The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.
Signed-off-by: NStefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.

For example (from hwsim):

$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
	freq: 2462
	beacon interval: 100
	capability: ESS ShortSlotTime (0x0401)
	signal: -50.00 dBm
	SSID: j
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
	DS Paramater set: channel 11
	ERP: <no flags>
	Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pavel reported that you can't set the SSID from "foo" to
"bar". I tried reproducing, but used different values,
with different lengths, and thus never saw the obvious
problem.
Reported-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable is only used internally, _while_ connected.
If we use it, the sequence

# iwconfig wlan1 essid foo
<connects>
# iwconfig wlan1 essid ""
<disconnects>
# iwconfig

will still display "foo" as the SSID afterwards, which
is obviously quite bogus. Fix this by only displaying
the wext SSID, if present.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no reason to think that hwsim has any
actual signal strength, but for testing it is
very useful to have it report _some_ value to
the stack so I can see if the value ends up
being reported correctly
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of using the wext BSSID which may be NULL if
you haven't explicitly set one, we should instead use
the current_bss pointer -- if that's NULL we aren't
connected anyway. Fixes missing signal quality output
reported to me internally at Intel.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In cfg80211_scan_request n_channels refers to the total number
of channels to scan. Update the misleading comment accordingly.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1) there's a spin_lock() that needs to be spin_lock_bh()
2) action frames of size 24 might cause an out-of-bounds
   memory access (for the 25th byte only, so no big deal)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The cfg80211_sme_disassoc() function is already holding
a lock here that cfg80211_mlme_deauth() would take, so
it needs to use __cfg80211_mlme_deauth() instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the recent MLME rework I accidentally removed the connection
monitoring code. In order to add it back, this patch will add new
code to monitor both for beacon loss and for the connection actually
working, with possibly separate triggers.

When no unicast frames have been received from the AP for (currently)
two seconds, we will send the AP a probe request. Also, when we don't
see beacons from the AP for two seconds, we do the same (but those
times need not be the same due to the way the code is now written).

Additionally, clean up the parameters to the ieee80211_set_disassoc()
function that I need here, those are all useless except sdata.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have, sometimes, multiple things that want to
run but don't have their own timer. Introduce a
new function to mac80211's mlme run_again() that
makes sure that the timer will run again at the
_first_ needed time, use that function and also
properly reprogram the timer once it fired.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).

We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Rename maximum number of queue (TFD_QUEUE_MAX) to IWL39_NUM_QUEUES to
  be consistent with rest of iwlwifi.
* Remove unused defines.
* Fix loops that iterate over number of TX queues to stop when maximum is reached
  (currently it is maximum + 1).
* Remove queues_num module parameter as it is not used.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debugfs files are created with 644 permissions which gives everybody
read access. This presents a security issue if a user opens the file and
holds it open at the time the driver removes the file. At this point
invalid memory will be accessed.

Fix this by only allowing root to read debugfs files.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This move the show_qos file from sysfs to debugfs because the "one
value per file" sysfs rule.

The file is located in
/sys/kernel/debug/ieee80211/phy0/iwlagn/data
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch avoids memcpy from wdev->wext.ibss.bssid if it is NULL.
This could happen if we SIOCGIWAP before SIOCSIWAP.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Different revisions of WUSB54GC-EU use different chipsets -
v2 uses rtl8187, but v3 uses Ralink RT3070.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Przemyslaw Kulczycki <azrael@autocom.pl>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Linux wireless <linux-wireless@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.

In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.

Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assign next hop address to pending mesh frames once the path is resolved.

Regression.  Frames transmitted when a mesh path was wating to be resolved were
being transmitted with an invalid Receiver Address.

[Changes since v1]

Suggested by Johannes:
 - Improved frame_queue traversal
 - Narower RCU scope
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes two small bugs:
 1) the connect variable is already initialised, and the
    assignment to auth_type overwrites the previous setting
    with a wrong value
 2) when all authentication attempts fail, we need to report
    that we couldn't connect
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211_wext_giwrate doesn't lock the wdev, so it
cannot access current_bss race-free. Also, there's
little point in trying to ask the driver for an AP
that it never told us about, so avoid that case.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch re-enables p54's power save features and adds a workaround
which temporarily alters the device's power state in order to allow
ps-polls to be sent and buffered data to be retrieved during psm.

(Incorporates patch originally posted as "p54: fix beacon template dtim
IE corruption". -- JWL)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes mac80211 use the event tracing framework
to log all operations as given to the driver. This
will need to be extended with more information, but
as a start it should be good.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_testmode_cmd can very well be static.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/iwmc3200wifi/netdev.c
	net/wireless/scan.c