802.11 core interface is upgraded with 11ac support. Add channel spec support
code to brcmutil.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

enter/exit download state routine is going to diverge with new ARM core
introduced. Move corresponding code to sdio_chip.c for new ARM core support.
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For fullmac chips host driver can access to dongle RAM through SDIO function 1.
Introduce brcmf_sdio_ramrw and place it at bcmsdh.c with other interface
functions.
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Save & restore is an advanced power saving feature,
supported only on selected devices.
SR operation is almost completely transparent to the driver.
Support for it is hardware and firmware dependent.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is better to use kstrto* instead of simple_strtoul. In this case it
applies a bit stricter rules for input as well.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In routine _rtl8188e_read_power_value_fromprom(), there are loops initializing
index_cck_base and index_bw40_base from the PROM. As the result of a typo, the
second loop is ended one element too soon.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Inside one FIFO slot queue, EDMA chipsets have the same link pointer
re-read race condition as older chipsets, so the same buffer holding
logic needs to be used in order to avoid use-after-free bugs.
Unlike on older chips, it can be skipped for the end of the queue.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated
in the rx status word, but AR_RxFrameOK is also set, the descriptor
contents are typically invalid. This can show up as a warning about
invalid MCS rates in a frame. Even with those checks in place, a
descriptor with invalid MCS rates can still sometimes make it through to
the driver (mostly on older hardware like AR91xx).

Detect such errors in the last descriptor of a frame and discard the
whole frame if present.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As the comment in ath_get_next_rx_buf indicates, if a descriptor with
the done bit set follows one with the done bit cleared, both descriptors
should be discarded, however the driver is not doing that yet.

To fix this, use the rs->rs_more flag as an indicator that the following
frame should be discarded. This also helps with the split buffer case:
if the first part of the frame is discarded, the following parts need to
be discarded as well, since they contain no valid header or usable data.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is equivalent to ieee80211_hdrlen
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All users are converted to use the rt2x00mmio_*
functions so remove the now unused defines.

The patch contain no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions in the rt2x00mmio module has been
moved from the rt2x00pci module. Each function
uses the rt2x00pci prefix which is a bit confusing.
Use the r2x000mmio prefix for each function to make
it consistent with the module name.

The renamed functions are used by several modules,
and updating the names in all of them would result
in a big patch. In order to keep the patch simple,
add compatibility defines for the old function
names. This allows to update the names in each
module separately. After each module is updated,
the defines can be removed.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/ath/carl9170/debug.c
	drivers/net/wireless/ath/carl9170/main.c
	net/mac80211/ieee80211_i.h

Conflicts:
	drivers/net/wireless/rt2x00/rt2x00pci.c

In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could
change the ifidx using information in the event data. This is
only different to the BDC ifidx for IF ADD event. However, the
creation of the new interface is deferred to event worker so
it does not exist. After brcmf_fweh_process_skb() it is only
used to set statistics.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_p2p_notify_action_frame_rx() the wireless_dev
is needed to pass the action frame to cfg80211. The wireless_dev
is held in brcmf_cfg80211_vif object. Use that instead of the
ieee80211_ptr in net_device as P2P_DEVICE interface does not have
a net_device associated with it.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The probe requests received on P2P_DEVICE interface were not sent
to wpa_supplicant, which makes the device not discoverable by peers.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware console output can be read also when there was
no trap indication.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

reported by Hante. Needs to be squashed in commit 187fbcec.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not locking ra_list when dequeuing packets creates race conditions.
When adding a packet 'tx_pkts_queued' is modified before setting
highest_priority_queue. If in-between the main loop starts, it will
see a packet queued (tx_pkts_queued > 0) but will not find it, since
max prio is not set yet. Depending on the scheduling, the thread
trying to add the packet could complete and restore the situation.
But this is not something to rely on.

Another race condition exists, if a new packet, exceeding current
max prio is added. If concurrently a packet is dequeued, the newly
set max prio will be overwritten with the value of the dequeued
packet. This can occur, because selecting a packet and modifying
the max prio is not atomic. The result in an infinite loop unless,
a new packet is added that has at least the priority of the hidden
packet.

Same applies to bss_prio_tbl. Forward iteration is no proper
lock-free technique and provides no protection from calls to
list_del. Although BSS are currently not added/removed dynamically,
this must not be the case in the future. Hence always hold proper
locks when accessing those lists.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty
state, can lead to a contradictory state, resulting in an
infinite loop. Currently queueing and dequeuing of packets is
not synchronized, and can happen concurrently. While tx_pkts_queued
is incremented when adding a packet, max prio is set to NO_PKT when
the WMM list is empty. If a packet is added right after the check
for empty, but before setting max prio to NO_PKT, that packet is
trapped and creates an infinite loop.

Because of the new packet, tx_pkts_queued is at least 1, indicating
wmm lists are not empty. Opposing that max prio is NO_PKT, which
means "skip this wmm queue, it has no packets". The infinite loop
results, because the main loop checks the wmm lists for not empty
via tx_pkts_queued, but for dequeing it uses max_prio to see if it
can skip current list. This will never end, unless a new packet is
added which will restore max prio to the level of the trapped packet.

The solution here is to rely on tx_pkts_queued solely for checking
wmm queue to be empty, and drop the NO_PKT define. It does not
address the locking issue.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>