Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There's no space for the sign bit.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NVlad Yaseivch <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 8a83a00b.

It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.

Arnd can't remember exactly why he even needed this change.

Conflicts:

	drivers/net/macvlan.c
	net/8021q/vlan_dev.c
	net/core/dev.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neither compare_ether_addr() nor compare_ether_addr_64bits()
(as it can fall back to the former) have comparison semantics
like memcmp() where the sign of the return value indicates sort
order. We had a bug in the wireless code due to a blind memcmp
replacement because of this.

A cursory look suggests that the wireless bug was the only one
due to this semantic difference.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.

After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.

ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot)  If these resources are all ON,
then the state is D3hot.  If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.

This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The normal read_seqcount_begin() function will wait for any current
writers to exit their critical region by looping until the sequence
count is even.

That "wait for sequence count to stabilize" is the right thing to do if
the read-locker will just retry the whole operation on contention: no
point in doing a potentially expensive reader sequence if we know at the
beginning that we'll just end up re-doing it all.

HOWEVER.  Some users don't actually retry the operation, but instead
will abort and do the operation with proper locking.  So the sequence
count case may be the optimistic quick case, but in the presense of
writers you may want to do full locking in order to guarantee forward
progress.  The prime example of this would be the RCU name lookup.

And in that case, you may well be better off without the "retry early",
and are in a rush to instead get to the failure handling.  Thus this
"raw" interface that just returns the sequence number without testing it
- it just forces the low bit to zero so that read_seqcount_retry() will
always fail such a "active concurrent writer" scenario.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it.  As a
result, it might end up returning an odd value (which means that a write
is in progress).

If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.

In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.

So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload.  But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug.  Let's just make sure.

Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Devices with many DAIs are becoming more and more common, and generally
the more modern devices have consistent register layouts between DAIs.
Rather than have drivers open code lookups based on the DAI ID or cause
uglification in UI by having register addresses for IDs provide a base
address field they can use.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

fix kernel doc typos in function names
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NGeorgi Vlaev <joe@nucleusys.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

More recent versions of the UEFI spec have added new attributes for
variables. Add them.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

<asm-generic/statfs.h> is exported to userspace, so using
BITS_PER_LONG is invalid.  We need to use __BITS_PER_LONG instead.

This is kernel bugzilla 43165.
Reported-by: NH.J. Lu <hjl.tools@gmail.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1335465916-16965-1-git-send-email-hpa@linux.intel.comAcked-by: NArnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>

Denys Fedoryshchenko reported frequent crashes on a proxy server and kindly
provided a lockdep report that explains it all :

  [  762.903868]
  [  762.903880] =================================
  [  762.903890] [ INFO: inconsistent lock state ]
  [  762.903903] 3.3.4-build-0061 #8 Not tainted
  [  762.904133] ---------------------------------
  [  762.904344] inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
  [  762.904542] squid/1603 [HC0[0]:SC0[0]:HE1:SE1] takes:
  [  762.904542]  (key#3){+.?...}, at: [<c0232cc4>]
__percpu_counter_sum+0xd/0x58
  [  762.904542] {IN-SOFTIRQ-W} state was registered at:
  [  762.904542]   [<c0158b84>] __lock_acquire+0x284/0xc26
  [  762.904542]   [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]   [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]   [<c0232c93>] __percpu_counter_add+0x58/0x7c
  [  762.904542]   [<c02cfde1>] sk_clone_lock+0x1e5/0x200
  [  762.904542]   [<c0303ee4>] inet_csk_clone_lock+0xe/0x78
  [  762.904542]   [<c0315778>] tcp_create_openreq_child+0x1b/0x404
  [  762.904542]   [<c031339c>] tcp_v4_syn_recv_sock+0x32/0x1c1
  [  762.904542]   [<c031615a>] tcp_check_req+0x1fd/0x2d7
  [  762.904542]   [<c0313f77>] tcp_v4_do_rcv+0xab/0x194
  [  762.904542]   [<c03153bb>] tcp_v4_rcv+0x3b3/0x5cc
  [  762.904542]   [<c02fc0c4>] ip_local_deliver_finish+0x13a/0x1e9
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc652>] ip_local_deliver+0x41/0x45
  [  762.904542]   [<c02fc4d1>] ip_rcv_finish+0x31a/0x33c
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc857>] ip_rcv+0x201/0x23e
  [  762.904542]   [<c02daa3a>] __netif_receive_skb+0x319/0x368
  [  762.904542]   [<c02dac07>] netif_receive_skb+0x4e/0x7d
  [  762.904542]   [<c02dacf6>] napi_skb_finish+0x1e/0x34
  [  762.904542]   [<c02db122>] napi_gro_receive+0x20/0x24
  [  762.904542]   [<f85d1743>] e1000_receive_skb+0x3f/0x45 [e1000e]
  [  762.904542]   [<f85d3464>] e1000_clean_rx_irq+0x1f9/0x284 [e1000e]
  [  762.904542]   [<f85d3926>] e1000_clean+0x62/0x1f4 [e1000e]
  [  762.904542]   [<c02db228>] net_rx_action+0x90/0x160
  [  762.904542]   [<c012a445>] __do_softirq+0x7b/0x118
  [  762.904542] irq event stamp: 156915469
  [  762.904542] hardirqs last  enabled at (156915469): [<c019b4f4>]
__slab_alloc.clone.58.clone.63+0xc4/0x2de
  [  762.904542] hardirqs last disabled at (156915468): [<c019b452>]
__slab_alloc.clone.58.clone.63+0x22/0x2de
  [  762.904542] softirqs last  enabled at (156915466): [<c02ce677>]
lock_sock_nested+0x64/0x6c
  [  762.904542] softirqs last disabled at (156915464): [<c0349914>]
_raw_spin_lock_bh+0xe/0x45
  [  762.904542]
  [  762.904542] other info that might help us debug this:
  [  762.904542]  Possible unsafe locking scenario:
  [  762.904542]
  [  762.904542]        CPU0
  [  762.904542]        ----
  [  762.904542]   lock(key#3);
  [  762.904542]   <Interrupt>
  [  762.904542]     lock(key#3);
  [  762.904542]
  [  762.904542]  *** DEADLOCK ***
  [  762.904542]
  [  762.904542] 1 lock held by squid/1603:
  [  762.904542]  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<c03055c0>]
lock_sock+0xa/0xc
  [  762.904542]
  [  762.904542] stack backtrace:
  [  762.904542] Pid: 1603, comm: squid Not tainted 3.3.4-build-0061 #8
  [  762.904542] Call Trace:
  [  762.904542]  [<c0347b73>] ? printk+0x18/0x1d
  [  762.904542]  [<c015873a>] valid_state+0x1f6/0x201
  [  762.904542]  [<c0158816>] mark_lock+0xd1/0x1bb
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c015805d>] ? check_usage_forwards+0x77/0x77
  [  762.904542]  [<c0158bf8>] __lock_acquire+0x2f8/0xc26
  [  762.904542]  [<c0159b8e>] ? mark_held_locks+0x5d/0x7b
  [  762.904542]  [<c0159cf6>] ? trace_hardirqs_on+0xb/0xd
  [  762.904542]  [<c0158dd4>] ? __lock_acquire+0x4d4/0xc26
  [  762.904542]  [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0232cc4>] __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c02cebc4>] __sk_mem_schedule+0xdd/0x1c7
  [  762.904542]  [<c02d178d>] ? __alloc_skb+0x76/0x100
  [  762.904542]  [<c0305e8e>] sk_wmem_schedule+0x21/0x2d
  [  762.904542]  [<c0306370>] sk_stream_alloc_skb+0x42/0xaa
  [  762.904542]  [<c0306567>] tcp_sendmsg+0x18f/0x68b
  [  762.904542]  [<c031f3dc>] ? ip_fast_csum+0x30/0x30
  [  762.904542]  [<c0320193>] inet_sendmsg+0x53/0x5a
  [  762.904542]  [<c02cb633>] sock_aio_write+0xd2/0xda
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c01a1017>] do_sync_write+0x9f/0xd9
  [  762.904542]  [<c01a2111>] ? file_free_rcu+0x2f/0x2f
  [  762.904542]  [<c01a17a1>] vfs_write+0x8f/0xab
  [  762.904542]  [<c01a284d>] ? fget_light+0x75/0x7c
  [  762.904542]  [<c01a1900>] sys_write+0x3d/0x5e
  [  762.904542]  [<c0349ec9>] syscall_call+0x7/0xb
  [  762.904542]  [<c0340000>] ? rp_sidt+0x41/0x83

Bug is that sk_sockets_allocated_read_positive() calls
percpu_counter_sum_positive() without BH being disabled.

This bug was added in commit 180d8cd9
(foundations of per-cgroup memory pressure controlling.), since previous
code was using percpu_counter_read_positive() which is IRQ safe.

In __sk_mem_schedule() we dont need the precise count of allocated
sockets and can revert to previous behavior.
Reported-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Sined-off-by: NEric Dumazet <edumazet@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change order of init so netns init is ready
when register ioctl and netlink.

Ver2
	Whitespace fixes and __init added.
Reported-by: N"Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: NHans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.
Signed-off-by: NHans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSimon Horman <horms@verge.net.au>

The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.

When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own.  The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).

End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time.  You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.

NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops.  Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.

The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes).  But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: NMichael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org  # needed for systemd/autofs interaction fix
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warning in spi.h (copy/paste):

Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.

Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>

Some on SoC DSP HW is very tightly coupled with DMA and DAI drivers. It's
necessary to allow some flexability wrt to PCM operations here so that we
can define a bespoke DPCM trigger() PCM operation for such HW.

A bespoke DPCM trigger() allows exact ordering and timing of component
triggering by allowing a component driver to manage the final enable
and disable configurations without adding extra complexity to other
component drivers. e.g. The McPDM DAI and ABE are tightly coupled on
OMAP4 so we have a bespoke trigger to manage the trigger to improve
performance and reduce complexity when triggering new McPDM BEs.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some component drivers will need to be able to look up their
DAI link substream and RTD data. Provide a mechanism for this.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows DPCM to dynamically alter the FE to BE PCM links
at runtime based on mixer setting updates. DAPM is looked up after
every mixer update and we perform a DPCM runtime update if the
mixer has a change of value.

This patchs adds/changes the following :-

 o Adds DPCM runtime update core.
 o Changes soc_dapm_mixer_update_power() and soc_dapm_mux_update_power()
   to return if a change has occured rather than 0. No other users check
   atm.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add debugFS files for DPCM link management information.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The Dynamic PCM core allows digital audio data to be dynamically
routed between different ALSA PCMs and DAI links on SoC CPUs with
on chip DSP devices. e.g. audio data could be played on pcm:0,0 and
routed to any (or all) SoC DAI links.

Dynamic PCM introduces the concept of Front End (FE) PCMs and Back
End (BE) PCMs. The FE PCMs are normal ALSA PCM devices except that
they can dynamically route digital audio data to any supported BE
PCM. A BE PCM has no ALSA device, but represents a DAI link and it's
substream and audio HW parameters.

e.g. pcm:0,0 routing digital data to 2 external codecs.

FE pcm:0,0  ----> BE (McBSP.0) ----> CODEC 0
             +--> BE (McPDM.0) ----> CODEC 1

e.g. pcm:0,0 and pcm:0,1 routing digital data to 1 external codec.

FE pcm:0,0 ---
             +--> BE (McBSP.0) ----> CODEC
FE pcm:0,1 ---

The digital audio routing is controlled by the usual ALSA method
of mixer kcontrols. Dynamic PCM uses a DAPM graph to work out the
routing based upon the mixer settings and configures the BE PCMs
based on routing and the FE HW params.

DPCM is designed so that most ASoC component drivers will need no
modification at all. It's intended that existing CODEC, DAI and
platform drivers can be used in DPCM based audio devices without
any changes. However, there will be some cases where minor changes
are required (e.g. for very tightly coupled HW) and there are
helpers to support this too.

Somethimes the HW params of a FE and BE do not match or are
incompatible, so in these cases the machine driver can reconfigure
any hw_params and make any DSP perform sample rate / format conversion.

This patch adds the core DPCM code and contains :-

 o The FE and BE PCM operations.
 o FE and BE DAI link support.
 o FE and BE PCM creation.
 o BE support API.
 o BE and FE link management.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The "pgsteal" stat is confusing because it counts both direct reclaim as
well as background reclaim.  However, we have "kswapd_steal" which also
counts background reclaim value.

This patch fixes it and also makes it match the existng "pgscan_" stats.

Test:
pgsteal_kswapd_dma32 447623
pgsteal_kswapd_normal 42272677
pgsteal_kswapd_movable 0
pgsteal_direct_dma32 2801
pgsteal_direct_normal 44353270
pgsteal_direct_movable 0
Signed-off-by: NYing Han <yinghan@google.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: NMinchan Kim <minchan@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Tested-by: NOleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: set fake_rtable's dst to NULL to avoid kernel Oops

when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.

v4 reformat, change br_drop_fake_rtable(skb) to {}

v3 enrich commit header

v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.

[ Use "do { } while (0)" for nop br_drop_fake_rtable()
  implementation -DaveM ]
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPeter Huang <peter.huangpeng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the particular issue of x32, which shares code with i386 in the
handling of compat_siginfo_t, the use of a 64-bit clock_t bumps the
sigchld structure out of alignment, which triggers a messy cascade of
padding.

This was already handled on the kernel compat side, but it needs
handling on the user space side, which uses the generic header.  To
make that possible:

1. Allow __kernel_clock_t to be overridden in struct siginfo;
2. Allow there to be attributes added to struct siginfo.
Reported-by: NH.J. Lu <hjl.rools@gmail.com>
Cc: Bruce J. Beare <bruce.j.beare@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/CAMe9rOqF6Kh6-NK7oP0Fpzkd4SBAWU%2BG53hwBbSD4iA2UzyxuA@mail.gmail.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Added support for a control that strobes a bit in
a register to high then back to low (or the inverse).

This is typically useful for hardware that requires
strobing a singe bit to trigger some functionality
and where exposing the bit in a normal single control
would require the user to first manually set then
again unset the bit again for the strobe to trigger.

Added convenience macro.

SOC_SINGLE_STROBE

Added accessor implementations.

snd_soc_get_strobe
snd_soc_put_strobe
Signed-off-by: NKristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Added control type that can span multiple consecutive codec registers
forming a single signed value in a MSB/LSB manner.
The control dynamically adjusts to the register word size configured
in driver.

Added convenience macro.

SOC_SINGLE_XR_SX

Added accessor implementations.

snd_soc_info_xr_sx
snd_soc_get_xr_sx
snd_soc_put_xr_sx
Signed-off-by: NKristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fixes the following build warning on x86_64.

In file included from include/trace/ftrace.h:567:0,
                 from include/trace/define_trace.h:86,
                 from include/trace/events/asoc.h:410,
                 from sound/soc/soc-core.c:45:
include/trace/events/asoc.h: In function 'ftrace_raw_event_snd_soc_dapm_output_path':
include/trace/events/asoc.h:246:1: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
include/trace/events/asoc.h: In function 'ftrace_raw_event_snd_soc_dapm_input_path':
include/trace/events/asoc.h:275:1: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove custom hack and make use of the notifier chain interfaces for
delivering events from the ports to their associated clients.
Clients that want to receive port events need to register their callbacks
using hsi_register_port_event(). The callbacks can be called in interrupt
context. Use hsi_unregestier_port_event() to undo the registration.
Signed-off-by: NCarlos Chinea <carlos.chinea@nokia.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Use the proper release mechanism for hsi_controller and
hsi_ports structures. Free the structures through their
associated device release callbacks.
Signed-off-by: NCarlos Chinea <carlos.chinea@nokia.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

This changes the ordering of initialization and probing events from:
  1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
  1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  3/ schedule port probe in DISCE_PROBE

This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:

  BUG: unable to handle kernel paging request at 0000000000003b10
  IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
  ...
  [<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
  [<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
  [<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
  [<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
  [<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]

...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: NMichal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry.  Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.

Fixes reports like:
  BUG: unable to handle kernel NULL pointer dereference at           (null)
  IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).

The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

it's always current->mm
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The NFSv4 spec is ambiguous about whether or not it is permissible
to reuse open owner names, so play it safe. This patch adds a timestamp
to the state_owner structure, and combines that with the IDA based
uniquifier.
Fixes a regression whereby the Linux server returns NFS4ERR_BAD_SEQID.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.

Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.htmlSigned-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.

This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c.  But that way we don't have
to export our internal do_mmap_pgoff() function.

Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead.  We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>