The workaround itself applies to gen7 only (according to the docs) and
as Eric Anholt points out shouldn't be required since we don't use HW
scheduling features, and therefore arbitration. Though since it is a
small, and simple addition, and we don't really understand the issue,
just do it.

FWIW, I eventually want to play with some of the arbitration stuff, and
I'd hate to forget about this.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>

This way round we don't introduce and ugly layering violations and use
the interface as I planned to use it.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Implement the context switch code as well as the interfaces to do the
context switch. This patch also doesn't match 1:1 with the RFC patches.
The main difference is that from Daniel's responses the last context
object is now stored instead of the last context. This aids in allows us
to free the context data structure, and context object independently.

There is room for optimization: this code will pin the context object
until the next context is active. The optimal way to do it is to
actually pin the object, move it to the active list, do the context
switch, and then unpin it. This allows the eviction code to actually
evict the context object if needed.

The context switch code is missing workarounds, they will be implemented
in future patches.

v2: actually do obj->dirty=1 in switch (daniel)
Modified comment around above
Remove flags to context switch (daniel)
Move mi_set_context code to i915_gem_context.c (daniel)
Remove seqno , use lazy request instead (daniel)

v3: use i915_gem_request_next_seqno instead of
      outstanding_lazy_request (Daniel)
remove id's from trace events (Daniel)
Put the context BO in the instruction domain (Daniel)
Don't unref the BO is context switch fails (Chris)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>

Invent an abstraction for a hw context which is passed around through
the core functions. The main bit a hw context holds is the buffer object
which backs the context. The rest of the members are just helper
functions. Specifically the ring member, which could likely go away if
we decide to never implement whatever other hw context support exists.

Of note here is the introduction of the 64k alignment constraint for the
BO. If contexts become heavily used, we should consider tweaking this
down to 4k. Until the contexts are merged and tested a bit though, I
think 64k is a nice start (based on docs).

Since we don't yet switch contexts, there is really not much complexity
here. Creation/destruction works pretty much as one would expect. An idr
is used to generate the context id numbers which are unique per file
descriptor.

v2: add DRM_DEBUG_DRIVERS to distinguish ENOMEM failures (ben)
convert a BUG_ON to WARN_ON, default destruction is still fatal (ben)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>

Very basic code for context setup/destruction in the driver.

Adds the file i915_gem_context.c This file implements HW context
support. On gen5+ a HW context consists of an opaque GPU object which is
referenced at times of context saves and restores.  With RC6 enabled,
the context is also referenced as the GPU enters and exists from RC6
(GPU has it's own internal power context, except on gen5).  Though
something like a context does exist for the media ring, the code only
supports contexts for the render ring.

In software, there is a distinction between contexts created by the
user, and the default HW context. The default HW context is used by GPU
clients that do not request setup of their own hardware context. The
default context's state is never restored to help prevent programming
errors. This would happen if a client ran and piggy-backed off another
clients GPU state.  The default context only exists to give the GPU some
offset to load as the current to invoke a save of the context we
actually care about. In fact, the code could likely be constructed,
albeit in a more complicated fashion, to never use the default context,
though that limits the driver's ability to swap out, and/or destroy
other contexts.

All other contexts are created as a request by the GPU client. These
contexts store GPU state, and thus allow GPU clients to not re-emit
state (and potentially query certain state) at any time. The kernel
driver makes certain that the appropriate commands are inserted.

There are 4 entry points into the contexts, init, fini, open, close.
The names are self-explanatory except that init can be called during
reset, and also during pm thaw/resume. As we expect our context to be
preserved across these events, we do not reinitialize in this case.

As Adam Jackson pointed out, The cutoff of 1MB where a HW context is
considered too big is arbitrary. The reason for this is even though
context sizes are increasing with every generation, they have yet to
eclipse even 32k. If we somehow read back way more than that, it
probably means BIOS has done something strange, or we're running on a
platform that wasn't designed for this.

v2: rename load/unload to init/fini (daniel)
remove ILK support for get_size() (indirectly daniel)
add HAS_HW_CONTEXTS macro to clarify supported platforms (daniel)
added comments (Ben)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>

The GPUs can have different default context layouts, and the sizes could
vary based on platform or BIOS. In order to back the context object with
a properly sized BO, we must read this register in order to find out a
sufficient size.

Thankfully (sarcarm!), the register moves and changes meanings
throughout generations.

CTX and CXT differences are intentional as that is how it is in the
documentation (prior to GEN6 it was CXT).
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>

The Lenovo Thinkpad T410 has the LVDS_PIPEB_SELECT bit set in the LVDS
register when booted with the lid closed, even though the LVDS hasn't
really been initialized. Ignore this bit so that the VBT value will be
used instead.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we switch on/off the primary plane if it is completely obscured by an
overlapping video sprite, we also nee to make sure that we update the
FBC configuration at the same time.

v2: Not all crtcs are intel_crtcs, as spotted by Daniel.
v3: Boot testing rules.

References: https://bugs.freedesktop.org/show_bug.cgi?id=50238Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.

Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.

Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...

v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling

v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.

v4: Jani Nikula complained about the pointless bool primary
initialization.

v5: Don't oops if we can't allocate, noticed by Chris Wilson.

v6: Resolve conflicts with agp rework and fixup whitespace.
Reported-and-tested-by: N"Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When drm/i915 is in control of the gtt, we need to call
the enable function at all the relevant places ourselves.
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this thing much earlier, and it doesn't make sense
in the hw enabling function intel_enable_gtt - this does not
change over a suspend/resume cycle ...
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To be able to directly set up the intel-gtt code from drm/i915 and
avoid setting up the fake-agp driver we need to prepare a few things:
- pass both the bridge and gpu pci_dev to the probe function and add
  code to handle the gpu pdev both being present (for drm/i915) and
  not present (fake agp).
- add refcounting to the remove function so that unloading drm/i915
  doesn't kill the fake agp driver

v2: Fix up the cleanup and refcount, noticed by Jani Nikula.
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only need it to fake the agp interface and don't actually
use it in the driver anywhere. Hence conditionalize that.

This is just a prep patch to eventually disable the fake agp
driver on gen6+.
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For that to work we need to export the base address of the gtt
mmio window from intel-gtt. Also replace all other uses of
dev->agp by values we already have at hand.
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a leftover from the conversion of the i81x fake agp driver
over to the new intel-gtt code layoute.
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Given the havoc the missing backlight pipe select code might have
caused, let's try to re-enabled pipe A support for lvds on gen4 hw.
Just to see what all blows up ...

Note though that

commit 4add75c4
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Sat Dec 4 17:49:46 2010 +0000

    drm/i915: Allow LVDS to be on pipe A for Ironlake+

claims that this caused tons of spurious wakeups somehow.

More details can be found in the old revert:

commit 12e8ba25
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Sep 7 23:39:28 2010 +0100

    Revert "drm/i915: Allow LVDS on pipe A on gen4+"

    Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On gen4+ we have a bitfield to specify from which pipe the backlight
controller should take it's clock. For PCH split platforms we've
already set these up, but only at initialization time. And without
taking into account the 3rd pipe added with ivb.

For gen4, we've completely ignored these. Although we do restrict lvds
to the 2nd pipe, so this is only a problem on machines where we boot
up with the lvds on the first pipe.

So restructure the code to enable the backlight on the right pipe at
modeset time.

v2: For odd reasons panel_enable_backlight gets called twice in a
modeset, so we can't WARN_ON in there if the backlight controller is
switched on already.

v3: backlight enable can also be called through dpms on, so the check
in there is legit. Update the comment to reflect that.
Tested-By: NKamal Mostafa <kamal@canonical.com>
Bugzilla: https://bugs.launchpad.net/bugs/954661
Cc: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Regroup definitions for BLC_PWM_CTL so that they're all together and
  and ordered according to the bitfields.

- Add all missing definitions for BLC_PWM_CTL2.

- Use the BLM_ (for backlight modulation) prefix consistently.

- Note that combination mode (i.e. also taking the legacy backlight
  control value from pci config space into account) is gen4 only.

- Move the new registers for PCH-split machines up, they're an almost
  match for the gen4 defitions.  Prefix the special PCH-only bits with
  BLM_PCH_. Also add the pipe C select bit for ivb.

- Rip out the second pair of PCH polarity definitions - they're only
  valid on early (pre-production) ilk silicon.

- Adapt the existing code to use the new definitions. This has the
  nice benefit of killing a magic (1 << 30) left behind be Jesse
  Barnes.

No functional changes in this patch.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already correctly ignore bit0 on gen < 4, now we also know why ;-)
I've decided that losing that single bit of precision isn't worth the
trouble to sprinkle IS_PINEVIEW checks all over the backlight control
code - that code is way too fragile imo.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is supposed to be used at mode set time, so prevent
against future mistakes by adding a WARN().

Based on a patch by Paulo Zanoni, with the check extracted into a
little assert_hdmi_port_disabled helper added to make things self
documenting and move the assert stuff out of line.

[fixed up spelling goof-up while applying.]
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Change the ns_timeout parameter of the wait ioctl to a signed value.
Doing this allows the kernel to provide an infinite wait when a timeout
of less than 0 is provided. This mimics select/poll.

Initially the parameter was meant to match up with the GL spec 1:1, but
after being made aware of how much 2^64 - 1 nanoseconds actually is, I
do not think anyone will ever notice the loss of 1 bit.

The infinite timeout on waiting is similar to the existing i915
userspace interface with the exception that struct_mutex is dropped
while doing the wait in this ioctl.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's be a bit more paranoid here.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec Vol 3, Part 3, Section 3.8.1.1, bit 30:

"[DevIBX] Writing to this bit only takes effect when port is enabled.
Due to hardware issue it is required that this bit be cleared when port
is disabled. To clear this bit software must temporarily enable this
port on transcoder A."

Unfortunately the public Bspec misses totally out on the same language
for HDMIB. Internal Bspec also mentions that one of the bad
side-effects is that DPx can fail to light up on transcoder A if HDMIx
is disabled but using transcoder B.

I've found this while reviewing Bsepc. We already implement the same
workaround for the DP ports.

Also replace a magic 1 with PIPE_B I've found while looking through the
code.

v2: Implement suggestions from Chris Wilson:
- add pipe variable to cut down on code noise
- write the reg value twice to w/a hw issues (Bspec is unclear on
  which bit actually require the write twice stuff, but better be
  paranoid about it)
- untangle the if logic
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes for easier benchmarking and testing.  One can set a fixed
frequency by setting min and max to the same value.

v2: fix whitespace & comment (Eugeni)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NEugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.

After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.

Also mark the mode argument of pch_panel_fitting const.

v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of changing mode->clock, which we should leave as-is.

After the previous patch we only touch that if it's a panel, and then
adjusted mode->clock equals adjusted_mode->clock. Outside of
intel_dp.c we only use ajusted_mode->clock in the mode_set functions.

Within intel_dp.c we only use it to calculate the dp dithering
and link bw parameters, so that's the only thing we need to fix
up.

As a temporary ugliness (until the cleanup in the next patch) we
pass the adjusted_mode into dp_dither for both parameters (because
that one still looks at mode->clock).

Note that we do overwrite adjusted_mode->clock with the selected dp
link clock, but that only happens after we've calculated everything we
need based on the dotclock of the adjusted output configuration.

Outside of intel_dp.c only intel_display.c uses adjusted_mode->clock,
and that stays the same after this patch (still equals the selected dp
link clock). intel_display.c also needs the actual dotclock (as
target_clock), but that has been fixed up in the previous patch.

v2: Adjust the debug message to also use adjusted_mode->clock.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.

The next patch will stop us from modifying mode->clock.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both busy_ioctl and the new wait_ioct need to do the same dance (or at
least should). Some slight changes:
- busy_ioctl now unconditionally checks for olr. Before emitting a
  require flush would have prevent the olr check and hence required a
  second call to the busy ioctl to really emit the request.
- the timeout wait now also retires request. Not really required for
  abi-reasons, but makes a notch more sense imo.

I've tested this by pimping the i-g-t test some more and also checking
the polling behviour of the wait_rendering_timeout ioctl versus what
busy_ioctl returns.

v2: Too many people complained about unplug, new color is
flush_active.

v3: Kill the comment about the unplug moniker.

v4: s/un-active/inactive/
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of checking for !CPT, check for IBX to make it clearer that
this is a IBX-specific workaround. No functional change because we
smash the PPT PCH into the HAS_PCH_CPT check and atm DP isn't enabled
on the haswell LPT PCH yet.

See Bspec Vol 3, Part 3, Section 4.[3-5].1 about DP[BCD], bit 30 for
details of this workaround.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Positively checking for the required feature/gen is simpler than build
a cascade of negative "we need to bail" checks. And the later won't
scale if we add more stuff that doesn't fit in nicely.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
  work item that should be on it's runlist.

Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Notice by Fengguang Wu's automatic sparse checker.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is the same as the nouveau code pretty much.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Tested sharing to udl.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This allows udl to get a vmapping of an imported buffer for scanout.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is used to export a vmapping to the udl driver so that
i915 and udl can share the udl scanout.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds a stub until we have pieces in place to test
a correct one.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds a stub until we have some users in place to test
this with.
Signed-off-by: NDave Airlie <airlied@redhat.com>