- 08 2月, 2009 8 次提交
-
-
由 Jesse Barnes 提交于
Pull in an update from the 2D driver (hopefully the last one, future work should be done here and pulled back into xf86-video-intel as needed). Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Chris Wilson 提交于
Cleanup the object reference on the error paths. Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Jesse Barnes 提交于
Adds code to set up fence registers at execbuf time on pre-965 chips as necessary. Also fixes up a few bugs in the pre-965 tile register support (get_order != ffs). The number of fences available to the kernel defaults to the hw limit minus 3 (for legacy X front/back/depth), but a new parameter allows userspace to override that as needed. Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Eric Anholt 提交于
Previously, the caller would continue along without knowing that the function failed, resulting in potential mis-rendering. Right now vm_fault just returns SIGBUS in that case, and we may need to disable signal handling to avoid that happening. Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Eric Anholt 提交于
We'd love to just be using PAT, but even on chips with PAT it gets disabled sometimes due to an errata. It would probably be better to have pat_enabled exported and only bother with this when !pat_enabled. Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Eric Anholt 提交于
This saves startup time from probing SDVO, and saves setting up HDMI outputs on G4X devices that don't have them. Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Eric Anholt 提交于
Fixes hangs when starting X for the second time. Signed-off-by: NEric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@linux.ie>
-
由 Dave Airlie 提交于
this solves a regression from http://bugzilla.kernel.org/show_bug.cgi?id=12441Reported-by: NDaniel Vetter <daniel@ffwll.ch> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 03 2月, 2009 26 次提交
-
-
由 Dave Airlie 提交于
This code is always called under the lock from the higher layers, so need to go locking it here. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI hotplug: Change link order of pciehp & acpiphp PCI hotplug: fakephp: Allocate PCI resources before adding the device PCI MSI: Fix undefined shift by 32 PCI PM: Do not wait for buses in B2 or B3 during resume PCI PM: Power up devices before restoring their state PCI PM: Fix hibernation breakage on EeePC 701 PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs PCI PM: Fix suspend error paths and testing facility breakage
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6: slub: fix per cpu kmem_cache_cpu array memory leak kmalloc: return NULL instead of link failure
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc由 Linus Torvalds 提交于
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks powerpc: Fix oops on some machines due to incorrect pr_debug() powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net powerpc/5200: update device tree binding documentation powerpc/5200: Bugfix for PCI mapping of memory and IMMR powerpc/5200: update defconfigs
-
由 Linus Torvalds 提交于
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched_rt: don't use first_cpu on cpumask created with cpumask_and sched: fix buddie group latency sched: clear buddies more aggressively sched: symmetric sync vs avg_overlap sched: fix sync wakeups cpuset: fix possible deadlock in async_rebuild_sched_domains
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6由 Linus Torvalds 提交于
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits) V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio V4L/DVB (10229): ivtv: fix memory leak V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming. V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback. V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged V4L/DVB (10287): af9015: fix second FE V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at ffffffff V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown V4L/DVB (10257): em28xx: Fix for KWorld 330U Board V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97 V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings. V4L/DVB (10243): em28xx: fix compile warning V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081) ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: pxamci: enable DMA for write ops after CMD/RESP pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x()) ricoh_mmc: Use suspend_late/resume_early mmci: Add support for ST Micro derivate mmc: Add a MX2/MX3 specific SDHC driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: icside: fix PCB version 6 support (v2) tx4939ide: typo fix and minor cleanup ide: add CS5536 host driver (v3) ide: Force VIA IDE legacy interrupts for AmigaOne boards IDE: Unregister and disable devices if initialization fails. ide: fix ide_register_port() failure handling ide: struct device - replace bus_id with dev_name(), dev_set_name() ide-cd: fix DMA for non bio-backed requests
-
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb由 Linus Torvalds 提交于
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: uwb: lock rc->rsvs_lock with spin_lock_bh() wusb: timeout when waiting for ASL/PZL updates in whci-hcd uwb: remove unused #include <version.h>'s wusb: return -ENOTCONN when resetting a port with no connected device uwb: safely remove all reservations
-
git://git.kernel.dk/linux-2.6-block由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: block: add text file detailing queue/ sysfs files bio.h: If they MUST be inlined, then use __always_inline Fix misleading comment in bio.h block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT block: fix oops in blk_queue_io_stat()
-
由 Mark McLoughlin 提交于
The host really shouldn't be notifying us of config changes before the device status is VIRTIO_CONFIG_S_DRIVER or VIRTIO_CONFIG_S_DRIVER_OK. However, if we do happen to be interrupted while we're not attached to a driver, we really shouldn't oops. Prevent this simply by checking that device->driver is non-NULL before trying to notify the driver of config changes. Problem observed by doing a "set_link virtio.0 down" with QEMU before the net driver had been loaded. Signed-off-by: NMark McLoughlin <markmc@redhat.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Eric Dumazet 提交于
Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is using a lot of memory. Each 'struct module' contains an [NR_CPUS] array of full cache lines. This patch uses existing infrastructure (percpu_modalloc() & percpu_modfree()) to allocate percpu space for the refcount storage. Instead of wasting NR_CPUS*128 bytes (on i386), we now use nr_cpu_ids*sizeof(local_t) bytes. On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce size of module files by about 2 Mbytes. (1Kb per module) Instead of having all refcounters in the same memory node - with TLB misses because of vmalloc() - this new implementation permits to have better NUMA properties, since each CPU will use storage on its preferred node, thanks to percpu storage. Signed-off-by: NEric Dumazet <dada1@cosmosbay.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Cliff Brake 提交于
With the PXA270 MMC hardware, there seems to be an issue of data corruption on writes where a 4KB data block is offset by one byte. If we delay enabling the DMA for writes until after the CMD/RESP has finished, the problem seems to be fixed. related to PXA270 Erratum #91 Tested-by: NVernon Sauder <VernonInHand@gmail.com> Signed-off-by: NCliff Brake <cbrake@bec-systems.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
由 Cliff Brake 提交于
Signed-off-by: NCliff Brake <cbrake@bec-systems.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
由 philipl@overt.org 提交于
If ricoh_mmc suspends before sdhci_pci, it will pull the card out from under the controller, which could leave the system in a very confused state. Using suspend_late/resume_early ensures that sdhci_pci suspends first and resumes second. Signed-off-by: NPhilip Langdale <philipl@overt.org> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
由 Linus Walleij 提交于
This patch adds support for the ST Microelectronics version of the PL180 PrimeCell. They use designer ID 0x80 and have a few alterations/bugfixes related to open drain and HW flow control. They also add some SDIO registers, I am unsure if these are in ST HW only or if this is things also added in later ARM revisions, but they are included in the mmci.h file for completeness. Signed-off-by: NLinus Walleij <linus.walleij@ericsson.com> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
由 Sascha Hauer 提交于
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically the same as in the MX1, but unlike the MX1 controller the MX2 controller just works as expected. Since the MX1 driver has more workarounds for bugs than anything else I had no success with supporting MX1 and MX2 in a sane way in one driver. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
We need to pass struct ide_port_info also to ide_host_register(). v2: Fix v5/v6 mismatch noticed by Russell. Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Atsushi Nemoto 提交于
The bcount is greater than 0 and less than or equal to 0x10000. Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'. Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen) to IDE subsystem. Changes done while at it: * Reprogram PIO/MWDMA timings if needed before and after DMA transfer (chipset uses shared PIO/MWDMA timings). * Fix cable detection to report 80-wires cable if BIOS set it for any device on a port (IDE core will do drive-side cable detection later). * Don't disable UDMA while programming PIO timings. * Simplify PCI/MSR support. Pros of having IDE host driver in addition to libata's one: * IDE is much lighter than SCSI+libata, the host driver itself is also a bit smaller: text data bss dec hex filename 1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o 1242 128 4 1374 55e drivers/ide/cs5536.o * This allows use of IDE features which are unavailable under libata. v2: * Fixes per review from Sergei: - simplify dependency check in Kconfig - use IDE_DRV_MASK also for ->drive_data - disable UDMA when programming MWDMA - program new DTC timings only when necessary - fix printk() level in cs5536_init_one() * Fix patch description according to comments from Alan and Sergei. v3: * Smarter masking of UDMA bits per Sergei's suggestion. Cc: Martin K. Petersen <mkp@mkp.net> Cc: Karl Auerbach <karl@iwl.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Gerhard Pircher 提交于
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the Pegasos). Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net> Cc: "Grant Likely" <grant.likely@secretlab.ca> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Ian Campbell 提交于
On reboot the loop in device_shutdown gets confused by these partially initialized devices and goes into an infinite loop. Therefore unregister and disable these devices. Signed-off-by: NIan Campbell <ian.campbell@citrix.com> [bart: remove leftover hwif->present clearing + update patch description] Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Factor out port freeing from ide_host_free() to ide_free_port(). * Add ide_disable_port() and use it on ide_register_port() failure. Cc: Ian Campbell <Ian.Campbell@citrix.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Kay Sievers 提交于
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org> Cc: linux-ide@vger.kernel.org Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Borislav Petkov 提交于
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=12320. Signed-off-by: NBorislav Petkov <petkovbb@gmail.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 David Vrabel 提交于
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-upstream
-
- 02 2月, 2009 6 次提交
-
-
由 Jens Axboe 提交于
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
由 Alberto Bertogli 提交于
bvec_kmap_irq() and bvec_kunmap_irq() comments say they MUST be inlined, so mark them as __always_inline. Signed-off-by: NAlberto Bertogli <albertito@blitiri.com.ar> Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
由 Alberto Bertogli 提交于
The comment says "remember to add offset!", but the function already adds it. Signed-off-by: NAlberto Bertogli <albertito@blitiri.com.ar> Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
由 Pekka Enberg 提交于
-
由 Jens Axboe 提交于
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
由 Jens Axboe 提交于
Some initial probe requests don't have disk->queue mapped yet, so we can't rely on a non-NULL queue in blk_queue_io_stat(). Wrap it in blk_do_io_stat(). Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-