This adds the shared devicetree files for the Veyron device family.
They are split, as not all veyron devices are chromebooks and
not all contain a sd-card slot.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>

This patch creates a sbs-battery fragment for batteries connected
to the i2c tunnel of the cros-ec embedded controller.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NDouglas Anderson <dianders@chromium.org>

This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.

The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NRomain Perier <romain.perier@gmail.com>

The watchdog irq is actually SPI 79, which translates to the original
111 in the manual where the SPI irqs start at 32.
The current dw_wdt driver does not use the irq at all, so this issue
never surfaced. Nevertheless fix this for a time we want to use the irq.

Fixes: 2ab557b7 ("ARM: dts: rockchip: add core rk3288 dtsi")
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>

Adds ramp delay for the vdd_cpu output. It removes warning "ramp_delay
not set" emitted by the function regulator_set_voltage_time_sel() by the
same time, which floods kernel logs.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Which fixes warning "no reset control found" by the same time
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The Broadcom NAND driver is used by brcmstb, bcm63xx, bcm5301x and
Cygnus/iProc under mach-bcm, this is enough critical mass to enable it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

This reverts 7dc95b40 ("ARM: BCM: Enable
NAND support for iProc SoCs") since it creates an unmet dependency for
MTD_NAND_BRCMNAND which depends on MTD and MTD_NAND, this results in the
following build failure for brcmnand:

 LD      init/built-in.o
drivers/built-in.o: In function `brcmnand_remove':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:2234:
undefined reference to `nand_release'
drivers/built-in.o: In function `brcmnand_init_cs':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1933:
undefined reference to `nand_scan_ident'
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1958:
undefined reference to `nand_scan_tail'
Makefile:931: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1

Instead, select this driver an all dependencies on the
multi_v7_defconfig.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

at91sam9g45, at91sam9x5 and sama5 SoCs should not use
"atmel,at91sam9rl-udc" for their USB device compatible property since
this compatible is attached to a specific hardware bug fix.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>  #4.0+
Signed-off-by: NKevin Hilman <khilman@linaro.org>

To be consistent with other genalloc interface namings, rename
dev_get_gen_pool() to gen_pool_get().  The original omitted "dev_" prefix
is removed, since it points to argument type of the function, and so it
does not bring any useful information.

[akpm@linux-foundation.org: update arch/arm/mach-socfpga/pm.c]
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch updates the Ethernet DT nodes for Armada XP SoCs with the
compatible string "marvell,armada-xp-neta".
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Fixes: 77916519 ("arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irq_data->hwirq is not guaranteed to be the same as irq_data->irq. It
might be in that particular case, but it's wrong nevertheless.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Roland Stigge <stigge@antcom.de>

Nobody used these hooks so they were removed from common code, and can now
be removed from the architectures.
Signed-off-by: NDominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we have many duplicates in definitions of
hugetlb_prefault_arch_hook.  In all architectures this function is empty.
Signed-off-by: NZhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu).  This includes remapping
the vDSO to the place it has at checkpoint time.

However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service.  So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.

This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold.  The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.

This patch (of 3):

This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)

The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.

The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.

In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we have many duplicates in definitions of huge_pmd_unshare.  In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.

This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: NZhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This backs out all changes that were added in the hip04-dt
branch after various boot problems were discovered in UEFI booting.
Reported-by: NTyler Baker <tyler.baker@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
[khilman: minor changelog updates]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Add support for the Arria10 SDRAM EDAC. Update the bindings document for
the new match string.
Signed-off-by: NThor Thayer <tthayer@opensource.altera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree@vger.kernel.org
Cc: dinguyen@opensource.altera.com
Cc: galak@codeaurora.org
Cc: grant.likely@linaro.org
Cc: ijc+devicetree@hellion.org.uk
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: m.chehab@samsung.com
Cc: mark.rutland@arm.com
Cc: pawel.moll@arm.com
Cc: robh+dt@kernel.org
Cc: tthayer.linux@gmail.com
Link: http://lkml.kernel.org/r/1433428128-7292-5-git-send-email-tthayer@opensource.altera.comSigned-off-by: NBorislav Petkov <bp@suse.de>

v3.18 changed handle_IRQ() to call __handle_domain_irq(), which now
rejects attempts to deliver IRQ0.  Since IRQ 0 is used as the timer
interrupt (just like the PIT on x86), this causes boot to fail as the
bogomips calibration never completes.

Fix this by shuffling all interrupts up by one.

Fixes: a71b092a ("ARM: Convert handle_IRQ to use __handle_domain_irq")
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The clock which was named as 'pll_clk' is actually not the clock source
of PLL in MIPI DSI. This patch fixes this disagreement.
Signed-off-by: NHyungwon Hwang <human.hwang@samsung.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The new CPU clock type allows the use of generic CPUfreq driver.
Switch Exynos4210 to using generic cpufreq driver.

Changes by Bartlomiej:
- removed non-Exynos4210 support for now

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>

The gemini code was installing its chained interrupt handler (which
enables the interrupt) before it was setting its data, which is bad if
the IRQ was previously pending.  Avoid this problem by converting it to
irq_set_chained_handler_and_data().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4z07-0002SO-Gv@rmk-PC.arm.linux.org.ukSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Convert SA11x0 (Neponset, SA1111, and UCB1x00 code) to use the new
irq_set_chained_handler_and_data() helper.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4yzx-0002S6-7p@rmk-PC.arm.linux.org.ukSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NJulien Grall <julien.grall@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

The current Armada XP suspend to RAM implementation, as added in
commit 27432825 ("ARM: mvebu: Armada XP GP specific
suspend/resume code") does not handle big-endian configurations
properly: the small bit of assembly code putting the DRAM in
self-refresh and toggling the GPIOs to turn off power forgets to
convert the values to little-endian.

This commit fixes that by making sure the two values we will write to
the DRAM controller register and GPIO register are already in
little-endian before entering the critical assembly code.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.19+
Fixes: 27432825 ("ARM: mvebu: Armada XP GP specific suspend/resume code")

Using xen/page.h will be necessary later for using common xen page
helpers.

As xen/page.h already include asm/xen/page.h, always use the later.
Signed-off-by: NJulien Grall <julien.grall@citrix.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Following the merge of "pinctrl: mvebu: armada-xp: rename spi to spi0"
by Linus Walleij, we need to adjust the Armada XP Device Tree
accordingly, by adjusting the pinctrl configuration for SPI pins.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This is now done in the I2C driver.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The GIC Hypervisor Configuration Register is used to enable
the delivery of virtual interupts to a guest, as well as to
define in which conditions maintenance interrupts are delivered
to the host.

This register doesn't contain any information that we need to
read back (the EOIcount is utterly useless for us).

So let's save ourselves some cycles, and not save it before
writing zero to it.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

According to the PSCI specification and the SMC/HVC calling
convention, PSCI function_ids that are not implemented must
return NOT_SUPPORTED as return value.

Current KVM implementation takes an unhandled PSCI function_id
as an error and injects an undefined instruction into the guest
if PSCI implementation is called with a function_id that is not
handled by the resident PSCI version (ie it is not implemented),
which is not the behaviour expected by a guest when calling a
PSCI function_id that is not implemented.

This patch fixes this issue by returning NOT_SUPPORTED whenever
the kvm PSCI call is executed for a function_id that is not
implemented by the PSCI kvm layer.

Cc: <stable@vger.kernel.org> # 3.18+
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The KVM-VFIO device is used by the QEMU VFIO device. It is used to
record the list of in-use VFIO groups so that KVM can manipulate
them.
Signed-off-by: NKim Phillips <kim.phillips@linaro.org>
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Until now we have been calling kvm_guest_exit after re-enabling
interrupts when we come back from the guest, but this has the
unfortunate effect that CPU time accounting done in the context of timer
interrupts occurring while the guest is running doesn't properly notice
that the time since the last tick was spent in the guest.

Inspired by the comment in the x86 code, move the kvm_guest_exit() call
below the local_irq_enable() call and change __kvm_guest_exit() to
kvm_guest_exit(), because we are now calling this function with
interrupts enabled.  We have to now explicitly disable preemption and
not enable preemption before we've called kvm_guest_exit(), since
otherwise we could be preempted and everything happening before we
eventually get scheduled again would be accounted for as guest time.

At the same time, move the trace_kvm_exit() call outside of the atomic
section, since there is no reason for us to do that with interrupts
disabled.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

We already check KVM_CAP_IRQFD in generic once enable CONFIG_HAVE_KVM_IRQFD,

kvm_vm_ioctl_check_extension_generic()
    |
    + switch (arg) {
    +   ...
    +   #ifdef CONFIG_HAVE_KVM_IRQFD
    +       case KVM_CAP_IRQFD:
    +   #endif
    +   ...
    +   return 1;
    +   ...
    + }
    |
    + kvm_vm_ioctl_check_extension()

So its not necessary to check this in arch again, and also fix one typo,
s/emlation/emulation.
Signed-off-by: NTiejun Chen <tiejun.chen@intel.com>
Acked-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

On VM entry, we disable access to the VFP registers in order to
perform a lazy save/restore of these registers.

On VM exit, we restore access, test if we did enable them before,
and save/restore the guest/host registers if necessary. In this
sequence, the FPEXC register is always accessed, irrespective
of the trapping configuration.

If the guest didn't touch the VFP registers, then the HCPTR access
has now enabled such access, but we're missing a barrier to ensure
architectural execution of the new HCPTR configuration. If the HCPTR
access has been delayed/reordered, the subsequent access to FPEXC
will cause a trap, which we aren't prepared to handle at all.

The same condition exists when trapping to enable VFP for the guest.

The fix is to introduce a barrier after enabling VFP access. In the
vmexit case, it can be relaxed to only takes place if the guest hasn't
accessed its view of the VFP registers, making the access to FPEXC safe.

The set_hcptr macro is modified to deal with both vmenter/vmexit and
vmtrap operations, and now takes an optional label that is branched to
when the guest hasn't touched the VFP registers.
Reported-by: NVikram Sethi <vikrams@codeaurora.org>
Cc: stable@kernel.org	# v3.9+
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

They use the "_INIT" macro and friends, and hence need to
source this header file, vs. relying on getting it implicitly.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The spc.o is built for ARCH_VEXPRESS_SPC -- which is bool, and hence
this code is either present or absent.  It will never be modular,
so using module_init as an alias for __initcall can be somewhat
misleading.

Fix this up now, so that we can relocate module_init from
init.h into module.h in the future.  If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.

Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups.  As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We removed __cpuinit support (leaving no-op stubs) quite some time ago.
However a new instance was added in commit 06cc5c1d
("ARM: hisi: enable hix5hd2 SoC")

Since we want to clobber the stubs soon, get this removed now.
Note that there would normally be a corresponding removal of
a ".previous" directive, but in this case it appears that this
single function file was never paired off with one.

Cc: Haifeng Yan <yanhaifeng@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We removed __cpuinit support (leaving no-op stubs) quite some time ago.
However this one crept back in as of commit a7a2b311
("ARM: rockchip: add smp bringup code").

Since we want to clobber the stubs soon, get this removed now.

Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We removed __cpuinit support (leaving no-op stubs) quite some time
ago.  However these ones crept back in as of commit 1ee89e22
("ARM: mvebu: add SMP support for Armada 375 and Armada 38x")

Since we want to clobber the stubs soon, get this removed now.
Note that there would normally be a corresponding removal of
a ".previous" directive for each __CPUINIT in asm files, but in
this case it appears that this single function file was never
paired off with one.

Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>