Amir Vadai says:

====================
net/mlx4: Mellanox driver update 07-11-2013

This patchset contains some enhancements and bug fixes for the mlx4_* drivers.
Patchset was applied and tested against commit: "9bb8ca86 virtio-net: switch to
use XPS to choose txq"
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each RX/TX ring and its CQ, allocation is done on a NUMA node that
corresponds to the core that the data structure should operate on.
The assumption is that the core number is reflected by the ring index.
The affected allocations are the ring/CQ data structures,
the TX/RX info and the shared HW/SW buffer.
For TX rings, each core has rings of all UPs.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is done to optimize FW/HW access to host memory.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently all TX/RX rings and completion queues are part of the
netdev priv structure and are allocated statically. This patch
will change the priv to hold only arrays of pointers and therefore
all TX/RX rings and completetion queues will be allocated
dynamically. This is in preparation for NUMA aware allocations.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow immediate activate of VGT->VST and VST->VGT transitions, without
the need of rebinding in mlx4_master_immediate_activate_vlan_qos().

Also in struct res_qp: add qp parameters (vlan_index,fvl,vlan_cntrol..)
to the saved set, in order to restore when move to VGT.
 - Clear at mlx4_RST2INIT_QP_wrapper()
 - Save at mlx4_INIT2RTR_QP_wrapper()
 - Restore at mlx4_vf_immed_vlan_work_handler()

Update mlx4_vf_immed_vlan_work_handler() to support VGT.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.

This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.

In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify RFS code to support applying filters for incoming UDP streams.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John Fastabend says:

====================
l2 hardware accelerated macvlans

This patch adds support to offload macvlan net_devices to the
hardware. With these patches packets are pushed to the macvlan
net_device directly and do not pass through the lower dev.

The patches here have made it through multiple iterations
each with a slightly different focus. First I tried to
push these as a new link type called "VMDQ". The patches
shown here,

http://comments.gmane.org/gmane.linux.network/237617

Following this implementation I renamed the link type
"VSI" and addressed various comments. Finally Neil
Horman picked up the patches and integrated the offload
into the macvlan code. Here,

http://permalink.gmane.org/gmane.linux.network/285658

The attached series is clean-up of his patches, with a
few fixes.

If folks find this series acceptable there are a few
items we can work on next. First broadcast and multicast
will use the hardware even for local traffic with this
series. It would be best (I think) to use the software
path for macvlan to macvlan traffic and save the PCIe
bus. This depends on how much you value CPU time vs
PCIE bandwidth. This will need another patch series
to flush out.

Also this series only allows for layer 2 mac forwarding
where some hardware supports more interesting forwarding
capabilities. Integrating with OVS may be useful here.

As always any comments/feedback welcome.

My basic I/O test is here but I've also done some link
testing, SRIOV/DCB with macvlans and others,

Changelog:
v2: two fixes to ixgbe when all features DCB, FCoE, SR-IOV
    are enabled with macvlans. A VMDQ_P() reference
    should have been accel->pool and do not set the offset
    of the ring index from dfwd add call. The offset is used
    by SR-IOV so clearing it can cause SR-IOV quue index's
    to go sideways. With these fixes testing macvlan's with
    SRIOV enabled was successful.
v3: addressed Neil's comments in ixgbe
    fixed error path on dfwd_add_station() in ixgbe
    fixed ixgbe to allow SRIOV and accelerated macvlans to
    coexist.
v4: Dave caught some strange indentation, fixed it here
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that l2 acceleration ops are in place from the prior patch,
enable ixgbe to take advantage of these operations.  Allow it to
allocate queues for a macvlan so that when we transmit a frame,
we can do the switching in hardware inside the ixgbe card, rather
than in software.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a operations structure that allows a network interface to export
the fact that it supports package forwarding in hardware between
physical interfaces and other mac layer devices assigned to it (such
as macvlans). This operaions structure can be used by virtual mac
devices to bypass software switching so that forwarding can be done
in hardware more efficiently.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

timecounter_init() was was called only after first potential
timecounter_read().
Moved mlx4_en_init_timestamp() before mlx4_en_init_netdev()
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"card2" is NULL here so I have changed it to use "id2" instead of
"card2->interface.id".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a bug in cpsw_probe() where we do:

	ndev->irq = platform_get_irq(pdev, 0);
	if (ndev->irq < 0) {

The problem is that "ndev->irq" is unsigned so the error handling
doesn't work.  I have changed it to a regular int.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently added a new error path and it needs a dev_put().

Fixes: 7adac1ec ('6lowpan: Only make 6lowpan links to IEEE802154 devices')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On top of commit 366cddb4 "IB/rdma_cm: TOS <=> UP mapping for IBoE", add
support for case vlan egress map is used.

When the IBoE session is being set over a vlan, inherit the socket priority
to vlan priority mapping which was configured for the vlan device egress map.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a method for read-only access to the vlan device egress mapping.

Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.

Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a96865 "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If build_skb fails the memory associated with the ring buffer is freed but
the ri->data member is not zeroed in this case. This causes a double-free
of this memory in tg3_free_rings->... path. The patch moves this block after
setting ri->data to NULL.
It would be nice to fix this bug also in stable >= v3.4 trees.

Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ariel Elior will take over the bnx2x maintenance.

It's been a pleasure!
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_filter isn't freed if bpf_func is equal to sk_run_filter.

This memory leak was introduced by v3.12-rc3-224-gd45ed4a4
"net: fix unsafe set_memory_rw from softirq".

Before this patch sk_filter was freed in sk_filter_release_rcu,
now it should be freed in bpf_jit_free.

Here is output of kmemleak:
unreferenced object 0xffff8800b774eab0 (size 128):
  comm "systemd", pid 1, jiffies 4294669014 (age 124.062s)
  hex dump (first 32 bytes):
    00 00 00 00 0b 00 00 00 20 63 7f b7 00 88 ff ff  ........ c......
    60 d4 55 81 ff ff ff ff 30 d9 55 81 ff ff ff ff  `.U.....0.U.....
  backtrace:
    [<ffffffff816444be>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811845af>] __kmalloc+0xef/0x260
    [<ffffffff81534028>] sock_kmalloc+0x38/0x60
    [<ffffffff8155d4dd>] sk_attach_filter+0x5d/0x190
    [<ffffffff815378a1>] sock_setsockopt+0x991/0x9e0
    [<ffffffff81531bd6>] SyS_setsockopt+0xb6/0xd0
    [<ffffffff8165f3e9>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff

v2: add extra { } after else

Fixes: d45ed4a4 ("net: fix unsafe set_memory_rw from softirq")
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrey Vagin <avagin@openvz.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Erik Hugne says:

====================
tipc: message reassembly using fragment chain

We introduce a new reassembly algorithm that improves performance
and eliminates the risk of causing out-of-memory situations.

v3: -Use skb_try_coalesce, and revert to fraglist if this does not succeed.
    -Make sure reassembly list head is uncloned.

v2: -Rebased on Ying's indentation fix.
    -Node unlock call in msg_fragmenter case moved from patch #2 to #1.
     ('continue' with this lock held would cause spinlock recursion if only
      patch #1 is used)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If appending a received fragment to the pending fragment chain
in a unicast link fails, the current code tries to force a retransmission
of the fragment by decrementing the 'next received sequence number'
field in the link. This is done under the assumption that the failure
is caused by an out-of-memory situation, an assumption that does
not hold true after the previous patch in this series.

A failure to append a fragment can now only be caused by a protocol
violation by the sending peer, and it must hence be assumed that it
is either malicious or buggy.  Either way, the correct behavior is now
to reset the link instead of trying to revert its sequence number.
So, this is what we do in this commit.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the first fragment of a long data data message is received on a link, a
reassembly buffer large enough to hold the data from this and all subsequent
fragments of the message is allocated. The payload of each new fragment is
copied into this buffer upon arrival. When the last fragment is received, the
reassembled message is delivered upwards to the port/socket layer.

Not only is this an inefficient approach, but it may also cause bursts of
reassembly failures in low memory situations. since we may fail to allocate
the necessary large buffer in the first place. Furthermore, after 100 subsequent
such failures the link will be reset, something that in reality aggravates the
situation.

To remedy this problem, this patch introduces a different approach. Instead of
allocating a big reassembly buffer, we now append the arriving fragments
to a reassembly chain on the link, and deliver the whole chain up to the
socket layer once the last fragment has been received. This is safe because
the retransmission layer of a TIPC link always delivers packets in strict
uninterrupted order, to the reassembly layer as to all other upper layers.
Hence there can never be more than one fragment chain pending reassembly at
any given time in a link, and we can trust (but still verify) that the
fragments will be chained up in the correct order.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a message fragment is received in a broadcast or unicast link,
the reception code will append the fragment payload to a big reassembly
buffer through a call to the function tipc_recv_fragm(). However, after
the return of that call, the logics goes on and passes the fragment
buffer to the function tipc_net_route_msg(), which will simply drop it.
This behavior is a remnant from the now obsolete multi-cluster
functionality, and has no relevance in the current code base.

Although currently harmless, this unnecessary call would be fatal
after applying the next patch in this series, which introduces
a completely new reassembly algorithm. So we change the code to
eliminate the redundant call.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".

This patch adds an MDIO driver which handles the MII bus.
Signed-off-by: NJonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new documentation for the packets_per_slave option available
for balance-rr mode.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aims to extend round-robin mode with a new option called
packets_per_slave which can have the following values and effects:
0 - choose a random slave
1 (default) - standard round-robin, 1 packet per slave
 >1 - round-robin when >1 packets have been transmitted per slave
The allowed values are between 0 and 65535.
This patch also fixes the comment style in bond_xmit_roundrobin().
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check user-defined length in snmp ioctl request and allow request
only if it fits into a qeth command buffer.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: NHeiko Carstens <heicars2@linux.vnet.ibm.com>
Reported-by: NNico Golde <nico@ngolde.de>
Reported-by: NFabian Yamaguchi <fabs@goesec.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just an unnecessary semicolon that should be removed...

Whitespace neatening of macro too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more standard logging style.

Convert smsc_<level> macros to use netif_<level>.
Remove unused #define PFX
Add pr_fmt and neaten pr_<level> uses.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's unused, remove it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to use a percpu structure vq_index to record the cpu to queue
mapping, this is suboptimal since it duplicates the work of XPS and
loses all other XPS functionality such as allowing user to configure
their own transmission steering strategy.

So this patch switches to use XPS and suggest a default mapping when
the number of cpus is equal to the number of queues. With XPS support,
there's no need for keeping per-cpu vq_index and .ndo_select_queue(),
so they were removed also.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now rt6_alloc_cow() is only called by ip6_pol_route() when
rt->rt6i_flags doesn't contain both RTF_NONEXTHOP and RTF_GATEWAY,
and rt->rt6i_flags hasn't been changed in ip6_rt_copy().
So there is no neccessary to judge whether rt->rt6i_flags contains
RTF_GATEWAY or not.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1e2bd517 ("udp6: Fix udp
fragmentation for tunnel traffic.") changed the calculation if
there is enough space to include a fragment header in the skb from a
skb->mac_header dervived one to skb_headroom. Because we already peeled
off the skb to transport_header this is wrong. Change this back to check
if we have enough room before the mac_header.

This fixes a panic Saran Neti reported. He used the tbf scheduler which
skb_gso_segments the skb. The offsets get negative and we panic in memcpy
because the skb was erroneously not expanded at the head.
Reported-by: NSaran Neti <Saran.Neti@telus.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit cc9d4598 'net: mv643xx_eth: use of_phy_connect if phy_node
present' made the call to phy_scan optional, if the DT has a link to
the phy node.

However phy_scan has the side effect of calling phy_addr_set, which
writes the phy MDIO address to the ethernet controller. If phy_addr_set
is not called, and the bootloader has not set the correct address then
the driver will fail to function.

Tested on Kirkwood.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sockets marked with IP_PMTUDISC_INTERFACE won't do path mtu discovery,
their sockets won't accept and install new path mtu information and they
will always use the interface mtu for outgoing packets. It is guaranteed
that the packet is not fragmented locally. But we won't set the DF-Flag
on the outgoing frames.

Florian Weimer had the idea to use this flag to ensure DNS servers are
never generating outgoing fragments. They may well be fragmented on the
path, but the server never stores or usees path mtu values, which could
well be forged in an attack.

(The root of the problem with path MTU discovery is that there is
no reliable way to authenticate ICMP Fragmentation Needed But DF Set
messages because they are sent from intermediate routers with their
source addresses, and the IMCP payload will not always contain sufficient
information to identify a flow.)

Recent research in the DNS community showed that it is possible to
implement an attack where DNS cache poisoning is feasible by spoofing
fragments. This work was done by Amir Herzberg and Haya Shulman:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>

This issue was previously discussed among the DNS community, e.g.
<http://www.ietf.org/mail-archive/web/dnsext/current/msg01204.html>,
without leading to fixes.

This patch depends on the patch "ipv4: fix DO and PROBE pmtu mode
regarding local fragmentation with UFO/CORK" for the enforcement of the
non-fragmentable checks. If other users than ip_append_page/data should
use this semantic too, we have to add a new flag to IPCB(skb)->flags to
suppress local fragmentation and check for this in ip_finish_output.

Many thanks to Florian Weimer for the idea and feedback while implementing
this patch.

Cc: David S. Miller <davem@davemloft.net>
Suggested-by: NFlorian Weimer <fweimer@redhat.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bjørn Mork says:

====================
The huawei_cdc_ncm driver.

Enrico has been kind enough to let me repost his driver with the changes
requested by Oliver Neukum during the last review of this series.

The changes I have made from Enricos original v5 series to this version
are:

v6:
 - fix to avoid corrupting drvstate->pmcount
 - fix error return value from huawei_cdc_ncm_suspend()
 - drop redundant testing for subdriver->suspend during resume
 - broke a few lines to keep within the 80 columns recommendation
 - rebased on top of current net-next

Enrico's orginal introduction to the v5 series follows below.  It explains
the background much better than I can.

Bjørn

[quote Enrico Mioso]

So this is a new, revised, edition of the huawei_cdc_ncm.c driver, which
supports devices resembling the NCM standard, but using it also as a mean
to encapsulate other protocols, as is the case for the Huawei E3131 and
E3251 modem devices.
Some precisations are needed however - and I encourage discussion on this: and
that's why I'm sending this message with a broader CC.
Merging those patches might change:
- the way Modem Manager interacts with those devices
- some regressions might be possible if there are some unknown firmware
  variants around (Franko?)

First of all: I observed the behaviours of two devices.
Huawei E3131: this device doesn't accept NDIS setup requests unless they're
sent via the embedded AT channel exposed by this driver.
So actually we gain funcionality in this case!

The second case, is the Huawei E3251: which works with standard NCM driver,
still exposing an AT embedded channel. Whith this patch set applied, you gain
some funcionality, loosing the ability to catch standard NCM events for now.
The device will work in both ways with no problems, but this has to be
acknowledged and discussed. Might be we can develop this driver further to
change this, when more devices are tested.

We where thinking Huawei changed their interfaces on new devices - but probably
this driver only works around a nice firmware bug present in E3131, which
prevented the modem from being used in NDIS mode.

I think committing this is definitely wortth-while, since it will allow for
more Huawei devices to be used without serial connection. Some devices like the
E3251 also, reports some status information only via the embedded AT channel,
at least in my case.
Note: I'm not subscribed to any list except the Modem Manager's one, so please
CC me, thanks!!

[/quote]

Enrico Mioso (3):
  net: cdc_ncm: Export cdc_ncm_{tx,rx}_fixup functions for re-use
  net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver
  net: cdc_ncm: remove non-standard NCM device IDs
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove device IDs of NCM-like (but not NCM-conformant) devices, that are
handled by the huawwei_cdc_ncm driver now.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver supports devices using the NCM protocol as an encapsulation layer
for other protocols, like the E3131 Huawei 3G modem. This drivers approach was
heavily inspired by the qmi_wwan/cdc_mbim approach & code model.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>