- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
  from a free IOtag pool.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.

Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
  timer calibration (around 300 miilisecs earlier). So there is a
  window if an accept comes during this time HBA would have initiated
  an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
  when asic blck is programmed flash controller's continuous access
  blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
  initialization, since not doing so will cause LPU to be
  uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Introduced IOC poll mechanism which replaces current interrupt
  based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
  register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
  1. Use the queue_process flag to see if iocfc configuration is done
     in INTX mode.
  2. Split the MSIX handler installation in two - one for IOC intr
     handler and the other for cpe/rme queue handler - and delay
     assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
  only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
  firmware response.
- Removed queue register offset initializations and added register offsets
  to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
  mailbox interfaces.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Avoid the use of hardware defined structure bfi_sge_s for DMA
  requests in host.

- Defined a generic address len pair to represent a DMA memory chunk
  (bfi_alen_s).
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes:

drivers/scsi/sun3_NCR5380.c:475: warning: ‘merge_contiguous_buffers’ defined but not used
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes a.o.:

drivers/scsi/sun3_scsi.h:225:5: warning: "NDEBUG" is not defined
drivers/scsi/sun3_scsi.h:345:14: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/sun3_scsi.h:351:14: warning: "NDEBUG_TAGS" is not defined
drivers/scsi/sun3_scsi.h:357:14: warning: "NDEBUG_MERGING" is not defined
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes:

drivers/scsi/sun3_NCR5380.c:1448:5: warning: "NCR_TIMEOUT" is not defined
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

and call it from sun3scsi_release(), cfr. the other NCR5380 drivers.

This fixes:

drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

WARNING: vmlinux.o(.text+0x18545c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x18556c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187692): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187770): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes:

drivers/scsi/mac_scsi.c:220:5: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/mac_scsi.c:271:5: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

WARNING: vmlinux.o(.text+0x1ecd3e): Section mismatch in reference from the function macscsi_detect() to the function .devinit.text:NCR5380_init()
WARNING: vmlinux.o(.text+0x1ecddc): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x1ece60): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

and call it from atari_scsi_release(), cfr. the other NCR5380 drivers.

This fixes:

drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add ISA PNP IDs of the following cards to aha152x driver:
AVA-1502
AVA-1505
AHA-1510
AVA-1515
AHA-1520
AHA-1522
AHA-1530
AHA-1532
AIC-6360
(list from SCSI.INF file)

This makes my AHA-1530P card (has ADP3015 ID) work automatically.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch resulted from the discussion at
https://bugzilla.novell.com/show_bug.cgi?id=679277,
https://bugzilla.novell.com/show_bug.cgi?id=681840 .
Signed-off-by: NWerner Fink <werner@novell.com>
Signed-off-by: NAnkit Jain <jankit@suse.de>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Noticed that when the sysfs interface of the SCSI SES
driver was used to request a fault indication the LED
flashed but the buzzer didn't sound. So it was doing
what REQUEST IDENT (locate) should do.

Changelog:
   - fix the setting of REQUEST FAULT for the device slot
     and array device slot elements in the enclosure control
     diagnostic page
   - note the potentially defective code that reads the
     FAULT SENSED and FAULT REQUESTED bits from the enclosure
     status diagnostic page

The attached patch is against git/scsi-misc-2.6
Signed-off-by: NDouglas Gilbert <dgilbert@interlog.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

commit 8ce7955a ("[SCSI] atari_NCR5380:
update_timeout removal") removed all users, but not the avtual variable.
Suggested-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Using the current NEXT() macro for both lvalues and rvalues gives:

In file included from drivers/scsi/sun3_scsi.c:623:
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_queue_command_lck’:
drivers/scsi/sun3_NCR5380.c:993: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_main’:
drivers/scsi/sun3_NCR5380.c:1147: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_information_transfer’:
drivers/scsi/sun3_NCR5380.c:2277: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c:2333: warning: assignment discards qualifiers from pointer target type

Change NEXT() to operate on rvalues only(), and introduce SET_NEXT() to
operate on lvalues, as is done in drivers/scsi/atari_NCR5380.c.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Deleting NPIV port causes a kernel panic when the NPIV port is in the same zone
as the physical port and shares the same LUN. This happens due to the fact that
vport destroy and unsolicited ELS are scheduled to run on the same workqueue,
and vport destroy destroys the lport and the unsolicited ELS tries to access
the invalid lport.  This patch fixes this issue by maintaining a list of valid
lports and verifying if the lport is valid or not before accessing it.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Do not set io_req->sc_cmd to NULL until bnx2fc_unmap_sg_list() is called to
enable it to unmap the DMA mappings.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

NIC partitioned interfaces reports the speed of 2500 which was not handled by
the driver.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:

In file included from arch/x86/include/asm/uaccess.h:573,
                 from include/linux/uaccess.h:5,
                 from include/linux/highmem.h:7,
                 from include/linux/pagemap.h:10,
                 from include/linux/blkdev.h:12,
                 from drivers/scsi/lpfc/lpfc_debugfs.c:21:
In function 'copy_from_user':
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct

presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Use chipset-specific irq installers
  drm/i915: forcewake fix after reset
  drm/i915: add Ivy Bridge page flip support
  drm/i915: split page flip queueing into per-chipset functions

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Connector: Correctly set the error code in case of success when dispatching receive callbacks
  Connector: Set the CN_NETLINK_USERS correctly
  pti: PTI semantics fix in pti_tty_cleanup.
  pti: ENXIO error case memory leak PTI fix.
  pti: double-free security PTI fix
  drivers:misc: ti-st: fix skipping of change remote baud
  drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
  st_kim: Handle case of no device found for ID 0
  firmware: fix GOOGLE_SMI kconfig dependency warning

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  MAINTAINERS: add myself as maintainer of USB/IP
  usb: r8a66597-hcd: fix cannot detect low/full speed device
  USB: ehci-ath79: fix a NULL pointer dereference
  USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
  usb/isp1760: Fix bug preventing the unlinking of control urbs
  USB: Fix up URB error codes to reflect implementation.
  xhci: Always set urb->status to zero for isoc endpoints.
  xhci: Add reset on resume quirk for asrock p67 host
  xHCI 1.0: Incompatible Device Error
  USB: don't let errors prevent system sleep
  USB: don't let the hub driver prevent system sleep
  USB: change maintainership of ohci-hcd and ehci-hcd
  xHCI 1.0: Force Stopped Event(FSE)
  xhci: Don't warn about zeroed bMaxBurst descriptor field.
  USB: Free bandwidth when usb_disable_device is called.
  xhci: Reject double add of active endpoints.
  USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
  usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
  usb: musb: host: compare status for negative error values

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
  amba pl011: platform data for reg lockup and glitch v2
  amba pl011: workaround for uart registers lockup
  tty: n_gsm: improper skb_pull() use was leaking framed data
  tty: n_gsm: Fixed logic to decode break signal from modem status
  TTY: ntty, add one more sanity check
  TTY: ldisc, do not close until there are readers
  8250: Fix capabilities when changing the port type
  8250_pci: Fix missing const from merges
  ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
  serial: ioremap warning fix for jsm driver.
  8250_pci: add -ENODEV code for Intel EG20T PCH

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: comedi: fix build breakages on some platforms
  Staging: brcm80211: disable drivers except for X86 or MIPS platforms
  Staging: brcm80211: disable drivers for PPC platforms
  Staging: iio: Make IIO depend on GENERIC_HARDIRQS
  Staging: mei: fix suspend failure
  Staging: fix iio builds when IIO_RING_BUFFER is not enabled
  Staging: Comedi: Build only on arches providing PAGE_KERNEL_NOCACHE
  Staging: fix more iio builds when IIO_RING_BUFFER is not enabled

* 'for-linus' of git://neil.brown.name/md:
  md: avoid endless recovery loop when waiting for fail device to complete.

Konstantin Belousov pointed out that 4697995b replaced the generic
i915_driver_irq_*install() functions with chipset specific routines
accessible only through driver->irq_*install(). So update the sanity
check in i915_request_wait() to match.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

The failure is as follows:

1. Userspace gets forcewake lock, lock count >=1
2. GPU hang/reset occurs (forcewake bit is reset)
3. count is now incorrect

The failure can only occur when using the forcewake userspace lock.

This has the unfortunate consequence of messing up the driver as well as
userspace, unless userspace closes the debugfs file, the kernel will
never end up waking the GT since the refcount will be > 1.

The solution is to try to recover the correct forcewake state based on
the refcount. There is a period of time where userspace reads/writes may
occur after the reset, before the GT has been forcewaked. The interface
was never designed to be a perfect solution for userspace reads/writes,
and the kernel portion is fixed by this patch.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

/proc/PID/io may be used for gathering private information.  E.g.  for
openssh and vsftpd daemons wchars/rchars may be used to learn the
precise password length.  Restrict it to processes being able to ptrace
the target process.

ptrace_may_access() is needed to prevent keeping open file descriptor of
"io" file, executing setuid binary and gathering io information of the
setuid'ed process.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.

We should check if the device is faulty before considering it to be a
spare.  This will avoid trying to start a recovery that cannot
proceed.

This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.

Cc: stable@kernel.org
Reported-by: NJim Paradis <james.paradis@stratus.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.

Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>