The ethmac node has to be configured for each board due to different
pinctrl nodes for RGMII/RMII. Thus the phy-mode should be specified at
the same place (= in the board .dts), making it easier to read the board
.dts file (because the phy-mode is stated explicitly, without requiring
developers to read all "parent" .dtsi as well).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add the SAR ADC to meson-gxbb.dtsi and meson-gxl.dtsi. GXBB provides a
10-bit ADC while GXL and GXM provide a 12-bit ADC.
Some boards use resistor ladder buttons connected through one of the ADC
channels. On newer devices (GXL and GXM) some boards use pull-ups/downs
to change the resistance (and thus the ADC value) on one of the ADC
channels to indicate the board revision.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

All Meson GX SoCs (GXBB, GXL and GXM) have a PWM controller within the
AO domain. When one of the board's LEDs is connected to one of the AO
PWM pins then this can be used to dim that LED (when the leds-pwm driver
is used).
Add the pwm_AO_ab to allow such devices to use the leds-pwm driver.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The Amlogic Meson GXBB/GXL/GXM secure monitor uses part of the memory space,
this patch adds these reserved zones.

Without such reserved memory zones, running the following stress command :
$ stress-ng --vm 16 --vm-bytes 128M --timeout 10s
multiple times:

Could lead to the following kernel crashes :
[   46.937975] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
...
[   47.058536] Internal error: Attempting to execute userspace memory: 8600000f [#3] PREEMPT SMP
...
Instead of the OOM killer.

Fixes: 4f24eda8 ("ARM64: dts: Prepare configs for Amlogic Meson GXBaby")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
[khilman: added Fixes tag, added _reserved and unit addresses]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This adds the missing node for the uart_AO_B port to the meson-gx.dtsi
(as this is supported by GXBB, GXL and GXM) along with the required
pinctrl pins. This is required as some boards are using it (the boards
from the Khadas VIM series for example have it exposed on the pin
headers).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

SCPI and SRAM are identical on GXBB and GXL. Moving the corresponding
nodes to meson-gx adds support for the thermal sensor on GXL based
devices.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
[khilman: add scpi_clocks label]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
boards.
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

meson-gx.dtsi was directly derived from meson-gxbb.dtsi, so keep the
copyrights in chronological order to not give a wrong impression.

Fixes: c328666d ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

In order to remove the boot warning :
[    2.290933] Unable to detect cache hierarchy from DT for CPU 0
And add missing L2 cache hierarchy information, add a simple l2 cache node
and reference it from the A53 cpu nodes.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Move all non-gxbb specific nodes to a common GX dtsi.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>