This patch replaces the "cs-gpio" from "controller-data" node
as was specified in the old binding and uses the standard
"cs-gpios" property expected by the SPI core as is defined now
in the spi-s3c64xx driver DT binding.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle
Correction(DCC) to operate safely at frequencies >= 1.4GHz.

Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides
this support.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Adds HDMI audio sDMA properties.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Adds HDMI audio sDMA properties.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add the necessary DTS nodes to enable the micro-HDMI output on Parlor
board.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.

This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.

The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch add support for lcd display on gta04 board. Display control
is connected to spi (used spi bitbang driver).
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a single HDMI output. Add the necessary display
information, including pinmuxing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a tca6424a I/O expander. Add it to the .dts file.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add OMAP5 DSS nodes to omap5.dtsi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am43x-epos-evm's LCD panel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for the display subsystem for AM4372. The DSS on AM4372 is
basically OMAP3's DSS, without DSI and VENC blocks.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

memblock is now fully integrated into the kernel and is the prefered
method for tracking memory. Rather than reinvent the wheel with
meminfo, migrate to using memblock directly instead of meminfo as
an intermediate.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NLeif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Arndale-Octa board is always configured to work with trustzone
firmware binary. Added DTS node entry to enable this support.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add pmusysreg node for Exynos3250 to access PMU
(Power Management Unit) register in a centralized way using
syscon driver.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds new exynos3250.dtsi to support Exynos3250 SoC
based on Cortex-A7 dual core and includes following dt nodes:

- GIC interrupt controller
- Pinctrl to control GPIOs
- Clock controller
- CPU information (Cortex-A7 dual core)
- UART to support serial port
- MCT (Multi Core Timer)
- ADC (Analog Digital Converter)
- I2C/SPI bus
- Power domain
- PMU (Performance Monitoring Unit)
- MSHC (Mobile Storage Host Controller)
- PWM (Pluse Width Modulation)
- AMBA bus
- sysram node for SYSRAM memory mapping
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NHyunhee Kim <hyunhee.kim@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds the mfc node to exynos5800 which uses MFCv8.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable FIMD for peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable display controller with timing information for 1080p
panel in Exynos5800 peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable hdmi for peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds support for google peach-pi board having the
Exynos5800 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Most of the nodes of exynos5420 remains same for exynos5800.
So the exynos5420.dtsi is included in exynos5800 and the changed
node properties will be overriden.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch adds the dts file for xyref5260 board which
is based on exynos5260 SoC.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch adds the dts files for exynos5260.
Signed-off-by: NPankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Made it as per DT node naming convention <name@reg_addr>.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Key code macros improve readability on exnos4210-origen,
exynos4412-origen and exynos5250-arndale boards.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
[kgene.kim@samsung.com: squashed similar two patches]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enabled RTC and WDT nodes on exynos4210-origen and
exynos4412-origen boards.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
[kgene.kim@samsung.com: squashed similar two patches]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.  Along with this change, we can delete l2x0.c
from prima2.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add device-tree file for APQ8084-MTP board, which belongs
to the Snapdragon 805 family.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add support for the Qualcomm Snapdragon 805 APQ8084 SoC. It is
used on APQ8084-MTP and other boards.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add basic APQ8064 SoC include device tree and support for basic booting on
the IFC6410 board.  Also, keep dtb build list and qcom_dt_match in sorted
order.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-msm8660-surf.dts)
* Cleanup cpu node to match binding spec, enable-method and compatible
  should be per cpu, not part of the container
* Add GSBI node and configuration of GSBI controller
Signed-off-by: NKumar Gala <galak@codeaurora.org>