This patch removes registration helpers and support files,
used for non-DT i.MX1 targets.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Synertronixx SCB9328 board is very similar to Armadeus APF9328,
so it can be easily reimplemented in DT way.
This patch removes support for non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

mach-apf9328.c can be replaced with devicetree equivalent: imx1-apf9328.dts,
so remove the board file.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The imx31 and imx35 idle functions are almost the same, but we
currently have to check the cpu type every time. This can be
simplified by moving the logic from mx3_cpu_lp_set() into
two separate idle functions, removing the last user of
cpu_is_mx35.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Tested basic suspend/resume on a mx25pdk:

$ echo enabled > /sys/class/tty/ttymxc0/power/wakeup
$ echo mem > /sys/power/state

Then press any key in the serial console and the system wakes up.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.MX6UL is a new SOC, add MSL support
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

After the cleanup on imx timer driver, now it's ready to be moved into
drivers/clocksource/.  Let's do it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

In order to save power the DDR pins should be put into high
impedance when in suspend to RAM.

This requires manually requesting self refresh (rather than using the
automatic mode implemented by the CCM / ESDCTL), followed by
reconfiguring the IOMUXC.

Of course the code to do this cannot itself run from DDR so the
code is copied to and executed from internal memory.

In my tests using a custom i.MX53 board with LPDDR2 RAM
this reduced the suspend power consumption from 200mW to 60mW.
Signed-off-by: NMartin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add i.MX7D MSL support.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk.  Let's move them into drivers/clk/imx folder.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>

eukrea_mbimxsd35 board has device tree support, so we can get rid of the
board related files.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

We use dynamic memory mapping when using dt, so remove all the static mappings.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

As mx25 is a dt-only platform, we can get rid of platform code support files,
which are unused now.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

As there is no more mx25 board files, we can turn mx25 into a dt-only platform.

Rename imx25-dt.c to mach-imx25.c to be consistent with the other i.MX SoCs.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

eukrea mx25 is well supported in device tree, so let's get rid of its board
files.

Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx25-pdk.dts provides a more complete support than the board file version, so
let's get rid of the board file.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch introduces an independent cpuidle driver for
i.MX6SX, and supports arm power off in idle, totally
3 levels of cpuidle are supported as below:

1. ARM WFI;
2. SOC in WAIT mode;
3. SOC in WAIT mode + ARM power off.

ARM power off can save at least 5mW power.

This patch also replaces imx6q_enable_rbc with imx6_enable_rbc.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.

While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

There are a couple of gate clocks are mutually exclusive on i.MX6, i.e.
LVDSCLK1_IBEN and LVDSCLK1_OBEN.  They cannot be enabled simultaneously.
This patches adds an exclusive gate clock type specifically for such
case.  The clock driver will need to call imx_clk_gate_exclusive() to
register a gate clock with parameter exclusive_mask indicating the mask
of gate bits which are mutually exclusive to this gate clock.

Right now, it only handles the exclusive gate clocks which are defined
in a single hardware register, which is the case we're running into
today.  But it can be extended to handle exclusive gate clocks defined
in different registers later if needed.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds basic devicetree support for i.MX1 based SoCs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

All the current support of mach-mxt_td60 board can be converted to devicetree.

Remove the board file.

Cc: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

mx1ads.c can be replaced with devicetree equivalent: imx1-ads.dts,
so remove the board file.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

pcm970-baseboard.c and mach-pcm038.c can be replaced with their
devicetree equivalents: imx27-phytec-phycore-rdk.dts and
imx27-phytec-phycore-som.dtsi respectively, so remove the board files.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their
devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and
imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

My earlier patch 1fc593fe ("ARM: imx: build i.MX6 functions
only when needed") fixed a problem with building an i.MX5 kernel,
but now the problem has returned for the case where we allow
ARMv6K SMP builds in multiplatform. With CONFIG_CPU_V7 disabled,
but i.MX3 and SMP enabled, we get this build error:

arch/arm/mach-imx/built-in.o: In function `v7_secondary_startup':
:(.text+0x5124): undefined reference to `v7_invalidate_l1'

This puts the code inside of an "ifdef CONFIG_SOC_IMX6" to hopefully
do the right thing in all configurations.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

i.MX1 camera driver has been removed by the commit 90b05589.
This patch removes remaining support files for this camera.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:

arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
 undefined reference to `imx6q_cpuidle_init'

This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board. However, the
support may be added in the future by using the devicetree.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The only code left in mm-imx5.c is to create static mapping.  While all
IMX platform code are moved to use dynamic mapping, the file can just be
removed now.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since i.MX51 becomes a DT only platform, those non-DT support files can
be removed now.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since i.MX51 becomes DT only now, we can drop option MACH_IMX51_DT and
just use SOC_IMX51 instead.  While at it, rename imx51-dt.c to
mach-imx51.c to align with the name schema of other IMX DT only
platforms.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add basic suppport for i.MX6 SoloX SoC.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

eukrea_mbimxsd51-baseboard.c and mach-cpuimx51sd.c can be replaced with their
devicetree equivalents: imx51-eukrea-mbimxsd51-baseboard.dts and
imx51-eukrea-cpuimx51.dtsi respectively, so remove the board files.

This allows the conversion of mx51 to a devicetree-only platform.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The device tree version for the babbage board (imx51-babbage.dtb) has a more
complete support than the board file version, so remove the board file source
code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Even when CONFIG_SUSPEND is enabled, it makes no sense to build
suspend-imx6.o if none of i.MX6 support is built in.  Let's build
suspend-imx6.o only when both CONFIG_SUSPEND and CONFIG_SOC_IMX6 are
enabled.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The pm-imx6q.c works for all i.MX6 SoCs, so let's rename it to pm-imx6.c
and have the build controlled by option CONFIG_SOC_IMX6.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With v7_cpu_resume() being moved out of headsmp.S, all the remaining
code in the file is only needed by CONFIG_SMP build.  So we can control
the build of headsmp.o with only obj-$(CONFIG_SMP) now.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>