Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.

This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.

dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: NRicardo Neri <ricardo.neri@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.

So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.

Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.

Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.

Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.

Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add support to dump the HDMI wrapper, core, PLL and PHY registers
through debugfs.
Signed-off-by: NMythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implement detect() by checking the hot plug detect status.

The implementation is not very good, as it always turns on the HDMI
output to get the detection working. HDMI driver needs improvements so
that we could enable only core parts of it.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current driver had a hardcoded minimum value of 2 for pixel clock
divisor (PCD). This doesn't seem to be right.

OMAP4 TRM says that PCD can be 1 when not downscaling, and inverted
pixel clock (IPC) is off.

OMAP3 TRM says the same, but also in the register descriptions that PCD
value 1 is invalid.

OMAP2 TRM says PCD 2 is the minimum.

OMAP2 is still untested, but for both OMAP3 and OMAP4 PCD of 1 seems to
work fine.

This patch adds a new DSS feature, FEAT_PARAM_DSS_PCD, which is used to
find the minimum and maximum PCD. The minimum is set to 2 for OMAP2, and
1 for OMAP3/4.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI IP fundamentally has replaceable core PHY and PLL blocks.
These blocks might vary across OMAP's but the end functionality such as to
enable or disable PLL, PHY, function to read EDID would remain the same.

Thus to make the current hdmi DSS driver compatible with different OMAP's having
different IP blocks( A combination of different core, PHY, PLL blocks), function
pointer approach is introduced.

With function pointer, relevant IP dependent functions are mapped to the generic
functions used by DSS during the initialization based on the OMAP compiled.
Thus making hdmi DSS driver IP agnostic.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.

Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Add support to define overlay capabilities into dss_features. The
features are set to overlay->caps at initialization time.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

The DMA FIFO threshold registers and burst size registers have changed
for OMAP4.  The current code only handles OMAP2/3 case, and so the
values are a bit off for OMAP4.  A summary of the differences between
OMAP2/3 and OMAP4:

Burst size:
OMAP2/3: 4 x 32 bits / 8 x 32 bits / 16 x 32 bits
OMAP4: 2 x 128 bits / 4 x 128 bits / 8 x 128 bits

Threshold size:
OMAP2/3: in bytes (8 bit units)
OMAP4: in 128bit units

This patch fixes the issue by creating two new helper functions in
dss_features: dss_feat_get_buffer_size_unit() and
dss_feat_get_burst_size_unit(). These return (in bytes) the unit size
for threshold registers and unit size for burst size register,
respectively, and are used to calculate correct values.

For the threshold size the usage is straightforward. However, the burst
size register has different multipliers for OMAP2/3 and OMAP4. This
patch solves the problem by defining the multipliers for the burst size
as 2x, 4x and 8x, which fit fine for the OMAP4 burst size definition
(i.e. burst size unit for OMAP4 is 128bits), but requires a slight twist
on OMAP2/3 by defining the burst size unit as 64bit.

As the driver in practice always uses the maximum burst size, and no use
case currently exists where we would want to use a smaller burst size,
this patch changes the driver to hardcode the burst size when
initializing DISPC. This makes the threshold configuration code somewhat
simpler.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP2 doesn't have CPR, PRELOAD nor FIR_COEF_V registers. Add new
feature definitions for those, and check the feature before accessing
those registers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3430 requires an 96MHz clock to VENC's DAC, but no other OMAP needs
it.

Add a new feature, FEAT_VENC_REQUIRES_TV_DAC_CLK, which tells if the
clock is needed on this platform, and use that feature in venc.c to
decide if the clock needs enabling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add new registers specific to UV color component that are introduced in OMAP4.
Add simple helper functions to configure the newly added registers.
These new registers are mainly:
- UV base address registers used specifically for NV12 color-format
- FIR registers used for UV-color-component scaling on OMAP4
- Accumulator registers used for UV-color-component scaling
Add these new registers to save/restore and DUMPREG functions.
Also add two new features for OMAP4:
- FEAT_HANDLE_UV_SEPARATE - this is used on OMAP4 as UV color-component requires
  separate handling.
- FEAT_ATTR2 - this is used on OMAP4 to configure new ATTRIBUTES2 register.
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16,
ARGB16_1555, XRGB16_1555.
NV12 color format is defined here, its support in DSS will be added separately.
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

CTS and N parameters are used to regenerate the audio clock from
the TMDS clock at the HDMI sink. In  OMAP4430 ES1.0 version
the calculation of the CTS parameter is done by the HDMI IP
(hardware mode) while in others it must be done by the HDMI driver
(software mode). A DSS feature is used to indicate the HDMI
driver which mode is used.
Signed-off-by: NRicardo Neri <ricardo.neri@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Create a separate DSS features structure for OMAP4430 ES1.0. This
structure is used to expose features only present in such
silicon version. Specifically, this is required to handle how
the HDMI IP calculates the CTS parameter for audio clock
regeneration packets. OMAP4430 ES1.0 is the only one that supports
computation of the CTS parameter by the HDMI IP (hardware mode).
The rest of the revisions require the HDMI driver to perform the
computation.
Signed-off-by: NRicardo Neri <ricardo.neri@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On OMAP3, the DSI module has 2 data lanes. On OMAP4, DSI1 has 4 data lanes
and DSI2 has 2 data lanes. Introduce function dsi_get_num_data_lanes() which
returns the number of data lanes on the dsi interface, introduce function
dsi_get_num_data_lanes_dssdev() which returns the number of data lanes used by
the omap_dss_device connected to the lanes.

Use the DSI_GNQ register on OMAP4 to get the number of data lanes, modify
dsi.c to use the number of lanes and the extra data lanes on DSI1.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol
engine and DISPC Functional clock. Do the following:

- Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the
  dsi module number as an argument.
- Create debugfs files for dsi2, split the corresponding debugfs functions.
- Allow DPI to use these new clock sources.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_dss_features definitions were missing consts.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3430 has RESETDONETXCLKESCx bits in the order following bitnumber
order for lanes 0, 1, 2: 28, 27, 26. OMAP3630 and later have them in
saner order: 24, 25, 26 (and 27, 28 for OMAP4).

This patch adds a dss_feature that can be used to differentiate between
those two orders of RESETDONETXCLKESCx bits.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

CIO LDO status check seems to be broken on OMAP3630+ chips, and it's
also quite unclear what LDO status actually tells and when its status
changes.

This patch removes the whole check on the grounds that if there's a
problem with the LDO, we should anyway catch the problem as we check the
CIO power state and CIO reset status.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The following changes have changed from OMAP3 to OMAP4 DSI:
-The register field DSI_PLL_FREQSEL in DSI_PLL_CONFIGURATION2 has been removed.
-DCS_CMD_ENABLE and DCS_CMD_CODE bits have been moved from DSI_CTRL to
DSI_VC_CTRLi, hence the control of the bits is available per VC.
-DSI LDO powergood notification doesn't work on OMAP4. This is mentioned in
OMAP4 errata revision 1.8(Errata 1.76).
-OCP_WIDTH register field is included in DSI_VC_CTRL.
-The SCP clock is also required to access DSI PLL registers

Introduce dss features for these changes so that DSI runs on both OMAP3 and
OMAP4.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.

This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.

This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSI PLL parameters (regm, regn, regm_dispc, regm_dsi, fint) have different
fields and also different Max values on OMAP3 and OMAP4. Use dss features to
calculate the register fields and min/max values based on current OMAP revision.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Create 2 functions dss_feat_get_param_min() and dss_feat_get_param_max() which
return the minimum and maximum value of a parameter. Introduce a enum in
dss_features called dss_range_param which contains parameters whose ranges we
are interested in.

Replace this with dss_feat_get_max_dss_fck() which is specific to the parameter
DSS_FCK.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The structures dss_reg_field and dss_clk_source_name have enum members which
specify the register field and the clock source respectively. These members are
not used to choose the correct result in the corresponding feature functions.
Remove these members and change the features array declaration to incorporate
these enums.

The structure dss_clk_source_name without the enum member is just a pointer to
an string. Remove the structure and use a character pointer directly.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On OMAP3, the pixel clock for the LCD manager was derived through DISPC_FCLK as:

Lcd Pixel clock = DISPC_FCLK / lcd / pcd

Where lcd and pcd are divisors in the DISPC_DIVISOR register.

On OMAP4, the pixel clocks for LCD1 and LCD2 managers are derived from 2 new
clocks named LCD1_CLK and LCD2_CLK. The pixel clocks are calculated as:

Lcd_o Pixel clock = LCDo_CLK / lcdo /pcdo, o = 1, 2

Where lcdo and pcdo registers are divisors in DISPC_DIVISORo registers.

LCD1_CLK and LCD2_CLK can have DSS_FCLK, and the M4 divider clocks of DSI1 PLL
and DSI2 PLL as clock sources respectively. Introduce functions to select and
get the clock source for these new clocks. Modify DISPC functions get the
correct lck and pck rates based on the clock source of these clocks. Since
OMAP2/3 don't have these clocks, force OMAP2/3 to always have the LCD_CLK source
as DSS_CLK_SRC_FCK by introducing a dss feature.

Introduce clock source names for OMAP4 and some register field changes in
DSS_CTRL on OMAP4.

Currently, LCD2_CLK can only have DSS_FCLK as its clock source as DSI2 PLL
functionality hasn't been introduced yet. BUG for now if DSI2 PLL is selected as
clock.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In OMAP3xxx DISPC_DIVISOR register has a logical clock divisor (lcd_div)
field. The lcd_div is common, for deciding the DISPC core functional clock
frequency, and the final pixel clock frequency for LCD display.

In OMAP4, there are 2 LCD channels, hence two divisor registers, DISPC_DIVISOR1
and DISPC_DIVISOR2. Also, there is a third register DISPC_DIVISOR.

The DISPC_DIVISOR in OMAP4 is used to configure lcd_div exclusively for core
functional clock configuration. For pixel clock configuration of primary and
secondary LCDs, lcd_div of DISPC_DIVISOR1 and DISPC_DIVISOR2 are used
respectively
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NRaghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clock source names vary across OMAP2/3 and OMAP4, the clock source enum
names have been made generic in the driver, but for purposes of debugging
and dumping clock sources, it is better to preserve the actual TRM name of
the clock.

Introduce a dss feature function 'dss_feat_get_clk_source_name()' which
returns a string with the TRM clock name for the current OMAP in use. The OMAP
specific name is printed along the generic name within brackets.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The maximum supported frequency for DSS has increased from 173 to 186 Mhz on
OMAP4.

Introduce a dss feature function to get the max_fck to replace DISPC_MAX_FCK
macro.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dss_features and register fields to incorporate changes in DISPC pipelines
between OMAP3 and OMAP4.

Register fields added: FEAT_REG_HORIZONTALACCU, FEAT_REG_VERTICALACCU
DSS Features added: FEAT_LINEBUFFERSPLIT, FEAT_ROWREPEATENABLE, FEAT_RESIZECONF

_dispc_set_scaling() and _dispc_set_rotation_attrs() have been cleaned up.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP2 doesn't support SDI or DSI. Remove them from
omap2_dss_supported_displays.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>