Functions such as is_valid_ether_addr() expect u8 *, so use that
instead of char *.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We allocate efx_channel structures with kzalloc() so we don't need to
zero-initialise individual fields in efx_probe_channel().  Further,
this function will be called again during DMA ring resizing and we
should not reset any statistics then.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EF10 implements option descriptors to switch TX checksum offload
on and off between packets.  We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These DMA descriptor types will only be used by the userland
networking stack.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN
will be defined as 0, so this macro is redundant.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is substantial latency in generation and handling of PPS events
from the NIC, which we have to correct for before passing a host
timestamp to the PPS subsystem.  We compare clocks with the MC,
giving us two offsets to subtract from the timestamp generated by
pps_get_ts():

(a) Time from the last good sync (where we got host and NIC timestamps
    for nearly the same instant) to the time we called pps_get_ts()
(b) Time from NIC top of second to the last good sync

We currently calculate (a) + (b) in a quite confusing way.
Instead, calculate (a) completely, then add (b) to it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use conventional net_ratelimit() instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: NJohn Greene <jogreene@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLiu Junliang <liujunliang_ljl@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove occurrences of unused struct __vxge_hw_device pointer in functions
vxge_learn_mac() and vxge_rem_isr().

Detected by Coverity: CID 139839, CID 139842.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver description files give these descriptions to the vendor specific
ports on this modem:

 VID_19D2&PID_1270&MI_00: "ZTE MF667 Diagnostics Port"
 VID_19D2&PID_1270&MI_01: "ZTE MF667 AT Port"
 VID_19D2&PID_1270&MI_02: "ZTE MF667 ATExt2 Port"
 VID_19D2&PID_1270&MI_03: "ZTE MF667 ATExt Port"
 VID_19D2&PID_1270&MI_04: "ZTE MF667 USB Modem"
 VID_19D2&PID_1270&MI_05: "ZTE MF667 Network Adapter"
Signed-off-by: NRaymond Wanyoike <raymond.wanyoike@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused network device private data pointer 'vp' in function
vortex_eisa_cleanup(). Detected by Coverity: CID 139826.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove occurrences of unused pointer to network device private data in
functions dlci_header() and dlci_receive().

Detected by Coverity: CID 139844, CID 139845.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ee45fd92 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:

drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used

Stick the label inside the same #ifdef that the code which calls
it uses.  Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.

Cc: Jon Cooper <jcooper@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems like this function was intended to have special handling for
urb statuses of -ENOENT and -ECONNRESET.  But now it just prints some
debugging and returns at the start of the function.

I have removed the dead code, it's still in the git history if anyone
wants to revive it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.

Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x driver uses incorrect PF identifier to configure (in HW) the VF
interrupt scheme; As a result, in multi-function mode the configuration
for PFs with a high index (4+) will overflow and the PF will erroneously
configure a single ISR scheme for its VFs.
As a result, if such a VF uses multiple queues, interrupt generation will
stop after VF receives an Rx packet or sends a Tx packet on a queue
other than queue[0].
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together.  When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared.  This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.

netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."

tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: NDavid Vrabel <david.vrabel@citrix.com>
Tested-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.

My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here.  And really the original
code is confusing to look at.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.

This patch has been compile tested.
Signed-off-by: NJames M Leddy <james.leddy@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes old and unsupported CLPS711X IrDA driver.
Support for IrDA for CLPS711X serial port now provided by commit
4a33f1f59abd (serial: clps711x: Add support for N_IRDA line
discipline), so IrDA-mode can be turned ON with "irattach" tool
through "irtty" driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Orignal code will not detect a DMA mapping failure, causing the HW
to attempt a DMA from an invalid address.

This patch add the error check and eventually simply drops the TX
packet if we can't map it for DMA.
Signed-off-by: Nandrea merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In original code the old RX DMA buffer is unmapped and processed and at the end
of the isr a new buffer is mapped with pci_map_single and attached to the RX
descriptor.

If pci_map_single fails then the RX descriptor remains with no valid DMA buffer
attached.
In this condition the DMA will target where it shouldn't with obvious evil
consequences.

Simply avoiding re-arming the descriptor will prevent buggy DMA but it will
result soon in RX stuck.

This patch move the DMA mapping of the new buffer at the beginning of the ISR
(and it adds error check for pci_map_single success/fail).

If the DMA mapping fails then we do not unmap the old buffer and we re-arm the
descriptor without processing it, with the old DMA buffer still attached.

In this way we lose the currently RX-ed packet, but whenever next calls to
pci_map_single will succeed again,then the RX process will go on without stuck.
Signed-off-by: Nandrea merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent patch to fix receive side flow control
(11b57f90: xen-netback: stop vif thread
spinning if frontend is unresponsive) solved the spinning thread problem,
however caused an another one. The receive side can stall, if:
- [THREAD] xenvif_rx_action sets rx_queue_stopped to true
- [INTERRUPT] interrupt happens, and sets rx_event to true
- [THREAD] then xenvif_kthread sets rx_event to false
- [THREAD] rx_work_todo doesn't return true anymore

Also, if interrupt sent but there is still no room in the ring, it take quite a
long time until xenvif_rx_action realize it. This patch ditch that two variable,
and rework rx_work_todo. If the thread finds it can't fit more skb's into the
ring, it saves the last slot estimation into rx_last_skb_slots, otherwise it's
kept as 0. Then rx_work_todo will check if:
- there is something to send to the ring (like before)
- there is space for the topmost packet in the queue

I think that's more natural and optimal thing to test than two bool which are
set somewhere else.
Signed-off-by: NZoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED.  If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.

So, treat an unexpected backend CLOSED state the same as CLOSING.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device was mentioned in an OpenWRT forum.  Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
 0: qcdm
 2: nmea
 3: modem
 8: qmi
 9: storage
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.

The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.

This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
Reported-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The trigger and events functionality can be useful even if packet
timestamping is not used, but the required PTP clock is only enabled
when packet timestamping is started. This patch moves the clock enable
to when the interface is configured.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the external timestamping code is hardcoded to use the
rising edge even though the hardware has configurable event edge
detection. This patch changes the code to use falling edge detection
if PTP_FALLING_EDGE is set in the user supplied flags.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the SKBTX_IN_PROGRESS bit in tx_flags dp83640_txtstamp when doing
tx timestamps as per Documentation/networking/timestamping.txt.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fail_over_mac could be set to active or follow in any time for all modes,
so if the fail_over_mac is not none and the current mode is not active-backup,
the bond_set_mac_address() could not change the master and slave's MAC address.

In bond_set_mac_address(), the fail_over_mac should only affect AB mode, so modify
to check the mode in addition to fail_over_mac when setting bond's MAC address.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to bonding.txt, the fail_over_ma should only affect active-backup mode,
but I found that the fail_over_mac could be set to active or follow in all
modes, this will cause new slave could not be set to bond's MAC address at
enslave processing and restore its own MAC address at removal processing.

The correct way to fix the problem is that we should not add restrictions when
setting options, just need to modify the bond enslave and removal processing
to check the mode in addition to fail_over_mac when setting a slave's MAC during
enslavement. The change active slave processing already only calls the fail_over_mac
function when in active-backup mode.

Thanks for Jay's suggestion.

The patch also modify the pr_warning() to pr_warn().

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>