This ports Herbert Xu's "maybe_stop_tx" code and removes the tx_lock
which is not needed.
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

After testing we confirmed that the irq_sem can safely be
removed from ixgbe.

Add strict state checking code to various ethtool parts to
properly protect against races between various driver reset
paths.
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Changes in other networking paths uncovered a bug in the xircom_cb
driver which made the kernel spew lots of the following error messages:

  BUG eth1 code -5 qlen 0

It turned out that the driver returned -EIO when there was no
descriptor available for sending packets. It should return
NETDEV_TX_BUSY instead. This was discussed on the netdev list before,
see http://thread.gmane.org/gmane.linux.network/84603 .
Signed-off-by: NErik Mouw <mouw@nl.linux.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a check for the pci_register_driver() return value.  Removed unused
variable pad_allocated.

The aim of this patch is to remove the following warning messages:
drivers/net/tlan.c: In function 'tlan_probe':
drivers/net/tlan.c:486: warning: ignoring return value of 'pci_register_driver', declared with attribute warn_unused_result
Signed-off-by: NLeonardo Potenza <lpotenza@inwind.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Marvell Orion system on chips have an integrated mv643xx MAC.  On these
little endian ARM devices mv643xx will oops when checksum offload is
enabled.  Swapping the byte order of the protocol and checksum solves this
problem.
Signed-off-by: NByron Bradley <byron.bbradley@gmail.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Manish Lachwani <mlachwani@mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon FE chip has a ram buffer therefore it needs the alignment
restriction and hang check workarounds.

Therefore:
  * Autodetect the prescence/absence of ram buffer
  * Rename the flag value to reflect this
  * Use it consistently (ie don't reread register)
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

WARNING: vmlinux.o(.text+0x25dca0): Section mismatch in reference from the function .veth_probe() to the function .init.text:.veth_probe_one()
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It is done in order to improve performance.
Signed-off-by: NDor Laor <dor.laor@qumranet.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This fixes a potential dangling xmit problem.

We also suppress refill interrupts until we need them.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Fix bug found by Christian Borntraeger: if the other side fills all
the registered network buffers before we enable NAPI, we will never
get an interrupt.  The simplest fix is to process the input queue once
on open.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Hello Rusty,

virtnet_probe already calls alloc_etherdev, which calls ether_setup.
There is no need to do that again.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This patch moves virtio under the virtualization menu and changes virtio
devices to not claim to only be for lguest.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

A reset function solves three problems:

1) It allows us to renegotiate features, eg. if we want to upgrade a
   guest driver without rebooting the guest.

2) It gives us a clean way of shutting down virtqueues: after a reset,
   we know that the buffers won't be used by the host, and

3) It helps the guest recover from messed-up drivers.

So we remove the ->shutdown hook, and the only way we now remove
feature bits is via reset.

We leave it to the driver to do the reset before it deletes queues:
the balloon driver, for example, needs to chat to the host in its
remove function.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Since we want to reset the device to remove them, this is simpler
(device is reset for us on driver remove).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

1) Turn GSO on virtio net into an all-or-nothing (keep checksumming
   separate).  Having multiple bits is a pain: if you can't support something
   you should handle it in software, which is still a performance win.

2) Make VIRTIO_NET_HDR_GSO_ECN a flag in the header, so it can apply to
   IPv6 or v4.

3) Rename VIRTIO_NET_F_NO_CSUM to VIRTIO_NET_F_CSUM (ie. means we do
   checksumming).

4) Add csum and gso params to virtio_net to allow more testing.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

It's far easier to deal with packets if we don't have to parse the
packet to figure out the header length to know how much to pull into
the skb data.  Add the field to the virtio_net_hdr struct (and fix the
spaces that somehow crept in there).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

It seems that virtio_net wants to disable callbacks (interrupts) before
calling netif_rx_schedule(), so we can't use the return value to do so.

Rename "restart" to "cb_enable" and introduce "cb_disable" hook: callback
now returns void, rather than a boolean.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Previously we used a type/len pair within the config space, but this
seems overkill.  We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.

The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Use it in virtio_net (replacing buggy version there), it's also going
to be used by TAP for partial csum support.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Signed-off-by: NPaulius Zaleckas <pauliusz@yahoo.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Signed-off-by: NKalle Pokki <kalle.pokki@eke.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It prevents overwritting new data from DMA.
Signed-off-by: NAlexey Demin <bf53x@ya.ru>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch puts phy in power-down mode when interface is down.
Also we should think about energy detect power-down mode, that will
decrease power consumption when no link.
Signed-off-by: NVitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EMAC driver: use simpler comment headers and strip out information that is maintained in the scm's log
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bf537 Ethernet MAC driver in the 2007R1.1-RC3 kernel (and the
current kernel) do not implement multicast hash filtering. This
is a performance problem if you have lots of multicast on your network.

This patch plugs the right bits into the multicast hash registers.
Signed-off-by: NAidan Williams <aidan@nicta.com.au>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix PCI table section type conflict, by removing __devinitdata.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables config mode access after clearing PCI settings.
Some BIOS's seem to not do WOL if config bit still set.

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=9721Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the sky2 deadman timer forces a recovery, the multicast hash
list is lost. Move the call to sky2_set_multicast to the end
of sky2_up() so all paths that bring device up will restore multicast.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pci-skeleton.c has several problems with compilation, such as missing args
when calling synchronize_irq(). Fix it.
Signed-off-by: NJike Song <albcamus@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this PHY present on the MPC8315E and MPC837xE RDB boards.
Signed-off-by: NJohnson Leung <r58129@freescale.com>
Signed-off-by: NKevin Lam <r43770@freescale.com>
Signed-off-by: NJoe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation regarding synchronisation at the head of the natsemi
driver was badly bitrotted so replace it with a general statement about
the techniques used which is less likely to bitrot.

Also remove the note saying these chips are uncommon - it makes little
difference but they were used in a number of laptops and at least one mass
market PCI ethernet card.
Signed-off-by: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY read/write functions can potentially sleep (e.g., a PHY accessed
via I2C).  The following changes were made to account for this:

    * Change spin locks to mutex locks
    * Add a BUG_ON() to phy_read() phy_write() to warn against
      calling them from an interrupt context.
    * Use work queue for PHY state machine handling since
      it can potentially sleep
    * Change phydev lock from spinlock to mutex
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a critical fix for MCP77 and MCP79 devices. The feature
flags were missing the define for correct mac address
(DEV_HAS_CORRECT_MACADDR).
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the case where no multicast addresses are requested to
be added to the multicast filter. The multicast mask must be set to all
1's instead of all 0's.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the tx pause enable watermark flags. The new values
where determined to be optimal during testing.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>