- 26 9月, 2013 37 次提交
-
-
由 Sachin Kamat 提交于
devm_request_and_ioremap() is deprecated. Use devm_ioremap_resource() instead. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jackey Shen 提交于
Clean up the duplicate macros: mmc_sd_card_uhs -> mmc_card_uhs mmc_sd_card_set_uhs -> mmc_card_set_uhs Signed-off-by: NJackey Shen <jackey.shen@amd.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rodolfo Giometti 提交于
In some cases, a NULL pointer dereference happens because data is NULL when STATE_END_REQUEST case is reached in atmci_tasklet_func. Cc: <stable@vger.kernel.org> # 3.9+ Signed-off-by: NRodolfo Giometti <giometti@enneenne.com> Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
When a software timeout occurs, the transfer is not stopped. In DMA case, it causes DMA channel to be stuck because the transfer is still active causing following transfers to be queued but not computed. Cc: <stable@vger.kernel.org> # 3.9+ Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Reported-by: NAlexander Morozov <etesial@gmail.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
While speed mode is changed, CMD13 cannot be guaranteed. According to the spec., it is not recommended to use CMD13 to check the busy completion of the timing change. If CMD13 is used in this case, CRC error must be ignored. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Acked-by: NUlf Hansson <ulf.hansson@linaro.org> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
In IDMAC mode EVENT_XFER_COMPLETE is set when RI/TI of last descriptor is done. So if errors are happened in the middle of data transfers, 'dw_mci_stop_dma' during error handing can be called and eventually prevents this flag to be set. This results in permanent wait for EVENT_XFER_COMPLETE in 'dw_mci_tasklet_func'. Therefore, if dma running is stopped forcibly, EVENT_XFER_COMPLETE should be set. Reported-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NDoug Anderson <dianders@chromium.org> Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
First, compiling warning along with previous change is removed. [drivers/mmc/host/dw_mmc.c:1890:7: warning: unused variable 'ctrl'] And with the recommendation in manual, IDMAC software reset is followed by dma-reset of the CTRL register in order to terminate the transfer. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
There are three resets in CTRL register. FIFO reset is especially used in several points with the same routine. It could be replaced with one function and the others may be applied similarly if needed. So, mci_wait_reset() is modified to allow various bit field of reset. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Main change corresponds to dw_mci_command_complete(). And EBE is divided into read and write. Some minor changes for code readability. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
In error cases, DTO interrupt may or may not be generated depending on remained data. Stop/Abort command ensures DTO generation for that situation. Currently if 'stop' field of data is empty, there is no stop/abort command. So, it could hang waiting DTO. This change reinforces these cases. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Even if response error is detected in case data command, data transfer is continued. It means that data can live in FIFO. Current handling just breaks out the request when seeing the command error. This causes kernel panic in dw_mci_read_data_pio() [host->data = NULL]. And also, FIFO should be guaranteed to be empty. Unable to handle kernel NULL pointer dereference at virtual address 00000018 <...> [<c02af814>] (dw_mci_read_data_pio+0x68/0x198) from [<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0) [<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0) from [<c006b094>] (handle_irq_event_percpu+0x50/0x194) [<c006b094>] (handle_irq_event_percpu+0x50/0x194) from [<c006b214>] (handle_irq_event+0x3c/0x5c) [<c006b214>] (handle_irq_event+0x3c/0x5c) from [<c006de1c>] (handle_fasteoi_irq+0xa4/0x148) [<c006de1c>] (handle_fasteoi_irq+0xa4/0x148) from [<c006aa88>] (generic_handle_irq+0x20/0x30) [<c006aa88>] (generic_handle_irq+0x20/0x30) from [<c000f154>] (handle_IRQ+0x38/0x90) [<c000f154>] (handle_IRQ+0x38/0x90) from [<c00085bc>] (gic_handle_irq+0x34/0x68) [<c00085bc>] (gic_handle_irq+0x34/0x68) from [<c0011f40>] (__irq_svc+0x40/0x70) Exception stack(0xef0b1c00 to 0xef0b1c48) 1c00: 000eb0cf ffffffff 00001300 c01a7738 ef295e10 0000000a c04df298 ef0b1dc0 1c20: ef295ec0 00000000 00000000 00000006 00000000 ef0b1c48 c02b1274 c01a7764 1c40: 20000113 ffffffff [<c0011f40>] (__irq_svc+0x40/0x70) from [<c01a7764>] (__loop_delay+0x0/0xc) Code: e1a00005 e0891006 e0662004 e12fff33 (e59a3018) ---[ end trace a7043b9ba9aed1db ]--- Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Card Read Threshold should be ensured that the card clock does not stop in the middle of a block of data being transferred from the card to the Host. Specially, clock stop is allowed in fast transfer such as HS200 or SDR104 mode. And so, it should be enabled. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
This change helps to choose msize, rx_watermark and tx_watermark depending on block size for IDMAC mode. For SDIO block size can be variable, so if these values are set incorrectly, card clock may stop. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Both f_max and f_min will be informed for core layer to request valid clock rate. But current setting from 'host->bus_hz' may not represent the max/min frequency properly. Even if host can actually support high speed than bus_hz, core layer will not request clock rate over bus_hz. Basically, f_max/f_min can be set with the values according to spec. And then host will make its best effort to meet the rate. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
'supports-highspeed' is not one of the quirks but is a capability. So, it's removed from quirks. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
As host controller can support eMMC's HS200 mode at 1.8V or 1.2V, these capability will be added. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Exynos's host has divider logic before 'cclk_in' to controller core. It means that actual clock rate of ciu clock comes from this divider value. So, source clock should be adjusted along with 'ciu_div' which indicates the host's divider ratio. Setting clock rate basically fits the required speed. Specially, 'cclk_in' should have double rate of target speed in case of DDR 8-bit mode. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
Implements variable delay tuning. In this change, exynos host can determine the correct sampling point for the HS200 and SDR104 speed mode. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
For the speed modes HS200 and SDR104, tuning is needed to determine the correct sampling point. Actual tuning procedure is provided by specific host controller driver. This patch defines the tuning command and tuning data. Additionally, 'struct dw_mci_slot' is moved to header file to consider the extensive usages in driver. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Yuvaraj Kumar C D 提交于
Exynos5420 Mobile Storage Host controller has Security Management Unit (SMU) for channel 0 and channel 1 (mainly for eMMC). This time, SMU configuration is set for non-encryption mode. Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Yuvaraj Kumar C D 提交于
Current platform specific private data initialization call dw_mci_exynos_priv_init() can be used to do platform specific initialization of SMU and others in future. So the drv_data->init call has moved to dw_mci_probe(). Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Yuvaraj Kumar C D 提交于
Currently platform specific private data initialization is done by dw_mci_socfpga_priv_init and dw_mci_socfpga_parse_dt. As we already have separate platform specific device tree parser dw_mci_socfpga_parse_dt, move the dw_mci_socfpga_priv_init code to dw_mci_socfpga_parse_dt. We can use the dw_mci_socfpga_priv_init to do some actual platform specific initialization. Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Yuvaraj Kumar C D 提交于
Currently platform specific private data initialization is done by dw_mci_exynos_priv_init and dw_mci_exynos_parse_dt. As we already have separate platform specific device tree parser dw_mci_exynos_parse_dt, move the dw_mci_exynos_priv_init code to dw_mci_exynos_parse_dt. We can use the dw_mci_exynos_priv_init to do some actual platform specific initialization of SMU and etc. Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Doug Anderson 提交于
The TMOUT register is set to 0xffffffff at probe time but isn't set after suspend/resume. Add an init of this value. No problems were observed without this (it will also be set in __dw_mci_start_request if there is data to send), but it makes the register dump before and after suspend cleaner. Signed-off-by: NDoug Anderson <dianders@chromium.org> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Reviewed-by: NTomasz Figa <t.figa@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Doug Anderson 提交于
Previously the dw_mmc driver would ignore any requests to disable the card's clock. This doesn't seem like a good thing in general, but had one extra bad side effect in the following situation: * mmc core would set clk to 400kHz at boot time while scanning * mmc core would set clk to 0 since no card, but it would be ignored. * suspend to ram and resume; clocks in the dw_mmc IP block are now 0 but dw_mmc thinks that they're 400kHz (it ignored the set to 0). * insert card * mmc core would set clk to 400kHz which would be considered a no-op. Note that if there is no card in the slot and we do a suspend/resume cycle, we _do_ still end up with differences in a dw_mmc register dump, but the differences are clock related and we've got the clock disabled both before and after, so this should be OK. Signed-off-by: NDoug Anderson <dianders@chromium.org> Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Doug Anderson 提交于
If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up looping around forever. This has been seen to happen on exynos5420 silicon despite the fact that we haven't enabled any wakeup events due to a silicon errata. It is safe to do on all exynos variants. Signed-off-by: NDoug Anderson <dianders@chromium.org> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Doug Anderson 提交于
The MMC subsystem handles looking for a card at probe time. Queuing up our own can race with the rest of the MMC subsystem and cause problems if we get unlucky with timing. Just remove driver own detection triggering. While progressing the request from 'mmc_rescan', if 'dw_mci_work_routine_card' routine is activated, it will cancel the current request. The problem case is that 'mmc_rescan' is prior to 'dw_mci_work_routine_card' from host own. Specifically, the following message shows the detection problem in driver's probing. It would get an err -123 (-ENOMEDIUM) during probe. [ 4.216595] dwmmc_exynos 12210000.dwmmc1: Using internal DMA controller. [ 4.395935] dwmmc_exynos 12210000.dwmmc1: Version ID is 250a [ 4.401948] dwmmc_exynos 12210000.dwmmc1: DW MMC controller at irq 108, 64 bit host data width, 64 deep fifo [ 4.424430] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0) [ 4.453975] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0) [ 4.459592] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125) [ 4.484258] dwmmc_exynos 12210000.dwmmc1: 1 slots initialized [ 4.485406] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0) [ 4.487606] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0) [ 4.489794] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0) [ 4.509757] mmc1: error -123 whilst initialising SDIO card Signed-off-by: NDoug Anderson <dianders@chromium.org> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Kuninori Morimoto 提交于
afa2c940 ("sh: ecovec24: Use MMC/SDHI CD and RO GPIO") added .tmio_flags = TMIO_MMC_USE_GPIO_CD on sh_mobile_sdhi_info, but it needs <linux/mfd/tmio.h> header. This patch adds it. Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: NYusuke Goda <yusuke.goda.sx@renesas.com> Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Grant Grundler 提交于
cscope says there are no callers for mmc_try_claim_host in the kernel. No reason to keep it. Signed-off-by: NGrant Grundler <grundler@chromium.org> Acked-by: NUlf Hansson <ulf.hansson@linaro.org> Signed-off-by: NChris Ball <cjb@laptop.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip由 Linus Torvalds 提交于
Pull Xen fixes from Konrad Rzeszutek Wilk: "Bug-fixes and one update to the kernel-paramters.txt documentation. - Fix PV spinlocks triggering jump_label code bug - Remove extraneous code in the tpm front driver - Fix ballooning out of pages when non-preemptible - Fix deadlock when using a 32-bit initial domain with large amount of memory - Add xen_nopvpsin parameter to the documentation" * tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/spinlock: Document the xen_nopvspin parameter. xen/p2m: check MFN is in range before using the m2p table xen/balloon: don't alloc page while non-preemptible xen: Do not enable spinlocks before jump_label_init() has executed tpm: xen-tpmfront: Remove the locality sysfs attribute tpm: xen-tpmfront: Fix default durations
-
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm由 Linus Torvalds 提交于
Pull device-mapper fixes from Mike Snitzer: "A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error handling fixes for dm-multipath. A fix for the thin provisioning target to not expose non-zero discard limits if discards are disabled. Lastly, add two DM module parameters which allow users to tune the emergency memory reserves that DM mainatins per device -- this helps fix a long-standing issue for dm-multipath. The conservative default reserve for request-based dm-multipath devices (256) has proven problematic for users with many multipathed SCSI devices but relatively little memory. To responsibly select a smaller value users should use the new nr_bios tracepoint info (via commit 75afb352 "block: Add nr_bios to block_rq_remap tracepoint") to determine the peak number of bios their workloads create" * tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm: add reserved_bio_based_ios module parameter dm: add reserved_rq_based_ios module parameter dm: lower bio-based mempool reservation dm thin: do not expose non-zero discard limits if discards disabled dm mpath: disable WRITE SAME if it fails dm-snapshot: fix performance degradation due to small hash size dm snapshot: workaround for a false positive lockdep warning dm stats: fix possible counter corruption on 32-bit systems dm mpath: do not fail path on -ENOSPC
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linus由 Linus Torvalds 提交于
Pull MIPS fixes from Ralf Baechle: - Fix a comment - A small cleanup the main purpose of which is to work around an internal compiler error bug in certain Codesource toolchains. * git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: mm: Move some checks out of 'for' loop in DMA operations MIPS: cpu-features.h: s/MIPS53/MIPS64/
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc由 Linus Torvalds 提交于
Pull powerpc fixes from Ben Herrenschmidt: "Here are a few things for -rc2, this time it's all written by me so it can only be perfect .... right ? :) So we have the fix to call irq_enter/exit on the irq stack we've been discussing, plus a cleanup on top to remove an unused (and broken) stack limit tracking feature (well, make it 32-bit only in fact where it is used and works properly). Then we have two things that I wrote over the last couple of days and made the executive decision to include just because I can (and I'm sure you won't object .... right ?). They fix a couple of annoying and long standing "issues": - We had separate zImages for when booting via Open Firmware vs. booting via a flat device-tree, while it's trivial to make one that deals with both - We wasted a ton of cycles spinning secondary CPUs uselessly at boot instead of starting them when needed on pseries, thus contributing significantly to global warming" * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/pseries: Do not start secondaries in Open Firmware powerpc/zImage: make the "OF" wrapper support ePAPR boot powerpc: Remove ksp_limit on ppc64 powerpc/irq: Run softirqs off the top of the irq stack
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Ingo Molnar: "An EFI fix and two reboot-quirk fixes" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/reboot: Fix apparent cut-n-paste mistake in Dell reboot workaround x86/reboot: Add quirk to make Dell C6100 use reboot=pci automatically x86, efi: Don't map Boot Services on i386
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull scheduler fixes from Ingo Molnar: "Three small fixes" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/balancing: Fix cfs_rq->task_h_load calculation sched/balancing: Fix 'local->avg_load > busiest->avg_load' case in fix_small_imbalance() sched/balancing: Fix 'local->avg_load > sds->avg_load' case in calculate_imbalance()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull perf fixes from Ingo Molnar: "Assorted standalone fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Add model number for Avoton Silvermont perf: Fix capabilities bitfield compatibility in 'struct perf_event_mmap_page' perf/x86/intel/uncore: Don't use smp_processor_id() in validate_group() perf: Update ABI comment tools lib lk: Uninclude linux/magic.h in debugfs.c perf tools: Fix old GCC build error in trace-event-parse.c:parse_proc_kallsyms() perf probe: Fix finder to find lines of given function perf session: Check for SIGINT in more loops perf tools: Fix compile with libelf without get_phdrnum perf tools: Fix buildid cache handling of kallsyms with kcore perf annotate: Fix objdump line parsing offset validation perf tools: Fill in new definitions for madvise()/mmap() flags perf tools: Sharpen the libaudit dependencies test
-
由 Mikael Pettersson 提交于
My old @it.uu.se email address is going away, so update relevant files to point to my @gmail.com address instead. In sata_promise.c just delete the address, people can get it from MAINTAINERS. Signed-off-by: NMikael Pettersson <mikpe@it.uu.se> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 25 9月, 2013 3 次提交
-
-
由 Jayachandran C 提交于
The check cpu_needs_post_dma_flush() in mips_dma_sync_sg_for_cpu() and the check !plat_device_is_coherent() in mips_dma_sync_sg_for_device() can be moved outside the for loop. As a side effect, this also avoids a GCC bug that caused kernel compile to fail with the error: arch/mips/mm/dma-default.c: In function 'mips_dma_sync_sg_for_cpu': arch/mips/mm/dma-default.c:316:1: internal compiler error: in add_insn_before, at emit-rtl.c:3852 This gcc failure is seen in Code Sourcery toolchains [e.g. gcc version 4.7.2 (Sourcery CodeBench Lite 2012.09-99)] after commit "MIPS: Optimize current_cpu_type() for better code." Signed-off-by: NJayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5907/Reviewed-by: NMarkos Chandras <markos.chandras@imgtec.com> Tested-by: NMarkos Chandras <markos.chandras@imgtec.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Konrad Rzeszutek Wilk 提交于
Which disables in the ticketlock slowpath the Xen PV optimization's. Useful for diagnosing issues and comparing benchmarks in over-commit CPU scenarios. Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-
由 David Vrabel 提交于
On hosts with more than 168 GB of memory, a 32-bit guest may attempt to grant map an MFN that is error cannot lookup in its mapping of the m2p table. There is an m2p lookup as part of m2p_add_override() and m2p_remove_override(). The lookup falls off the end of the mapped portion of the m2p and (because the mapping is at the highest virtual address) wraps around and the lookup causes a fault on what appears to be a user space address. do_page_fault() (thinking it's a fault to a userspace address), tries to lock mm->mmap_sem. If the gntdev device is used for the grant map, m2p_add_override() is called from from gnttab_mmap() with mm->mmap_sem already locked. do_page_fault() then deadlocks. The deadlock would most commonly occur when a 64-bit guest is started and xenconsoled attempts to grant map its console ring. Introduce mfn_to_pfn_no_overrides() which checks the MFN is within the mapped portion of the m2p table before accessing the table and use this in m2p_add_override(), m2p_remove_override(), and mfn_to_pfn() (which already had the correct range check). All faults caused by accessing the non-existant parts of the m2p are thus within the kernel address space and exception_fixup() is called without trying to lock mm->mmap_sem. This means that for MFNs that are outside the mapped range of the m2p then mfn_to_pfn() will always look in the m2p overrides. This is correct because it must be a foreign MFN (and the PFN in the m2p in this case is only relevant for the other domain). Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com> Cc: Stefano Stabellini <stefano.stabellini@citrix.com> Cc: Jan Beulich <JBeulich@suse.com> -- v3: check for auto_translated_physmap in mfn_to_pfn_no_overrides() v2: in mfn_to_pfn() look in m2p_overrides if the MFN is out of range as it's probably foreign. Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
-