This patch uses the new pcie_get_minimum_link function to perform a check to
ensure that the adapter is hooked into a slot which is capable of providing the
necessary bandwidth. This check supersedes the original method which only
checked the current pci device. The new method is capable of determining the
minimum speed and link of an entire PCI chain.

-v2-
* update the error message to include encoding loss

CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A PCI Express device can potentially report a link width and speed which it will
not properly fulfill due to being plugged into a slower link higher in the
chain. This function walks up the PCI bus chain and calculates the minimum link
width and speed of this entire chain. This can be useful to enable a device to
determine if it has enough bandwidth for optimum functionality.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

pcie_link_width is the enum used to define the link width values for a pcie
device. This enum should not be contained solely in pci_hotplug.h, and this
patch moves it next to pci_bus_speed in pci.h
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

pcie_link_speed and pcix_bus_speed are arrays used by probe.c to correctly
convert lnksta register values into the pci_bus_speed enum. These static arrays
are useful outside probe for this purpose. This patch makes these defines into
conist arrays and exposes them with an extern header in drivers/pci/pci.h

-v2-
* move extern declarations to drivers/pci/pci.h

CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes several issues with the previous implementation of the
SFF data dump of SFP+ modules:

- removed the __IXGBE_READ_I2C flag - I2C access locking is handled in the
  HW specific routines

- fixed the read loop to read data from ee->offset to ee->len

- the reads fail if __IXGBE_IN_SFP_INIT is set in the process - this is
  needed because on some HW I2C operations can take long time and disrupt
  the SFP and link detection process
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_read/write_i2c_phy_82598() does not hold the SWFW_SYNC
semaphore for the entire function. Instead the lock is held only
during the phy.ops.read/write_reg operations. As result when the
function is being called simultaneously the I2C read/writes can
be corrupted.

The following patch introduces the SWFW_SYNC semaphore for the
entire ixgbe_read/write_i2c_phy_82598() function. To accomplish
this I had to create 2 separate functions:

ixgbe_read_phy_reg_mdi()
ixgbe_write_phy_reg_mdi()

Those functions are identical to ixgbe_read/write_phy_reg_generic()
sans the locking, and can be used in ixgbe_read/write_i2c_phy_82598()
with the SWFW_SYNC semaphore being held.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump the version number to better match with a similar version of the
out of tree driver.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for a new media type fiber_fixed.  This is useful
to avoid all the SFP+ hot plug support path on devices who's fix fiber need
not worry about such things.  This patch is needed for a following patch
that adds support for "fiber_fixed" devices.

v2: cleaned up logging message based on feedback from David Miller
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Originally ixgbe_device_supports_autoneg_fc() was only expected to
be called by copper devices.  This would lead to false information
to be displayed via ethtool.

v2: changed ixgbe_device_supports_autoneg_fc() to a bool function,
    it returns bool.  Based on feedback from David Miller
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the ixgbe driver uses the generic helper
pci_vfs_assigned instead of the ixgbe specific function
ixgbe_vfs_are_assigned.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled.  This defeats the ability to use VLAN tagging
to isolate user networks.  When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reverts commit

80b45261

which was implementing a 'cancelled' functionality to notify that
a cancelled request will not be replied.

This implementation was not used anywhere and therefore removed.
Signed-off-by: NAndi Shyti <andi@etezian.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver uses dev_err when enabling of AER fails (e.g. PCIe AER is not
supported). The dev_info is more appropriate to avoid console pollution.

Cc: sathya.perla@emulex.com
Cc: subbu.seetharaman@emulex.com
Cc: ajit.khaparde@emulex.com
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5762 devices sometimes incorrectly treat udp fragments as RMCP
packets and route to the APE. This patch sets the RX_MODE_IPV4_FRAG_FIX
bit for these devices which enables the proper behaviour.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PTP_CAPABLE tg3 devices have a gpio output that is toggled when the
free running counter matches a watchdog value. This patch adds support
to set the watchdog and enable this feature.

Since the output is controlled via bits in the EAV_REF_CLCK_CTL
register, we have to read-modify-write it when we stop/resume.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also remove the call to tg3_power_down_prepare() in tg3_power_down()
since tg3_close() calls it.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, when the interface was brought down, the driver would set
the power state to D3hot. In D3hot, we don't have access to the NVRAM.
This patch removes the call to set the power state to PCI_D3hot in
close. A following patch will implement the shutdown handler to properly
set the D3hot state when the system is going down.

Doing the above means that the TG3_PHYFLG_IS_LOW_POWER should not be
checked to validate access to the NVRAM.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe, the driver is incorrectly switching the power to Vaux on
the 5717 and later devices. At this point, we are in D0 state and
drawing maximum power. We also definitely have Vmain available. It
doesn't make sense to switch to Vaux since it has a lesser maximum power
draw and we might go over the limit. On a new system, we observe that
not all ports are recognized in some of the slots with this call in
place.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Completion status field should also be checked for non-zero error
condition.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update TCP delayed ACK and timestamp options setup to match latest bnx2x
firmware.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without resetting it, the bnx2i driver cannot use different options for
different iSCSI connections.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since unregister_netdevice_notifier() will replay the NETDEV_DOWN and
NETDEV_UNREGISTER_EVENTS, the cnic_dev_list will be cleaned up automatically.
The loop to cleanup the cnic_dev_list can be removed in cnic_release().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After this earlier commit to simplify probing:

    commit 4bd9b0ff
    cnic, bnx2x, bnx2: Simplify cnic probing.

we can now reliably receive netdev events and we can simplify the handling
of these events.  We now remove the logic that tries to handle missed
NETDEV_REGISTER events.

This change will allow cleanup to be simplified in the next patch.  We can
now rely on the play back of netdev events during
unregister_netdevice_notifier() to cleanup the structures.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a race between BlueFlame flow and stamping in post send flow.
Example:
	SW: Build WQE 0 on the TX buffer, except the ownership bit
	SW: Set ownership for WQE 0 on the TX buffer
	SW: Ring doorbell for WQE 0
	SW: Build WQE 1 on the TX buffer, except the ownership bit
	SW: Set ownership for WQE 1 on the TX buffer
	HW: Read WQE 0 and then WQE 1, before doorbell was rung/BF was done for WQE 1
	HW: Produce CQEs for WQE 0 and WQE 1
	SW: Process the CQEs, and stamp WQE 0 and WQE 1 accordingly (on the TX buffer)
	SW: Copy WQE 1 from the TX buffer to the BF register - ALREADY STAMPED!
	HW: CQE error with index 0xFFFF  - the BF WQE's control segment is STAMPED,
		so the BF index is 0xFFFF. Error: Invalid Opcode.
As a result QP enters the error state and no traffic can be sent.

Solution:
When stamping - do not stamp last completed wqe.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes this on PowerPC (at least):

net/core/pktgen.c: In function 'fill_packet_ipv6':
net/core/pktgen.c:2906:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
   udph->check = ~csum_ipv6_magic(&iph->saddr, &iph->daddr, udplen, IPPROTO_UDP, 0);
   ^
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e100 and e1000e.

The e100 patch from Andy simply updates the netif_printk() to use
%*ph to dump small buffers.

The changes to e1000e include a fix from Dean Nelson to resolve a
issue where a pci_clear_master() was accidentally dropped during a
conflict resolution. Wei Young provides 2 patches, one removes an
assignment of the default ring size because it was a duplicate. The
second changes the packet split receive structure to use
PS_PAGE_BUFFERS macro for the length so that problems won't occur
when the length is changed.

The remaining patches for e1000e are from Bruce Allan, where he
provides a number of fixes and updates for I218.  In addition, a
fix for 82583 which can disappear off the PCIe bus, to resolve this,
disable ASPM L1.  Bruce also provides a fix to a previous commit
(commit e60b22c5 e1000e: fix accessing to suspended device) so that
devices are only taken out of runtime power management for those
ethtool operations that must access device registers.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:
a) Also send ipv4 igmp messages with TC_PRIO_CONTROL

Cc: William Manley <william.manley@youview.com>
Cc: Lukas Tribus <luky-37@hotmail.com>
Acked-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The initialization of the PHY on I217/I218, while similar to 82579, must
also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus)
otherwise the PHY will be inaccessible by the MAC.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the device is runtime suspended (e.g. when there is no link), do not
wake it from D3 to read the PHY status; just set the values to typical
power-on defaults as is done when runtime PM is not enabled and there is no
link.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as
I217 and same PHY as I218.

The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous patch (commit e60b22c5 e1000e: fix accessing to suspended
device) added .begin and .complete ethtool driver callbacks so that the
device was resumed from Runtime Power Management (RPM) suspend state for
all ethtool operations.  This is overkill for operations which do not need
to access any registers in the device.  This patch makes it so that the
device is taken out of RPM suspend only for those ethtool operations that
must access device registers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Tx hang is an unintended consequence of another workaround that is in the
EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of
the MAC-PHY interconnect) is enabled.  The issue is resolved by setting
appropriate Tx re-transmission timeouts in the PHY and associated K1 entry
times in the MAC to allow enough transmissions to occur without triggering
a Tx hang.  A similar change is needed when linked at 10Mbps to improve
latency.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Alter the packet buffer allocation accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The jumbo frame configuration in the MAC/PHY should be reverted on 82579
and newer parts when the interface is brought down (not just when the MTU
is changed back to standard frame size) otherwise iAMT connections (e.g.
SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is
changed again.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 82583 can disappear off the PCIe bus.  This device is a modified 82574
which had the same problem which was fixed by disabling ASPM L1; disabling
it on 82583 fixes the issue on this device.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In structure e1000_rx_desc_packet_split, the size of wb.upper.length is
defined by a digit. This may introduce some problem when the length is
changed.

This patch use the macro PS_PAGE_BUFFERS for the definition. And move the
definition to hw.h.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is
called by e1000_sw_init() in the early stage of e1000_probe().

This patch just remove the duplicate assignment of this default ring size
value.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: NDa Yu Qiu <qiudayu@cn.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>