Tx hang is an unintended consequence of another workaround that is in the
EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of
the MAC-PHY interconnect) is enabled.  The issue is resolved by setting
appropriate Tx re-transmission timeouts in the PHY and associated K1 entry
times in the MAC to allow enough transmissions to occur without triggering
a Tx hang.  A similar change is needed when linked at 10Mbps to improve
latency.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Alter the packet buffer allocation accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The jumbo frame configuration in the MAC/PHY should be reverted on 82579
and newer parts when the interface is brought down (not just when the MTU
is changed back to standard frame size) otherwise iAMT connections (e.g.
SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is
changed again.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 82583 can disappear off the PCIe bus.  This device is a modified 82574
which had the same problem which was fixed by disabling ASPM L1; disabling
it on 82583 fixes the issue on this device.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In structure e1000_rx_desc_packet_split, the size of wb.upper.length is
defined by a digit. This may introduce some problem when the length is
changed.

This patch use the macro PS_PAGE_BUFFERS for the definition. And move the
definition to hw.h.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is
called by e1000_sw_init() in the early stage of e1000_probe().

This patch just remove the duplicate assignment of this default ring size
value.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: NDa Yu Qiu <qiudayu@cn.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In attempting to resolve a minor merge conflict, commit e5f2ef7a
(Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net) accidentally
dropped a call to pci_clear_master() that was intended to remain in place.

Commit 4e0855df (e1000e: fix pci-device enable-counter balance)
replaced a call to pci_disable_device() by one to pci_clear_master(). And then
commit 66148bab (e1000e: fix runtime power management transitions)
deleted a number of lines starting two lines following that call.

This patch restores the call to pci_clear_master() in __e1000_shutdown().

v2: added summary lines (enclosed in parens) following commit IDs
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After commit 4aa5dee4 ("net: convert resend IGMP to notifier event") we
have 1 read_unlock in bond_resend_igmp_join_requests which isn't paired
with a read_lock because it's removed by that commit.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

UDP checksums are optional, hence pktgen has been omitting them in
favour of performance. The optional flag UDPCSUM enables UDP
checksumming. If the output device supports hardware checksumming
the skb is prepared and marked CHECKSUM_PARTIAL, otherwise the
checksum is generated in software.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is useful for other VSOCK transport implemented outside the
net/vmw_vsock/ directory to use these headers.
Signed-off-by: NAsias He <asias@redhat.com>
Acked-by: NAndy King <acking@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Darren Hart says:

====================
Add support for the MinnowBoard in the pch_gbe driver. This was
originally sent to LKML as part of the MinnowBoard support series. That
is now partially merged and this version of the patch has been isolated
from those changes and is now completely self-contained.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default RX_QLEN()/TX_QLEN() didn't consider super speed
USB device, so only max 4 URBs are scheduled at the same time
for tx/rx, then USB3 NIC can't perform very well.

With this patch, both rx and tx thoughput are increased more than
100Mbps when doing iperf test on ax88179_178a USB 3.0 NIC.
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch centralizes computing of max rx/tx qlen, because:

- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too

Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inspired by commit f09e2249 (macvtap: restore
vlan header on user read). This patch adds hardware vlan tx support for
tuntap. This is done by copying vlan header directly into userspace in
tun_put_user() instead of doing it through __vlan_put_tag() in
dev_hard_start_xmit(). This eliminates one unnecessary memmove() in
vlan_insert_tag() for 802.1ad and 802.1q traffic.

pktgen test shows about 20% improvement for 802.1q traffic:

Before:
  662149pps 317Mb/sec (317831520bps) errors: 0
After:
  801033pps 384Mb/sec (384495840bps) errors: 0

Cc: Basil Gor <basil.gor@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch consolidates the SCTP checksum calculation code from various
places to a single new function, sctp_compute_cksum(skb, offset).
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Reviewed-by: NJulian Anastasov <ja@ssi.bg>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For small packets we can simplify xmit processing
by linearizing buffers with the header:
most packets seem to have enough head room
we can use for this purpose.
Since existing hypervisors require that header
is the first s/g element, we need a feature bit
for this.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This started out with fixing a sparse warning, then I realized that
the wrapper function bond_netpoll_info could just be removed
by rolling it into the enable code.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This started out with fixing a sparse warning, then I realized that
the wrapper function team_netpoll_info could just be collapsed away
by rolling it into the enable code.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This started out with fixing a sparse warning, then I realized that
the wrapper function br_netpoll_info could just be collapsed away
by rolling it into the enable code.

Also, eliminate unnecessary goto's
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have BOND_MODE_ROUNDROBIN pre-defined as 0, and it's the lowest
mode number.
Use it to check the arg lower bound instead of magic number 0 in
bond_mode_name.
Signed-off-by: NWang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MinnowBoard uses an AR803x PHY with the PCH GBE which requires
special handling. Use the MinnowBoard PCI Subsystem ID to detect this
and add a pci_device_id.driver_data structure and functions to handle
platform setup.

The AR803x does not implement the RGMII 2ns TX clock delay in the trace
routing nor via strapping. Add a detection method for the board and the
PHY and enable the TX clock delay via the registers.

This PHY will hibernate without link for 10 seconds. Ensure the PHY is
awake for probe and then disable hibernation. A future improvement would
be to convert pch_gbe to using PHYLIB and making sure we can wake the
PHY at the necessary times rather than permanently disabling it.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: netdev@vger.kernel.org

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid using magic numbers when we have perfectly good defines just lying
around.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: netdev@vger.kernel.org

No users outside net/core/dev.c.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Idea of this patch is to add optional limitation of number of
unsent bytes in TCP sockets, to reduce usage of kernel memory.

TCP receiver might announce a big window, and TCP sender autotuning
might allow a large amount of bytes in write queue, but this has little
performance impact if a large part of this buffering is wasted :

Write queue needs to be large only to deal with large BDP, not
necessarily to cope with scheduling delays (incoming ACKS make room
for the application to queue more bytes)

For most workloads, using a value of 128 KB or less is OK to give
applications enough time to react to POLLOUT events in time
(or being awaken in a blocking sendmsg())

This patch adds two ways to set the limit :

1) Per socket option TCP_NOTSENT_LOWAT

2) A sysctl (/proc/sys/net/ipv4/tcp_notsent_lowat) for sockets
not using TCP_NOTSENT_LOWAT socket option (or setting a zero value)
Default value being UINT_MAX (0xFFFFFFFF), meaning this has no effect.

This changes poll()/select()/epoll() to report POLLOUT
only if number of unsent bytes is below tp->nosent_lowat

Note this might increase number of sendmsg()/sendfile() calls
when using non blocking sockets,
and increase number of context switches for blocking sockets.

Note this is not related to SO_SNDLOWAT (as SO_SNDLOWAT is
defined as :
 Specify the minimum number of bytes in the buffer until
 the socket layer will pass the data to the protocol)

Tested:

netperf sessions, and watching /proc/net/protocols "memory" column for TCP

With 200 concurrent netperf -t TCP_STREAM sessions, amount of kernel memory
used by TCP buffers shrinks by ~55 % (20567 pages instead of 45458)

lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6     1880      2   45458   no     208   yes  ipv6        y  y  y  y  y  y  y  y  y  y  y  y  y  n  y  y  y  y  y
TCP       1696    508   45458   no     208   yes  kernel      y  y  y  y  y  y  y  y  y  y  y  y  y  n  y  y  y  y  y

lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6     1880      2   20567   no     208   yes  ipv6        y  y  y  y  y  y  y  y  y  y  y  y  y  n  y  y  y  y  y
TCP       1696    508   20567   no     208   yes  kernel      y  y  y  y  y  y  y  y  y  y  y  y  y  n  y  y  y  y  y

Using 128KB has no bad effect on the throughput or cpu usage
of a single flow, although there is an increase of context switches.

A bonus is that we hold socket lock for a shorter amount
of time and should improve latencies of ACK processing.

lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local       Remote      Local  Elapsed Throughput Throughput  Local Local  Remote Remote Local   Remote  Service
Send Socket Recv Socket Send   Time               Units       CPU   CPU    CPU    CPU    Service Service Demand
Size        Size        Size   (sec)                          Util  Util   Util   Util   Demand  Demand  Units
Final       Final                                             %     Method %      Method
1651584     6291456     16384  20.00   17447.90   10^6bits/s  3.13  S      -1.00  U      0.353   -1.000  usec/KB

 Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':

           412,514 context-switches

     200.034645535 seconds time elapsed

lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local       Remote      Local  Elapsed Throughput Throughput  Local Local  Remote Remote Local   Remote  Service
Send Socket Recv Socket Send   Time               Units       CPU   CPU    CPU    CPU    Service Service Demand
Size        Size        Size   (sec)                          Util  Util   Util   Util   Demand  Demand  Units
Final       Final                                             %     Method %      Method
1593240     6291456     16384  20.00   17321.16   10^6bits/s  3.35  S      -1.00  U      0.381   -1.000  usec/KB

 Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':

         2,675,818 context-switches

     200.029651391 seconds time elapsed
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-By: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several call sites use the hardcoded following condition :

sk_stream_wspace(sk) >= sk_stream_min_wspace(sk)

Lets use a helper because TCP_NOTSENT_LOWAT support will change this
condition for TCP sockets.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After this file has moved to the uapi section, we also need to update
this in the maintainers file.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to show CPSW hardware statistics to user via ethtool
so user can find if there were any error reported by hardware or
the system is over loaded duing high data rate transfer.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error is found by the checkpatch.pl tools.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need rtnl protection while reading slave_cnt and updating
the .fail_over_mac, and it also follows the logic "don't change
anything slave-related without rtnl". :)
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/bonding/bond_sysfs.c:1302: ERROR: else should follow close brace '}'
net/bonding/bond_sysfs.c:1314: ERROR: else should follow close brace '}'
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.

bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c
Signed-off-by: NNeel Patel <neepatel@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NNishank Trivedi <nistrive@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gets rid of the following warning:

net/9p/trans_rdma.c:594:12: warning: ‘rdma_cancelled’ defined but not used [-Wunused-function]
 static int rdma_cancelled(struct p9_client *client, struct p9_req_t *req)

The rdma_cancelled function is not called anywhere in the kernel
Signed-off-by: NAndi Shyti <andi@etezian.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
The following patches are mostly for providing MAC
filtering ability for VFs. Pls apply. Thanks!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the UC-list is being deleted from the HW MAC table, but the primary
MAC is not.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SH-R and Lancer-R, GET_MAC_LIST cmd is better supported
(instead of NTWK_MAC_QUERY cmd) to query provisioned MAC addresses.
Similiarly, (on SH-R and Lancer-R) SET_MAC_LIST must be used by the PF to
provision a permanent MAC addresses to the VF.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>