Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Some chips were unstable with repeated setup/teardown of the hardware status
page.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This avoids early termination for long-running commands.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Previous attempts at interrupt mitigation had been foiled by i915_wait_irq's
failure to update the sarea seqno value when the status page indicated that
the seqno had already been passed.  MSI support has been seen to cut CPU
costs by up to 40% in some workloads by avoiding other expensive interrupt
handlers for frequent graphics interrupts.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It is already correctly detected by the kernel for use in suspend/resume.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The driver can know what hardware requires MI_BATCH_BUFFER vs
MI_BATCH_BUFFER_START; there's no reason to let user mode configure this.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix a pointer cast warning in the SIS DRM code.

This was introduced in patch ce65a44d.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix the SIS DRM memory allocator if the SIS FB built as a module.  The SIS DRM
code initialises the mm allocation hooks, but _only_ if the SIS FB is not
built as a module because it depends on CONFIG_FB_SIS, and that's unset if the
SIS FB is not built in.  It must check CONFIG_FB_SIS_MODULE as well.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There is no point in considering FreeBSD et al.  in the linux kernel
source code.
Signed-off-by: NCarlos R. Mafra <crmafra@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (25 commits)
  staging: at76_usb wireless driver
  Staging: workaround build system bug
  Staging: Lindent sxg.c
  Staging: SLICOSS: Call pci_release_regions at driver exit
  Staging: SLICOSS: Fix remaining type names
  Staging: SLICOSS: Fix warnings due to static usage
  Staging: SLICOSS: lots of checkpatch fixes
  Staging: go7007 v4l fixes
  Staging: Fix gcc warnings in sxg
  Staging: add echo cancelation module
  Staging: add wlan-ng prism2 usb driver
  Staging: add w35und wifi driver
  Staging: USB/IP: add host driver
  Staging: USB/IP: add client driver
  Staging: USB/IP: add common functions needed
  Staging: add the go7007 video driver
  Staging: add me4000 pci data collection driver
  Staging: add me4000 firmware files
  Staging: add sxg network driver
  Staging: add Alacritech slicoss network driver
  ...

Fixed up conflicts due to taint flags changes and MAINTAINERS cleanup in
MAINTAINERS, include/linux/kernel.h and kernel/panic.c.

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (47 commits)
  hwmon: (adm1026) Prevent log spamming
  hwmon: (adm1026) Fix debug messages
  hwmon: (adm1029) Use mask for fan_div value
  hwmon: (adt7470) Add documentation
  hwmon: (ibmaem) Automatically load on IBM systems via DMI
  hwmon: (ibmpex) Automatically load on IBM systems via DMI
  hwmon: (w83781d) Use new style driver binding
  hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
  hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
  hwmon: (w83781d) Additional information about AS99127F PWM
  hwmon: (w83781d) Detect alias chips
  hwmon: (w83781d) Refactor beep enable handling
  hwmon: Drop dead links to old National Semiconductor chip datasheets
  hwmon: (w83791d) add support for thermal cruise mode
  hwmon: (w83791d) add pwm_enable support
  hwmon: (w83791d) add manual PWM support
  hwmon: (w83791d) fan 4/5 pins can also be used for gpio
  hwmon: (max1619) Use inline functions instead of macros
  hwmon: (it87) Fix thermal sensor type values
  hwmon: (lm78) Convert to a new-style i2c driver
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Fix debugfs_create_dir's error checking method for sound/soc/
  ALSA: ASoC: Convert playpaq_wm8510 to bulk route registration API
  ALSA: kernel docs: fix sound/core/ kernel-doc
  ALSA: Handle NULL jacks in snd_jack_report()
  ALSA: hda - Fix PCM type of Nvidia HDMI devices

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: remove __generic_unplug_device() from exports
  block: move q->unplug_work initialization
  blktrace: pass zfcp driver data
  blktrace: add support for driver data
  block: fix current kernel-doc warnings
  block: only call ->request_fn when the queue is not stopped
  block: simplify string handling in elv_iosched_store()
  block: fix kernel-doc for blk_alloc_devt()
  block: fix nr_phys_segments miscalculation bug
  block: add partition attribute for partition number
  block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
  softirq: Add support for triggering softirq work on softirqs.

* 'for-linus' of git://www.jni.nu/cris:
  CRIS: proper defconfig setup
  [CRIS] Rename boot-linkscripts and fix the path to them.

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (39 commits)
  [SCSI] sd: fix compile failure with CONFIG_BLK_DEV_INTEGRITY=n
  libiscsi: fix locking in iscsi_eh_device_reset
  libiscsi: check reason why we are stopping iscsi session to determine error value
  [SCSI] iscsi_tcp: return a descriptive error value during connection errors
  [SCSI] libiscsi: rename host reset to target reset
  [SCSI] iscsi class: fix endpoint id handling
  [SCSI] libiscsi: Support drivers initiating session removal
  [SCSI] libiscsi: fix data corruption when target has to resend data-in packets
  [SCSI] sd: Switch kernel printing level for DIF messages
  [SCSI] sd: Correctly handle all combinations of DIF and DIX
  [SCSI] sd: Always print actual protection_type
  [SCSI] sd: Issue correct protection operation
  [SCSI] scsi_error: fix target reset handling
  [SCSI] lpfc 8.2.8 v2 : Add statistical reporting control and additional fc vendor events
  [SCSI] lpfc 8.2.8 v2 : Add sysfs control of target queue depth handling
  [SCSI] lpfc 8.2.8 v2 : Revert target busy in favor of transport disrupted
  [SCSI] scsi_dh_alua: remove REQ_NOMERGE
  [SCSI] lpfc 8.2.8 : update driver version to 8.2.8
  [SCSI] lpfc 8.2.8 : Add MSI-X support
  [SCSI] lpfc 8.2.8 : Update driver to use new Host byte error code DID_TRANSPORT_DISRUPTED
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
  ipv4: Add a missing rcu_assign_pointer() in routing cache.
  [netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
  xen-netfront: Avoid unaligned accesses to IP header
  lmc: copy_*_user under spinlock
  [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA

When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: NCorentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add at least the bare minimum of documentation for this chip.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.

[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350

This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for pwm_enable.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add PWM manual control.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface. 
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Macros evaluating their arguments more than once are evil.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.

Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>

The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: NJean Delvare <khali@linux-fr.org>