The writeback ring pointer and IH ring pointer are read using le32_to_cpu
so we do not want the chip to byteswap them on big-endian.

We still want to byteswap the ring itself and the IBs, so we don't touch
that but we remove setting of the byteswap bits in CP_RB_RPTR_ADDR and
IH_CNTL.

In general, for things like that where we control all the accessors easily,
we are better off doing the swap in SW rather than HW. Paradoxally, it does
keep the code closer to x86 and avoid using poorly tested HW features.

I also changed the use of RADEON_ to R600_ in a couple of cases to be more
consistent with the surrounding code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NMichel Dänzer <michel@daenzer.net>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just defining rdev->rmmio properly in the first place should do
the trick. In some cases, the cast were also complete dups as
the original variable was already of the right type.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These small changes should allow GEM to be used with non shmem objects as
well as shmem objects. In the GMA500 case it allows the base framebuffer to
appear as a GEM object and thus acquire a handle and work with KMS.

For i915 it ought to be trivial to get back the wasted memory but putting the
system fb back into stolen RAM and in general I can imagine it allowing the
use of GEM and thus KMS with all the older cards that have their framebuffer
firmly placed in video RAM.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Tested-by: NRob Clark <rob@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The video= parameter of the DRM drivers supports some additional flags that
the normal fb drivers do not have. They also allow to limit these flags to
specific outputs. Both things were previously undocumented.

Also the parsing of the line had some oddities:
-A lot of misplaced options were silently ignored or partly rejected instead
 of stopping the parsing immediately
-The 'R' option is documented to follow the 'M' option if specified. It is not
 documented that 'M' is needed to specify 'R' (also this is the case for normal
 fb drivers). In fact the code is correct for normal fb drivers but wrong for
 DRM ones.
 The old code allowed 'R' only _before_ 'M' (since it parses backwards) and only
 if 'M' is given at all which is not needed for the DRM drivers.
-the margins option ('m') was parsed but later ignored even if the later
 functions support it.
-specifying multiple enable options at the same time did not lead to an error.
-specifying something bogus for horizontal resolution (i.e. other things as
 digits) did not lead to an error but an invalid resolution was used.

If any errors are encountered the position of the faulting string is now
printed to the user and the complete mode is ignored. This gives much
more consistent error behaviour.

I also removed some useless assignments and changed the local flag variables
to be bool.
Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

WARNING: drivers/gpu/drm/radeon/radeon.o(.text+0x5d1fc): Section mismatch in reference from the function radeon_get_clock_info() to the function .devinit.text:radeon_read_clocks_OF()
The function radeon_get_clock_info() references
the function __devinit radeon_read_clocks_OF().
This is often because radeon_get_clock_info lacks a __devinit
annotation or the annotation of radeon_read_clocks_OF is wrong.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also disable the ascii dump and remove the literal printing of the
KERN_ERR macro in the log:

   [drm:drm_edid_block_valid] *ERROR* Raw EDID:
   <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................

v2: Remove the trailing empty line as well.
Signed-off-by: NTormod Volden <debian.tormod@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Those chips have crt2_ddc bus.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=39672Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-core-next

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
  drm/nouveau: pass flag to engine fini() method on suspend
  drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
  drm/nv40/gr: rewrite/split context takedown functions
  drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
  drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
  drm/nouveau: Add a quirk for Gigabyte NX86T
  drm/nouveau: do not leak in nv20_graph_create
  drm/nv50/dp: fix hack to work for macbooks booted via EFI

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It may not be necessary to fail in certain cases (such as failing to idle)
on module unload, whereas on suspend it's important to ensure a consistent
state can be restored on resume.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It's completely pointless to save the PGRAPH context when destroying a
channel, so don't bother.

This commit should also fix kernel.org bug 39422, where the DRM channel
state was incorrectly being saved because we left PGRAPH FIFO access
enabled while running the ctxprog.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

If the connector table is lying, which it often does on the boards of a
particular manufacturer, we may end up doing the wrong thing.  Listen
to the encoder table instead, it's more reliable.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The connector table lies, the card has DVI-I not HDMI
Fixes bug https://bugs.freedesktop.org/show_bug.cgi?id=35675

v2: Mention the bugreport
Signed-off-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

If we return due to an unknown chipset in
drivers/gpu/drm/nouveau/nv20_graph.c:nv20_graph_create() we'll leak the
memory allocated to 'pgraph'.

This patch should fix the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Reviewed-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The 3D driver need to get the pipe to backend
map to certain things.  Add a query to get the
info.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Include the device id in the bus-id to give userspace a way to open
the correct "cardN" when there are multiple device instances.
Signed-off-by: NRob Clark <rob@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use the fence of the new frontbuffer, if any.

Generating a new fence could cause us to wait for completely unrelated
rendering to finish before performing the flip.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge branch 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6 into drm-core-next

* 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6: (52 commits)
  drm/i915: provide module parameter description
  drm/i915: add module parameter compiler hints
  drm/i915/bios: Avoid temporary allocation whilst searching for downclock
  drm/i915: Cache GT fifo count for SandyBridge
  i915: Fix opregion notifications
  drm/i915: TVDAC_STATE_CHG does not indicate successful load-detect
  drm/i915: Select correct pipe during TV detect
  drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
  Revert "drm/i915: enable rc6 by default"
  drm/i915: Clean up i915_driver_load failure path
  drm/i915: Enable i915 frame buffer compression by default
  drm/i915: Share the common work of disabling active FBC before updating
  drm/i915: Perform intel_enable_fbc() from a delayed task
  drm/i915: Disable FBC across page-flipping
  drm/i915: Set persistent-mode for ILK/SNB framebuffer compression
  drm/i915: Use of a CPU fence is mandatory to update FBC regions upon CPU writes
  drm/i915: Remove vestigial pitch from post-gen2 FBC control routines
  drm/i915: Replace direct calls to vfunc.disable_fbc with intel_disable_fbc()
  drm/i915: Only export the generic intel_disable_fbc() interface
  drm/i915: Enable GPU reset on Ivybridge.
  ...

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

The read back of the available FIFO entries is vital for system
stability, but extremely costly. However, we only need a guide so as to
avoid eating into the reserved entries and since we are the only
consumer we can cache the read of the count from the last write.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Tested-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Do not use this bit to indicate that load detection has completed,
instead just wait for vblank, at which point the load registers will
have been updated.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NYi Sun <yi.sun@intel.com>

Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NYi Sun <yi.sun@intel.com>

This pulls in all the drm fixes up to this point which are needed
for some -next patches to work.

drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter.  This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.

[airlied: update for new callsite]
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDave Airlie <airlied@redhat.com>

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: NKeith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NLin Ming <ming.m.lin@intel.com>

That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions.  Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.

Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] msp3400: fill in v4l2_tuner based on vt->type field
  [media] tuner-core.c: don't change type field in g_tuner or g_frequency
  [media] cx18/ivtv: fix g_tuner support
  [media] tuner-core: power up tuner when called with s_power(1)
  [media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
  [media] tuner-core: simplify the standard fixup
  [media] tuner-core/v4l2-subdev: document that the type field has to be filled in
  [media] v4l2-subdev.h: remove unused s_mode tuner op
  [media] feature-removal-schedule: change in how radio device nodes are handled
  [media] bttv: fix s_tuner for radio
  [media] pvrusb2: fix g/s_tuner support
  [media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
  [media] tuner-core: fix tuner_resume: use t->mode instead of t->type
  [media] tuner-core: fix s_std and s_tuner

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Reintroduce dropped call to check_wakeup_irqs

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: drop spinlock before calling cifs_put_tlink
  cifs: fix expand_dfs_referral
  cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
  cifs: factor smb_vol allocation out of cifs_setup_volume_info
  cifs: have cifs_cleanup_volume_info not take a double pointer
  cifs: fix build_unc_path_to_root to account for a prefixpath
  cifs: remove bogus call to cifs_cleanup_volume_info