The original ia64 udelay() was simple, but flawed for platforms without
synchronized ITCs:  a preemption and migration to another CPU during the
while-loop likely resulted in too-early termination or very, very
lengthy looping.

The first fix (now in 2.6.15) broke the delay loop into smaller,
non-preemptible chunks, reenabling preemption between the chunks.  This
fix is flawed in that the total udelay is computed to be the sum of just
the non-premptible while-loop pieces, i.e., not counting the time spent
in the interim preemptible periods.  If an interrupt or a migration
occurs during one of these interim periods, then that time is invisible
and only serves to lengthen the effective udelay().

This new fix backs out the current flawed fix and returns to a simple
udelay(), fully preemptible and interruptible.  It implements two simple
alternative udelay() routines:  one a default generic version that uses
ia64_get_itc(), and the other an sn-specific version that uses that
platform's RTC.
Signed-off-by: NJohn Hawkes <hawkes@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Fix XPC so that it does not deliver any messages until the connected
callout has returned, as well as, prevent the disconnected callout to
occur before the disconnecting callout has returned.
Signed-off-by: NDean Nelson <dcn@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The __sn_cnodeid_to_nasid array was incorrectly sized at MAX_NUMNODES.
On a large system, this array could overflow.  The following patch
corrects this by defining it to MAX_COMPACT_NODES.
Signed-off-by: NDean Roe <roe@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Export sn_pcidev_info_get.

Signed-off-by Mark Maule <maule@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

This one falls into the "present for Andrew Morton" category to address
his wishlist for a compiler warning free build ;-)
Signed-off-by: NTony Luck <tony.luck@intel.com>

Remove obsolete SGI address
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

General SN2 code cleanup:
 - Do not initialize global variables to zero
 - Use kzalloc instead of kmalloc+memset
 - Check kmalloc return values
 - Do not obfuscate spin lock calls
 - Remove some unused code
 - Various formatting cleanups
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Remove symbol exports from ia64_ksyms.c that are already exported in
lib/string.c.
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Signed-off-by: NTony Luck <tony.luck@intel.com>

1. The tracee can go from ptrace_stop() to do_signal_stop()
   after __ptrace_unlink(p).

2. It is unsafe to __ptrace_unlink(p) while p->parent may wait
   for tasklist_lock in ptrace_detach().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

copy_process:

	attach_pid(p, PIDTYPE_PID, p->pid);
	attach_pid(p, PIDTYPE_TGID, p->tgid);

What if kill_proc_info(p->pid) happens in between?

copy_process() holds current->sighand.siglock, so we are safe
in CLONE_THREAD case, because current->sighand == p->sighand.

Otherwise, p->sighand is unlocked, the new process is already
visible to the find_task_by_pid(), but have a copy of parent's
'struct pid' in ->pids[PIDTYPE_TGID].

This means that __group_complete_signal() may hang while doing

	do ... while (next_thread() != p)

We can solve this problem if we reverse these 2 attach_pid()s:

	attach_pid() does wmb()

	group_send_sig_info() calls spin_lock(), which
	provides a read barrier. // Yes ?

I don't think we can hit this race in practice, but still.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is a window after copy_process() unlocks ->sighand.siglock
and before it adds the new thread to the thread list.

In that window __group_complete_signal(SIGKILL) will not see the
new thread yet, so this thread will start running while the whole
thread group was supposed to exit.

I beleive we have another good reason to place attach_pid(PID/TGID)
under ->sighand.siglock. We can do the same for

	release_task()->__unhash_process()

	de_thread()->switch_exec_pids()

After that we don't need tasklist_lock to iterate over the thread
list, and we can simplify things, see for example do_sigaction()
or sys_times().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Looks like somebody forgot to use the _bh spin_lock variant. We ran into a 
deadlock where br->hello_timer expired while br_stp_disable_br() walked 
br->port_list. 
Signed-off-by: NAdrian Drzewiecki <z@drze.net>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To find out if a packet needs to be handled by IPsec after SNAT, packets
are currently rerouted in POST_ROUTING and a new xfrm lookup is done. This
breaks SNAT of non-unicast packets to non-local addresses because the
packet is routed as incoming packet and no neighbour entry is bound to the
dst_entry. In general, it seems to be a bad idea to replace the dst_entry
after the packet was already sent to the output routine because its state
might not match what's expected.

This patch changes the xfrm lookup in POST_ROUTING to re-use the original
dst_entry without routing the packet again. This means no policy routing
can be used for transport mode transforms (which keep the original route)
when packets are SNATed to match the policy, but it looks like the best
we can do for now.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an oops reported by Adrian Bunk in cifs_user_read when a null
read response is returned on a forcedirectio mount.
Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix issues with the NeoMagic framebuffer driver.

It nicely complements my previous fix already in linus' tree.  The only
thing missing now is that the external CRT will not be activated at neofb
init when external-only is selected, either by register read or
module/kernel parameter.

Testing was done on a Dell Latitude CPi-A/NM2200 chip.

Previous behaviour:
- before booting linux, set the preferred display config X via FN+F8

- boot linux, neofb stores the register values in a private
  variable

- change the display config to Y via keystroke

- leave the machine in peace until display is blanked

- touching any key will result in display config X being restored

- booting up, the BIOS will acknowledge config Y, though...

Current behaviour:
At the time of unblanking, config Y is honoured because we now read back
register contents instead of just overwriting them with outdated values.

Signed-off by: Christian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add some more gitignore files for i386 architecture.  This files are
created during the build process of a i386 kernel.
Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This path isn't obvious.  It looks as if the kernel will be taking three
args from the user stack, but it only takes one from there.
Signed-off-by: NAlbert Cahalan <acahalan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make the FRV arch use virtual interrupt disablement because accesses to the
processor status register (PSR) are relatively slow and because we will
soon have the need to deal with multiple interrupt controls at the same
time (separate h/w and inter-core interrupts).

The way this is done is to dedicate one of the four integer condition code
registers (ICC2) to maintaining a virtual interrupt disablement state
whilst inside the kernel.  This uses the ICC2.Z flag (Zero) to indicate
whether the interrupts are virtually disabled and the ICC2.C flag (Carry)
to indicate whether the interrupts are physically disabled.

ICC2.Z is set to indicate interrupts are virtually disabled.  ICC2.C is set
to indicate interrupts are physically enabled.  Under normal running
conditions Z==0 and C==1.

Disabling interrupts with local_irq_disable() doesn't then actually
physically disable interrupts - it merely sets ICC2.Z to 1.  Should an
interrupt then happen, the exception prologue will note ICC2.Z is set and
branch out of line using one instruction (an unlikely BEQ).  Here it will
physically disable interrupts and clear ICC2.C.

When it comes time to enable interrupts (local_irq_enable()), this simply
clears the ICC2.Z flag and invokes a trap #2 if both Z and C flags are
clear (the HI integer condition).  This can be done with the TIHI
conditional trap instruction.

The trap then physically reenables interrupts and sets ICC2.C again.  Upon
returning the interrupt will be taken as interrupts will then be enabled.
Note that whilst processing the trap, the whole exceptions system is
disabled, and so an interrupt can't happen till it returns.

If no pending interrupt had happened, ICC2.C would still be set, the HI
condition would not be fulfilled, and no trap will happen.

Saving interrupts (local_irq_save) is simply a matter of pulling the ICC2.Z
flag out of the CCR register, shifting it down and masking it off.  This
gives a result of 0 if interrupts were enabled and 1 if they weren't.

Restoring interrupts (local_irq_restore) is then a matter of taking the
saved value mentioned previously and XOR'ing it against 1.  If it was one,
the result will be zero, and if it was zero the result will be non-zero.
This result is then used to affect the ICC2.Z flag directly (it is a
condition code flag after all).  An XOR instruction does not affect the
Carry flag, and so that bit of state is unchanged.  The two flags can then
be sampled to see if they're both zero using the trap (TIHI) as for the
unconditional reenablement (local_irq_enable).

This patch also:

 (1) Modifies the debugging stub (break.S) to handle single-stepping crossing
     into the trap #2 handler and into virtually disabled interrupts.

 (2) Removes superseded fixup pointers from the second instructions in the trap
     tables (there's no a separate fixup table for this).

 (3) Declares the trap #3 vector for use in .org directives in the trap table.

 (4) Moves irq_enter() and irq_exit() in do_IRQ() to avoid problems with
     virtual interrupt handling, and removes the duplicate code that has now
     been folded into irq_exit() (softirq and preemption handling).

 (5) Tells the compiler in the arch Makefile that ICC2 is now reserved.

 (6) Documents the in-kernel ABI, including the virtual interrupts.

 (7) Renames the old irq management functions to different names.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make various alterations and fixes to the FRV arch:

 (1) Resyncs the FRV system call collection with the i386 arch.

 (2) Discards __iounmap() as it's not used.

 (3) Fixes the use of the SWAP/SWAPI instruction to get the arguments the right
     way around in atomic.h, and also to get the asm constraints correct.

 (4) Moves copy_to/from_user_page() to asm/cacheflush.h to be consistent with
     other archs.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_TIME_LOW_RES is a temporary way for architectures to signal that
they simply return xtime in do_gettimeoffset().  In this corner-case we
want to round up by resolution when starting a relative timer, to avoid
short timeouts.  This will go away with the GTOD framework.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix __delay implementation.  Called with an argument "1" or "0" it would
loop nearly forever (since (1/2)-1 = 0xffffffff).
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Jean-Luc Leger <reiga@dspnet.fr.eu.org> found this obvious typo.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert commit d7102e95:

    [PATCH] sched: filter affine wakeups

Apparently caused more than 10% performance regression for aim7 benchmark.
The setup in use is 16-cpu HP rx8620, 64Gb of memory and 12 MSA1000s with 144
disks.  Each disk is 72Gb with a single ext3 filesystem (courtesy of HP, who
supplied benchmark results).

The problem is, for aim7, the wake-up pattern is random, but it still needs
load balancing action in the wake-up path to achieve best performance.  With
the above commit, lack of load balancing hurts that workload.

However, for workloads like database transaction processing, the requirement
is exactly opposite.  In the wake up path, best performance is achieved with
absolutely zero load balancing.  We simply wake up the process on the CPU that
it was previously run.  Worst performance is obtained when we do load
balancing at wake up.

There isn't an easy way to auto detect the workload characteristics.  Ingo's
earlier patch that detects idle CPU and decide whether to load balance or not
doesn't perform with aim7 either since all CPUs are busy (it causes even
bigger perf.  regression).

Revert commit d7102e95, which causes more
than 10% performance regression with aim7.
Signed-off-by: NKen Chen <kenneth.w.chen@intel.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages).  This happens if the process forks meanwhile, and the parent
writes to that page.  As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW.  In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.

In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.

This patch adds madvise options to control whether memory range is inherited
across fork.  Useful e.g.  for when hardware is doing DMA from/into these
pages.  Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Acked-by: NHugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update Documentation/kprobes.txt to reflect Kprobes enhancements and other
recent developments.
Acked-by: NAnanth Mavinakayanahalli <mananth@in.ibm.com>
Signed-off-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The changes in the tty related code introduced wrong parenthesis in a if
condition in the isdn_tty_at_cout function.  This caused access to index -1
in the dev->drv[] array.  This patch change it back to the correct
condition from the previous versions.
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The correct way to export hyperthreading based functions is to predicate
them on CONFIG_X86_HT.  Without this, the topology exporting patch breaks
the build on all non-PC x86 subarchitectures.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If 2 threads attached to the same process are blocking on different locks on
different files (maybe even on different servers) but have the same lock
arguments (i.e.  same offset+length - actually quite common, since most
processes try to lock the entire file) then the first GRANTED call that wakes
one up will also wake the other.

Currently when the NLM_GRANTED callback comes in, lockd walks the list of
blocked locks in search of a match to the lock that the NLM server has
granted.  Although it checks the lock pid, start and end, it fails to check
the filehandle and the server address.

By checking the filehandle and server IP address, we ensure that this only
happens if the locks truly are referencing the same file.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch reverts commit f93ea411:
  [PATCH] jbd: split checkpoint lists

This broke journal_flush() for OCFS2, which is its method of being sure
that metadata is sent to disk for another node.

And two related commits 8d3c7fce and
43c3e6f5 with the subjects:
  [PATCH] jbd: log_do_checkpoint fix
  [PATCH] jbd: remove_transaction fix

These seem to be incremental bugfixes on the original patch and as such are
no longer needed.
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When the _CRS for a single HPET contains multiple EXTENDED_IRQ resources,
we overwrote hdp->hd_nirqs every time we found one.

So the driver worked when all the IRQs were described in a single
EXTENDED_IRQ resource, but failed when multiple resources were used.
(Strictly speaking, I think the latter is actually more correct, but both
styles have been used.)

Someday we should remove all the ACPI stuff from hpet.c and use PNP driver
registration instead.  But currently PNP_MAX_IRQ is 2, and HPETs often have
more IRQs.  Hint, hint, Adam :-)
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: NBob Picco <robert.picco@hp.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix hole where tty structure can be released when reference count is non
zero.  Existing code can sleep without tty_sem protection between deciding
to release the tty structure (setting local variables tty_closing and
otty_closing) and setting TTY_CLOSING to prevent further opens.  An open
can occur during this interval causing release_dev() to free the tty
structure while it is still referenced.

This should fix bugzilla.kernel.org [Bug 6041] New: Unable to handle kernel
paging request

In Bug 6041, tty_open() oopes on accessing the tty structure it has
successfully claimed.  Bug was on SMP machine with the same tty being
opened and closed by multiple processes, and DEBUG_PAGEALLOC enabled.
Signed-off-by: NPaul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The PageCompound check before access_process_vm's set_page_dirty_lock is no
longer necessary, so remove it.  But leave the PageCompound checks in
bio_set_pages_dirty, dio_bio_complete and nfs_free_user_pages: at least some
of those were introduced as a little optimization on hugetlb pages.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Somehow I imagined that calling a NULL destructor would free a compound page
rather than oopsing.  No, we must supply a default destructor, __free_pages_ok
using the order noted by prep_compound_page.  hugetlb can still replace this
as before with its own free_huge_page pointer.

The case that needs this is not common: rarely does put_compound_page's
put_page_testzero bring the count down to 0.  But if get_user_pages is applied
to some part of a compound page, without immediate release (e.g.  AIO or
Infiniband), then it's possible for its put_page to come after the containing
vma has been unmapped and the driver done its free_pages.

That's just the kind of case compound pages are supposed to be guarding
against (but Nick points out, nor did PageReserved handle this right).
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If a compound page has its own put_page_testzero destructor (the only current
example is free_huge_page), that is noted in page[1].mapping of the compound
page.  But that's rather a poor place to keep it: functions which call
set_page_dirty_lock after get_user_pages (e.g.  Infiniband's
__ib_umem_release) ought to be checking first, otherwise set_page_dirty is
liable to crash on what's not the address of a struct address_space.

And now I'm about to make that worse: it turns out that every compound page
needs a destructor, so we can no longer rely on hugetlb pages going their own
special way, to avoid further problems of page->mapping reuse.  For example,
not many people know that: on 50% of i386 -Os builds, the first tail page of a
compound page purports to be PageAnon (when its destructor has an odd
address), which surprises page_add_file_rmap.

Keep the compound page destructor in page[1].lru.next instead.  And to free up
the common pairing of mapping and index, also move compound page order from
index to lru.prev.  Slab reuses page->lru too: but if we ever need slab to use
compound pages, it can easily stack its use above this.

(akpm: decoded version of the above: the tail pages of a compound page now
have ->mapping==NULL, so there's no need for the set_page_dirty[_lock]()
caller to check that they're not compund pages before doing the dirty).
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reduce stack usage in the pkt_start_write() function.  Even though it's not
currently a real problem, the pages and offsets arrays can be eliminated,
which saves approximately 1000 bytes of stack space.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Unlocking the door when the disc is in use is obviously not good, because then
it's possible to eject the disc at the wrong time and cause severe disc data
corruption.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If opening for write fails, the open method should return -EROFS.  This makes
"mount" try again with a read-only mount, instead of just giving up.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Change some messages that don't indicate an error so that they are only
printed when debugging is enabled.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>