This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.

Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: NThierry Reding <treding@nvidia.com>

When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.

HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The correct check is for 48 kHz, not 480 kHz. Found by Coverity.
Signed-off-by: NThierry Reding <treding@nvidia.com>

These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NThierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: NThierry Reding <treding@nvidia.com>

All APIs that the driver uses are exported, so the driver can now be
built as a module.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Tegra124 has 192 syncpoints whereas its predecessors had 32 syncpoints.
This required changes to the hardware register layout.
Signed-off-by: NArto Merilainen <amerilainen@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Treat both negative and zero return values from clk_round_rate() as
errors.  This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.

Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error.  All other values will be considered valid
rates.  The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: NPaul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

When debugfs support isn't enabled, gcc complains about some variables
being unused. To avoid further #ifdefery, move debugfs specific setup
code into static functions and use IS_ENABLED(CONFIG_DEBUG_FS) to have
the compiler, rather than the preprocessor, discard them when unused.
The advantage of doing it this way is that all the code will be
compile-tested whether or not debugfs support is enabled.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: NThierry Reding <treding@nvidia.com>

An earlier patch added a subset of the required HW specific header files
but didn't actually include the right ones when compiling for host1x02.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Make the public API symbols visible so that depending drivers can be
built as a module.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This driver adds support to perform calibration of the MIPI pads for CSI
and DSI.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Panasonic VVX10F004B0 is a 10.1" WUXGA TFT LCD panel connected using
four DSI lanes.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add a driver for simple panels. Such panels can have a regulator that
provides the supply voltage and a separate GPIO to enable the panel.
Optionally the panels can have a backlight associated with them so it
can be enabled or disabled according to the panel's power management
mode.

Support is added for two panels: An AU Optronics 10.1" WSVGA and a
Chunghwa Picture Tubes 10.1" WXGA panel.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add a very simple framework to register and lookup panels. Panel drivers
can initialize a DRM panel and register it with the framework, allowing
them to be retrieved and used by display drivers. Currently only support
for DPMS and obtaining panel modes is provided. However it should be
sufficient to enable a large number of panels. The framework should also
be easily extensible to support more sophisticated kinds of panels such
as DSI.

The framework hasn't been tied into the DRM core, even though it should
be easily possible to do so if that's what we want. In the current
implementation, display drivers can simple make use of it to retrieve a
panel, obtain its modes and control its DPMS mode.

Note that this is currently only tested on systems that boot from a
device tree. No glue code has been written yet for systems that use
platform data, but it should be easy to add.
Signed-off-by: NThierry Reding <treding@nvidia.com>

MIPI DSI bus allows to model DSI hosts and DSI peripherals using the
Linux driver model. DSI hosts are registered by the DSI host drivers.
During registration DSI peripherals will be created from the children
of the DSI host's device tree node. Support for registration from
board-setup code will be added later when needed.

DSI hosts expose operations which can be used by DSI peripheral drivers
to access associated devices.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Since commit ec39f64b ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.

Fix them by using dev_get_drvdata(), in order to avoid this oops:

  BUG: unable to handle kernel paging request at 0000000000001e28
  IP: [<ffffffffa02ae8b4>] hwmon_attributes_visible+0x18/0x3d [radeon]
  PGD 15057e067 PUD 151a8e067 PMD 0
  Oops: 0000 [#1] PREEMPT SMP
  Call Trace:
    internal_create_group+0x114/0x1d9
    sysfs_create_group+0xe/0x10
    sysfs_create_groups+0x22/0x5f
    device_add+0x34f/0x501
    device_register+0x15/0x18
    hwmon_device_register_with_groups+0xb5/0xed
    radeon_hwmon_init+0x56/0x7c [radeon]
    radeon_pm_init+0x134/0x7e5 [radeon]
    radeon_modeset_init+0x75f/0x8ed [radeon]
    radeon_driver_load_kms+0xc6/0x187 [radeon]
    drm_dev_register+0xf9/0x1b4 [drm]
    drm_get_pci_dev+0x98/0x129 [drm]
    radeon_pci_probe+0xa3/0xac [radeon]
    pci_device_probe+0x6e/0xcf
    driver_probe_device+0x98/0x1c4
    __driver_attach+0x5c/0x7e
    bus_for_each_dev+0x7b/0x85
    driver_attach+0x19/0x1b
    bus_add_driver+0x104/0x1ce
    driver_register+0x89/0xc5
    __pci_register_driver+0x58/0x5b
    drm_pci_init+0x86/0xea [drm]
    radeon_init+0x97/0x1000 [radeon]
    do_one_initcall+0x7f/0x117
    load_module+0x1583/0x1bb4
    SyS_init_module+0xa0/0xaf
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-By: NTerje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>

Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-By: NTerje Bergstrom <tbergstrom@nvidia.com>

Ensure the side-by-side (half) flag is added to any existing flags when
adding modes from 3D_Structure_ALL.
Signed-off-by: NThomas Wood <thomas.wood@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Wood <thomas.wood@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When probing the bus, we need to set the byte count
to 0 rather than 1.

v2: Don't count the first byte.

bug:
https://bugzilla.kernel.org/show_bug.cgi?id=66241Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Don't crash if the encoder does not have an afmt struct.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72283Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some boards seem to have garbage in the upper
16 bits of the vram size register.  Check for
this and clamp the size properly.  Fixes
boards reporting bogus amounts of vram.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

5dc9e1e8 was a bit over-ambitious, and accidentially removed handling
for imported prime buffers.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some user-space apps expects to find them there.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

Also request kernel ttm_buffer objects for buffer objects that obviously
aren't visible to user-space, and save some device address space.

The accounting was broken in a couple of ways:
1) We did not differentiate between user dma buffers and kernel dma buffers.
2) The ttm_bo_acc_size function is broken in that it
a) Doesn't take into account the size of the optional dma address array,
b) Doesn't take into account the fact that drivers typically embed the
ttm_tt structure.

This needs to be fixed in ttm, but meanwhile provide a vmwgfx-specific
function to do the job.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

Allocation was duplicating code. Comments were missing.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

Failure to do this would make the drm_mode_get_crtc ioctl return
without crtc mode info, indicating that no mode was set.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

We should be taking the minimum here instead of the max.  It could lead
to a buffer overflow.

Fixes: 438d99e3 ('drm/nvd0/disp: initial crtc object implementation')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>

a/drm/nv50_display.c b/drm/nv50_display.c
index f8e66c08b11a..4e384a2f99c3 100644

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NRoy Spliet <rspliet@eclipso.eu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NRoy Spliet <rspliet@eclipso.eu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>