- 03 12月, 2013 10 次提交
-
-
由 Linus Torvalds 提交于
Merge branch 'leds-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds Pull LED subsystem bugfix from Bryan Wu. * 'leds-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: leds: pwm: Fix for deferred probe in DT booted mode
-
由 Peter Ujfalusi 提交于
We need to make sure that the error code from devm_of_pwm_get() is the one the module returns in case of failure. Restructure the code to make this possible for DT booted case. With this patch the driver can ask for deferred probing when the board is booted with DT. Fixes for example omap4-sdp board's keyboard backlight led. Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NBryan Wu <cooloney@gmail.com>
-
由 Linus Torvalds 提交于
In commit 7314e613 ("Fix a few incorrectly checked [io_]remap_pfn_range() calls") the uio driver started more properly checking the passed-in user mapping arguments against the size of the actual uio driver data. That in turn exposed that some driver authors apparently didn't realize that mmap can only work on a page granularity, and had tried to use it with smaller mappings, with the new size check catching that out. So since it's not just the user mmap() arguments that can be confused, make the uio mmap code also verify that the uio driver has the memory allocated at page boundaries in order for mmap to work. If the device memory isn't properly aligned, we return [ENODEV] The fildes argument refers to a file whose type is not supported by mmap(). as per the open group documentation on mmap. Reported-by: NHolger Brunck <holger.brunck@keymile.com> Acked-by: NGreg KH <gregkh@linuxfoundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull irq fixes from Thomas Gleixner: - Correction of fuzzy and fragile IRQ_RETVAL macro - IRQ related resume fix affecting only XEN - ARM/GIC fix for chained GIC controllers * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip: Gic: fix boot for chained gics irq: Enable all irqs unconditionally in irq_resume genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull scheduler fixes from Ingo Molnar: "Various smaller fixlets, all over the place" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/doc: Fix generation of device-drivers sched: Expose preempt_schedule_irq() sched: Fix a trivial typo in comments sched: Remove unused variable in 'struct sched_domain' sched: Avoid NULL dereference on sd_busy sched: Check sched_domain before computing group power MAINTAINERS: Update file patterns in the lockdep and scheduler entries
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull perf fixes from Ingo Molnar: "Misc kernel and tooling fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tools lib traceevent: Fix conversion of pointer to integer of different size perf/trace: Properly use u64 to hold event_id perf: Remove fragile swevent hlist optimization ftrace, perf: Avoid infinite event generation loop tools lib traceevent: Fix use of multiple options in processing field perf header: Fix possible memory leaks in process_group_desc() perf header: Fix bogus group name perf tools: Tag thread comm as overriden
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip由 Linus Torvalds 提交于
Pull Xen bug-fixes from Konrad Rzeszutek Wilk: "Fixes to patches that went in this merge window along with a latent bug: - Fix lazy flushing in case m2p override fails. - Fix module compile issues with ARM/Xen - Add missing call to DMA map page for Xen SWIOTLB for ARM" * tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/gnttab: leave lazy MMU mode in the case of a m2p override failure xen/arm: p2m_init and p2m_lock should be static arm/xen: Export phys_to_mach to fix Xen module link errors swiotlb-xen: add missing xen_dma_map_page call
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi由 Linus Torvalds 提交于
Pull spi fixes from Mark Brown: "A smattering of driver specific fixes here, including a bunch for a long standing common pattern in the error handling paths, and a fix for an embarrassing thinko in the new devm master registration code" * tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: spi/pxa2xx: Restore private register bits. spi/qspi: Fix qspi remove path. spi/qspi: cleanup pm_runtime error check. spi/qspi: set correct platform drvdata in ti_qspi_probe() spi/pxa2xx: add new ACPI IDs spi: core: invert success test in devm_spi_register_master spi: spi-mxs: fix reference leak to master in mxs_spi_remove() spi: bcm63xx: fix reference leak to master in bcm63xx_spi_remove() spi: txx9: fix reference leak to master in txx9spi_remove() spi: mpc512x: fix reference leak to master in mpc512x_psc_spi_do_remove() spi: rspi: use platform drvdata correctly in rspi_remove() spi: bcm2835: fix reference leak to master in bcm2835_spi_remove()
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking updates from David Miller: "Here is a pile of bug fixes that accumulated while I was in Europe" 1) In fixing kernel leaks to userspace during copying of socket addresses, we broke a case that used to work, namely the user providing a buffer larger than the in-kernel generic socket address structure. This broke Ruby amongst other things. Fix from Dan Carpenter. 2) Fix regression added by byte queue limit support in 8139cp driver, from Yang Yingliang. 3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage implementations, they should just treat it the same as MSG_MORE. Fix from Richard Weinberger and Shawn Landden. 4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from Oussama Ghorbel. In particular we should send an ICMPv6 unreachable in such situations. 5) Fix some regressions in the recent genetlink fixes, in particular get the pmcraid driver to use the new safer interfaces correctly. From Johannes Berg. 6) macvtap was converted to use a per-cpu set of statistics, but some code was still bumping tx_dropped elsewhere. From Jason Wang. 7) Fix build failure of xen-netback due to missing include on some architectures, from Andy Whitecroft. 8) macvtap double counts received packets in statistics, fix from Vlad Yasevich. 9) Fix various cases of using *_STATS_BH() when *_STATS() is more appropriate. From Eric Dumazet and Hannes Frederic Sowa. 10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum properly after encapsulation. Fix from Fan Du. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits) net/mlx4_en: Remove selftest TX queues empty condition {pktgen, xfrm} Update IPv4 header total len and checksum after tranformation virtio_net: make all RX paths handle erors consistently virtio_net: fix error handling for mergeable buffers virtio_net: Fixed a trivial typo (fitler --> filter) netem: fix gemodel loss generator netem: fix loss 4 state model netem: missing break in ge loss generator net/hsr: Support iproute print_opt ('ip -details ...') net/hsr: Very small fix of comment style. MAINTAINERS: Added net/hsr/ maintainer ipv6: fix possible seqlock deadlock in ip6_finish_output2 ixgbe: Make ixgbe_identify_qsfp_module_generic static ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default ixgbe: ixgbe_fwd_ring_down needs to be static e1000: fix possible reset_task running after adapter down e1000: fix lockdep warning in e1000_reset_task e1000: prevent oops when adapter is being closed and reset simultaneously igb: Fixed Wake On LAN support inet: fix possible seqlock deadlocks ...
-
由 Linus Torvalds 提交于
The pipe code was trying (and failing) to be very careful about freeing the pipe info only after the last access, with a pattern like: spin_lock(&inode->i_lock); if (!--pipe->files) { inode->i_pipe = NULL; kill = 1; } spin_unlock(&inode->i_lock); __pipe_unlock(pipe); if (kill) free_pipe_info(pipe); where the final freeing is done last. HOWEVER. The above is actually broken, because while the freeing is done at the end, if we have two racing processes releasing the pipe inode info, the one that *doesn't* free it will decrement the ->files count, and unlock the inode i_lock, but then still use the "pipe_inode_info" afterwards when it does the "__pipe_unlock(pipe)". This is *very* hard to trigger in practice, since the race window is very small, and adding debug options seems to just hide it by slowing things down. Simon originally reported this way back in July as an Oops in kmem_cache_allocate due to a single bit corruption (due to the final "spin_unlock(pipe->mutex.wait_lock)" incrementing a field in a different allocation that had re-used the free'd pipe-info), it's taken this long to figure out. Since the 'pipe->files' accesses aren't even protected by the pipe lock (we very much use the inode lock for that), the simple solution is to just drop the pipe lock early. And since there were two users of this pattern, create a helper function for it. Introduced commit ba5bb147 ("pipe: take allocation and freeing of pipe_inode_info out of ->i_mutex"). Reported-by: NSimon Kirby <sim@hostway.ca> Reported-by: NIan Applegate <ia@cloudflare.com> Acked-by: NAl Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # v3.10+ Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 02 12月, 2013 6 次提交
-
-
由 Eugenia Emantayev 提交于
Remove waiting for TX queues to become empty during selftest. This check is not necessary for any purpose, and might put the driver into an infinite loop. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 fan.du 提交于
commit a553e4a6 ("[PKTGEN]: IPSEC support") tried to support IPsec ESP transport transformation for pktgen, but acctually this doesn't work at all for two reasons(The orignal transformed packet has bad IPv4 checksum value, as well as wrong auth value, reported by wireshark) - After transpormation, IPv4 header total length needs update, because encrypted payload's length is NOT same as that of plain text. - After transformation, IPv4 checksum needs re-caculate because of payload has been changed. With this patch, armmed pktgen with below cofiguration, Wireshark is able to decrypted ESP packet generated by pktgen without any IPv4 checksum error or auth value error. pgset "flag IPSEC" pgset "flows 1" Signed-off-by: NFan Du <fan.du@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael S. Tsirkin 提交于
receive mergeable now handles errors internally. Do same for big and small packet paths, otherwise the logic is too hard to follow. Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Acked-by: NJason Wang <jasowang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael S. Tsirkin 提交于
Eric Dumazet noticed that if we encounter an error when processing a mergeable buffer, we don't dequeue all of the buffers from this packet, the result is almost sure to be loss of networking. Jason Wang noticed that we also leak a page and that we don't decrement the rq buf count, so we won't repost buffers (a resource leak). Fix both issues. Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael Dalton <mwdalton@google.com> Reported-by: NEric Dumazet <edumazet@google.com> Reported-by: NJason Wang <jasowang@redhat.com> Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Acked-by: NJason Wang <jasowang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml由 Linus Torvalds 提交于
Pull UML fixes from Richard Weinberger: "Fixes two regressions which got introduced this merge window" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: um: Build always with -mcmodel=large on 64bit um: Rename print_stack_trace to do_stack_trace
-
git://ftp.arm.linux.org.uk/~rmk/linux-arm由 Linus Torvalds 提交于
Pull ARM fixes from Russell King: "Some ARM fixes, the biggest of which is the fix for the signal return codes; this came up due to an interaction between the V7M nommu changes and the BE8 changes. Dave Martin spotted that the kexec trampoline wasn't being correctly copied (in a way which allows Thumb-2 to work). I've also fixed a number of breakages on footbridge platforms as I've upgraded one of my machines to v3.12... one which had a 1200 day uptime" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 7907/1: lib: delay-loop: Add align directive to fix BogoMIPS calculation ARM: 7897/1: kexec: Use the right ISA for relocate_new_kernel ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S ARM: footbridge: fix EBSA285 LEDs ARM: footbridge: fix VGA initialisation ARM: fix booting low-vectors machines ARM: dma-mapping: check DMA mask against available memory
-
- 01 12月, 2013 15 次提交
-
-
由 Richard Weinberger 提交于
On UML SUBARCH can be x86, x86_64 and i386 and if it is x86 we use uname -m to select a defconfig. Therefore we can no longer use -mcmodel=large only if SUBARCH is x86_64. Reported-and-tested-by: NBoaz Harrosh <bharrosh@panasas.com> Signed-off-by: NRichard Weinberger <richard@nod.at>
-
由 Richard Weinberger 提交于
We cannot use print_stack_trace because the name conflicts with linux/stacktrace.h. Reported-by: NRandy Dunlap <rdunlap@infradead.org> Acked-by: NRandy Dunlap <rdunlap@infradead.org> Signed-off-by: NRichard Weinberger <richard@nod.at>
-
由 Fabio Estevam 提交于
Currently mx53 (CortexA8) running at 1GHz reports: Calibrating delay loop... 663.55 BogoMIPS (lpj=3317760) Tom Evans verified that alignments of 0x0 and 0x8 run the two instructions of __loop_delay in one clock cycle (1 clock/loop), while alignments of 0x4 and 0xc take 3 clocks to run the loop twice. (1.5 clock/loop) The original object code looks like this: 00000010 <__loop_const_udelay>: 10: e3e01000 mvn r1, #0 14: e51f201c ldr r2, [pc, #-28] ; 0 <__loop_udelay-0x8> 18: e5922000 ldr r2, [r2] 1c: e0800921 add r0, r0, r1, lsr #18 20: e1a00720 lsr r0, r0, #14 24: e0822b21 add r2, r2, r1, lsr #22 28: e1a02522 lsr r2, r2, #10 2c: e0000092 mul r0, r2, r0 30: e0800d21 add r0, r0, r1, lsr #26 34: e1b00320 lsrs r0, r0, #6 38: 01a0f00e moveq pc, lr 0000003c <__loop_delay>: 3c: e2500001 subs r0, r0, #1 40: 8afffffe bhi 3c <__loop_delay> 44: e1a0f00e mov pc, lr After adding the 'align 3' directive to __loop_delay (align to 8 bytes): 00000010 <__loop_const_udelay>: 10: e3e01000 mvn r1, #0 14: e51f201c ldr r2, [pc, #-28] ; 0 <__loop_udelay-0x8> 18: e5922000 ldr r2, [r2] 1c: e0800921 add r0, r0, r1, lsr #18 20: e1a00720 lsr r0, r0, #14 24: e0822b21 add r2, r2, r1, lsr #22 28: e1a02522 lsr r2, r2, #10 2c: e0000092 mul r0, r2, r0 30: e0800d21 add r0, r0, r1, lsr #26 34: e1b00320 lsrs r0, r0, #6 38: 01a0f00e moveq pc, lr 3c: e320f000 nop {0} 00000040 <__loop_delay>: 40: e2500001 subs r0, r0, #1 44: 8afffffe bhi 40 <__loop_delay> 48: e1a0f00e mov pc, lr 4c: e320f000 nop {0} , which now reports: Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) Some more test results: On mx31 (ARM1136) running at 532 MHz, before the patch: Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184) On mx31 (ARM1136) running at 532 MHz after the patch: Calibrating delay loop... 528.79 BogoMIPS (lpj=2643968) Also tested on mx6 (CortexA9) and on mx27 (ARM926), which shows the same BogoMIPS value before and after this patch. Reported-by: NTom Evans <tom_usenet@optusnet.com.au> Suggested-by: NTom Evans <tom_usenet@optusnet.com.au> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Dave Martin 提交于
Copying a function with memcpy() and then trying to execute the result isn't trivially portable to Thumb. This patch modifies the kexec soft restart code to copy its assembler trampoline relocate_new_kernel() using fncpy() instead, so that relocate_new_kernel can be in the same ISA as the rest of the kernel without problems. Signed-off-by: NDave Martin <Dave.Martin@arm.com> Acked-by: NWill Deacon <will.deacon@arm.com> Reported-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org> Tested-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Victor Kamensky 提交于
After "ARM: signal: sigreturn_codes should be endian neutral to work in BE8" commit, thumb only platforms, like armv7m, fails to compile sigreturn_codes.S. The reason is that for such arch values '.arm' directive and arm opcodes are not allowed. Fix conditionally enables arm opcodes only if no CONFIG_CPU_THUMBONLY defined and it uses .org instructions to keep sigreturn_codes layout. Suggested-by: NDave Martin <Dave.Martin@arm.com> Signed-off-by: NVictor Kamensky <victor.kamensky@linaro.org> Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: NDave Martin <Dave.Martin@arm.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
- The LEDs register is write-only: it can't be read-modify-written. - The LEDs are write-1-for-off not 0. - The check for the platform was inverted. Fixes: cf6856d6 ("ARM: mach-footbridge: retire custom LED code") Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Cc: stable@vger.kernel.org
-
由 Thomas Huth 提交于
"MAC filter" sounds more reasonable than "MAC fitler". Signed-off-by: NThomas Huth <thuth@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Patch from developers of the alternative loss models, downloaded from: http://netgroup.uniroma2.it/twiki/bin/view.cgi/Main/NetemCLG "in case 2, of the switch we change the direction of the inequality to net_random()>clg->a3, because clg->a3 is h in the GE model and when h is 0 all packets will be lost." Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Patch from developers of the alternative loss models, downloaded from: http://netgroup.uniroma2.it/twiki/bin/view.cgi/Main/NetemCLG "In the case 1 of the switch statement in the if conditions we need to add clg->a4 to clg->a1, according to the model." Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
There is a missing break statement in the Gilbert Elliot loss model generator which makes state machine behave incorrectly. Reported-by: Martin Burri <martin.burri@ch.abb.com Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arvid Brodin 提交于
This implements the rtnl_link_ops fill_info routine for HSR. Signed-off-by: NArvid Brodin <arvid.brodin@alten.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arvid Brodin 提交于
Signed-off-by: NArvid Brodin <arvid.brodin@alten.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arvid Brodin 提交于
Signed-off-by: NArvid Brodin <arvid.brodin@alten.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Frederic Sowa 提交于
IPv6 stats are 64 bits and thus are protected with a seqlock. By not disabling bottom-half we could deadlock here if we don't disable bh and a softirq reentrantly updates the same mib. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net由 David S. Miller 提交于
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to igb, e1000 and ixgbe. Akeem provides a igb fix where WOL was being reported as supported on some ethernet devices which did not have that capability. Yanjun provides a fix for e1000 which is similar to a previous fix for e1000e commit bb9e44d0 ("e1000e: prevent oops when adapter is being closed and reset simultaneously"), where the same issue was observed on the older e1000 cards. Vladimir Davydov provides 2 e1000 fixes. The first fixes a lockdep warning e1000_down() tries to synchronously cancel e1000 auxiliary works (reset_task, watchdog_task, phy_info_task and fifo_stall_task) which take adapter->mutex in their handlers. The second patch is to fix a possible race condition where reset_task() would be running after adapter down. John provides 2 fixes for ixgbe. First turns ixgbe_fwd_ring_down to static and the second disables NETIF_F_HW_L2FW_DOFFLOAD by default because it allows upper layer net devices to use queues in the hardware to directly submit and receive skbs. Mark Rustad provides a single patch for ixgbe to make ixgbe_identify_qsfp_module_generic static to resolve compile warnings. v2: Drop igb patch "igb: Update queue reinit function to call dev_close when init of queues fails" from Carolyn, so that the solution can be re-worked based on feedback from David Miller. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 11月, 2013 9 次提交
-
-
由 Russell King 提交于
It's no good setting vga_base after the VGA console has been initialised, because if we do that we get this: Unable to handle kernel paging request at virtual address 000b8000 pgd = c0004000 [000b8000] *pgd=07ffc831, *pte=00000000, *ppte=00000000 0Internal error: Oops: 5017 [#1] ARM Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0+ #49 task: c03e2974 ti: c03d8000 task.ti: c03d8000 PC is at vgacon_startup+0x258/0x39c LR is at request_resource+0x10/0x1c pc : [<c01725d0>] lr : [<c0022b50>] psr: 60000053 sp : c03d9f68 ip : 000b8000 fp : c03d9f8c r10: 000055aa r9 : 4401a103 r8 : ffffaa55 r7 : c03e357c r6 : c051b460 r5 : 000000ff r4 : 000c0000 r3 : 000b8000 r2 : c03e0514 r1 : 00000000 r0 : c0304971 Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel which is an access to the 0xb8000 without the PCI offset required to make it work. Fixes: cc22b4c1 ("ARM: set vga memory base at run-time") Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Cc: <stable@vger.kernel.org>
-
由 Russell King 提交于
Commit f6f91b0d (ARM: allow kuser helpers to be removed from the vector page) required two pages for the vectors code. Although the code setting up the initial page tables was updated, the code which allocates page tables for new processes wasn't, neither was the code which tears down the mappings. Fix this. Fixes: f6f91b0d ("ARM: allow kuser helpers to be removed from the vector page") Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Cc: <stable@vger.kernel.org>
-
由 Russell King 提交于
Some buses have negative offsets, which causes the DMA mask checks to falsely fail. Fix this by using the actual amount of memory fitted in the system. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Mark Rustad 提交于
Correct a namespace complaint by making the function static and moving the prototype into the .c file. Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 John Fastabend 提交于
NETIF_F_HW_L2FW_DOFFLOAD allows upper layer net devices such as macvlan to use queues in the hardware to directly submit and receive skbs. This creates a subtle change in the datapath though. One change being the skb may no longer use the root devices qdisc. Because users may not expect this we can't enable the feature by default unless the hardware can offload all the software functionality above it. So for now disable it by default and let users opt in. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 John Fastabend 提交于
When compiling with -Wstrict-prototypes gcc catches a static I missed. ./ixgbe_main.c:4254: warning: no previous prototype for 'ixgbe_fwd_ring_down' Reported-by: NPhillip Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Vladimir Davydov 提交于
On e1000_down(), we should ensure every asynchronous work is canceled before proceeding. Since the watchdog_task can schedule other works apart from itself, it should be stopped first, but currently it is stopped after the reset_task. This can result in the following race leading to the reset_task running after the module unload: e1000_down_and_stop(): e1000_watchdog(): ---------------------- ----------------- cancel_work_sync(reset_task) schedule_work(reset_task) cancel_delayed_work_sync(watchdog_task) The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning of e1000_down_and_stop() thus ensuring the race is impossible. Cc: Tushar Dave <tushar.n.dave@intel.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: NVladimir Davydov <vdavydov@parallels.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Vladimir Davydov 提交于
The patch fixes the following lockdep warning, which is 100% reproducible on network restart: ====================================================== [ INFO: possible circular locking dependency detected ] 3.12.0+ #47 Tainted: GF ------------------------------------------------------- kworker/1:1/27 is trying to acquire lock: ((&(&adapter->watchdog_task)->work)){+.+...}, at: [<ffffffff8108a5b0>] flush_work+0x0/0x70 but task is already holding lock: (&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&adapter->mutex){+.+...}: [<ffffffff810bdb5d>] lock_acquire+0x9d/0x120 [<ffffffff816b8cbc>] mutex_lock_nested+0x4c/0x390 [<ffffffffa017233d>] e1000_watchdog+0x7d/0x5b0 [e1000] [<ffffffff8108b972>] process_one_work+0x1d2/0x510 [<ffffffff8108ca80>] worker_thread+0x120/0x3a0 [<ffffffff81092c1e>] kthread+0xee/0x110 [<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0 -> #0 ((&(&adapter->watchdog_task)->work)){+.+...}: [<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810 [<ffffffff810bdb5d>] lock_acquire+0x9d/0x120 [<ffffffff8108a5eb>] flush_work+0x3b/0x70 [<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140 [<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20 [<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000] [<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000] [<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000] [<ffffffff8108b972>] process_one_work+0x1d2/0x510 [<ffffffff8108ca80>] worker_thread+0x120/0x3a0 [<ffffffff81092c1e>] kthread+0xee/0x110 [<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&adapter->mutex); lock((&(&adapter->watchdog_task)->work)); lock(&adapter->mutex); lock((&(&adapter->watchdog_task)->work)); *** DEADLOCK *** 3 locks held by kworker/1:1/27: #0: (events){.+.+.+}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510 #1: ((&adapter->reset_task)){+.+...}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510 #2: (&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000] stack backtrace: CPU: 1 PID: 27 Comm: kworker/1:1 Tainted: GF 3.12.0+ #47 Hardware name: System manufacturer System Product Name/P5B-VM SE, BIOS 0501 05/31/2007 Workqueue: events e1000_reset_task [e1000] ffffffff820f6000 ffff88007b9dba98 ffffffff816b54a2 0000000000000002 ffffffff820f5e50 ffff88007b9dbae8 ffffffff810ba936 ffff88007b9dbac8 ffff88007b9dbb48 ffff88007b9d8f00 ffff88007b9d8780 ffff88007b9d8f00 Call Trace: [<ffffffff816b54a2>] dump_stack+0x49/0x5f [<ffffffff810ba936>] print_circular_bug+0x216/0x310 [<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810 [<ffffffff8108a5b0>] ? __flush_work+0x250/0x250 [<ffffffff810bdb5d>] lock_acquire+0x9d/0x120 [<ffffffff8108a5b0>] ? __flush_work+0x250/0x250 [<ffffffff8108a5eb>] flush_work+0x3b/0x70 [<ffffffff8108a5b0>] ? __flush_work+0x250/0x250 [<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140 [<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20 [<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000] [<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000] [<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000] [<ffffffff8108b972>] process_one_work+0x1d2/0x510 [<ffffffff8108b906>] ? process_one_work+0x166/0x510 [<ffffffff8108ca80>] worker_thread+0x120/0x3a0 [<ffffffff8108c960>] ? manage_workers+0x2c0/0x2c0 [<ffffffff81092c1e>] kthread+0xee/0x110 [<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70 [<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0 [<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70 == The issue background == The problem occurs, because e1000_down(), which is called under adapter->mutex by e1000_reset_task(), tries to synchronously cancel e1000 auxiliary works (reset_task, watchdog_task, phy_info_task, fifo_stall_task), which take adapter->mutex in their handlers. So the question is what does adapter->mutex protect there? The adapter->mutex was introduced by commit 0ef4ee ("e1000: convert to private mutex from rtnl") as a replacement for rtnl_lock() taken in the asynchronous handlers. It targeted on fixing a similar lockdep warning issued when e1000_down() was called under rtnl_lock(), and it fixed it, but unfortunately it introduced the lockdep warning described above. Anyway, that said the source of this bug is that the asynchronous works were made to take rtnl_lock() some time ago, so let's look deeper and find why it was added there. The rtnl_lock() was added to asynchronous handlers by commit 338c15 ("e1000: fix occasional panic on unload") in order to prevent asynchronous handlers from execution after the module is unloaded (e1000_down() is called) as it follows from the comment to the commit: > Net drivers in general have an issue where timers fired > by mod_timer or work threads with schedule_work are running > outside of the rtnl_lock. > > With no other lock protection these routines are vulnerable > to races with driver unload or reset paths. > > The longer term solution to this might be a redesign with > safer locks being taken in the driver to guarantee no > reentrance, but for now a safe and effective fix is > to take the rtnl_lock in these routines. I'm not sure if this locking scheme fixed the problem or just made it unlikely, although I incline to the latter. Anyway, this was long time ago when e1000 auxiliary works were implemented as timers scheduling real work handlers in their routines. The e1000_down() function only canceled the timers, but left the real handlers running if they were running, which could result in work execution after module unload. Today, the e1000 driver uses sane delayed works instead of the pair timer+work to implement its delayed asynchronous handlers, and the e1000_down() synchronously cancels all the works so that the problem that commit 338c15 tried to cope with disappeared, and we don't need any locks in the handlers any more. Moreover, any locking there can potentially result in a deadlock. So, this patch reverts commits 0ef4ee and 338c15. Fixes: 0ef4eedc ("e1000: convert to private mutex from rtnl") Fixes: 338c15e4 ("e1000: fix occasional panic on unload") Cc: Tushar Dave <tushar.n.dave@intel.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: NVladimir Davydov <vdavydov@parallels.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 yzhu1 提交于
This change is based on a similar change made to e1000e support in commit bb9e44d0 ("e1000e: prevent oops when adapter is being closed and reset simultaneously"). The same issue has also been observed on the older e1000 cards. Here, we have increased the RESET_COUNT value to 50 because there are too many accesses to e1000 nic on stress tests to e1000 nic, it is not enough to set RESET_COUT 25. Experimentation has shown that it is enough to set RESET_COUNT 50. Signed-off-by: Nyzhu1 <yanjun.zhu@windriver.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-